2012 AUDI Q7 Owner´s Manual

Front towing loop
Do not install the front towing loop until it is
needed.
Fig. 262 Right front bumper: Removing the cover
Fig. 263 Righ t fron t bumper w ith out cover: Screwing
i n towing loop
The towing loop fits into the threaded hole lo­
cated on the right side of the front bumper
and covered by a cover when not in use.
.. Remove the towing loop from the vehicle
tool kit
c:> page 295.
.. Carefully remove the cover c:> fig. 262.
.. Screw the towing loop tightly into the
threaded hole as far as it will go
c:> fig . 263 .
When it is no longer needed, unscrew the
towing loop and put it back into the vehicle
toolkit . Be sure to have the towing loop stored
in the vehicle at all times .
_&, WARNING
If the towing loop is not screwed in as far
as it w ill go, the th read can pull out when
t he vehicle is towed -potential risk of an
accident.
Emergenc y situ ation s 311
Rear towing loop
Do not install the rear towing loop until it is
needed .
Fig . 264 Rea r bumper: Cover
Fig. 265 Rea r bumper: Screw ing in tow ing loop
On the right s ide of the rear bumper there is a
th readed hole for the towing loop. The
threaded hole is protected by a cover.
.,. Remove the tow ing loop from the vehicle
too l kit
c:> page 295 .
.. To release the cover from the bumper, press
it in by applying sho rt, sharp pressure to the
outer part
c:> fig . 264.
.. Screw the tow ing loop t ightly i nto the
threaded ho le as far as it wi ll go
c:> fig. 265.
Unscrew the towing loop again afte r use and
install the cover in the bumper. Return the
towing loop to the toolkit . Be sure to have the
towing loop stored in the vehicle at all times.
_&, WARNING
If the tow ing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potent ia l risk of an
accide nt.

312 Emergency situations
loading the vehicle onto a flat bed truck
Fig . 26 6 Vehicle o n flat bed truck
Front hook up
,,. Align the ve hicle with the centerline of the
car carr ier ramp.
,,. Attach the winch hook to the front towline
eye previously insta lled.
Rear hook up
,,. Align the ve hicle with the centerline of the
ca r ca rr ier ramp .
,,. Attach t he winch hook to the rear towline
eye previously installed.
{!) Tips
C heck carefully to make sure the hook- up
is sec ure be fore moving the car up the flat­
bed truck ramp.
Lifting vehicle
lifting with workshop hoist and with
floor jack
T he vehicle may only be li~ed at the lifting
points illustrated .
Fig . 267 Fro nt lift ing point
Fig . 268 Rear lifting point
,,. Read and heed WARNI NG q ,,&. .
,,. Loc ate lifting poi nts q fig. 267 a nd
qfig. 268 .
,,. Adjust lifting arms of wo rks hop ho ist o r
floor ja ck to ma tc h veh icle lift ing po ints .
,,. Insert a rubber pad be tween the floo r ja ck /
workshop hoist and t he lift ing points.
If you mu st lift your vehicle with a floor jack
to work underneath, be sure the vehicle is safely supported on stand s intended for this
purpose.
Front lifting point
T he lift ing po in t i s l oca ted o n the flo or pan re ­
i n forcemen t about a t the s ame leve l as the
jac k mounting point
q fig. 267 . Do not lift
the vehicle at the vertical sill reinforcement .
Rear lifting point
T he lifti ng poi nt is located o n the vert ic al rei n­
f o rc emen t of th e lower sill for the onbo ard
jac k
c> fig. 268.
lifting with vehicle jack
Refer to c:> page 300 .
A WARNING
---To re duc e th e risk of s erious injury and
veh icle da mage.
- Always lift the vehicle on ly at the spe­
c ia l workshop hoist and floor jac k lift
po ints illust rated
c> fig. 267 and
c> fig. 268 .
- Fail ure t o lift the ve hicle at these
po ints could cause the vehicle to tilt or ,...

fall f rom a lift if the re is a change in ve­
h icle we ight d istr ibut ion and balance.
This might happen, for examp le, when
heavy components such as the engi ne
b lock or transmiss io n are removed .
- Whe n removing heavy components like
these, ancho r vehicle to ho ist o r add cor­
respond ing weig hts to ma inta in the cen ­
te r of g ravity . Othe rwise, the vehicl e
m ig ht tilt o r slip off th e hois t, causi ng
s erious perso nal inju ry.
(D Note
- Be awa re of the fo llowing po in ts befo re
li fting t he vehi cle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to serious
damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­ ance between the hoist and low parts
of the vehicle .
Emergency situations 313
•
•

314 General information
General information Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::>page 316. This sec ­
tion provides general information, notes and restrictions which apply to this data .
Vehicle identification
The key data is given on the vehicle identifica­
tion number (VIN) plate and the vehicle data
sticker.
Fig. 269 Veh icle Ide ntific atio n Number (VlN) p late: lo ­
cation on driver 's sid e das h panel
Fig. 270 The vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
b le from the outside through the windshield
r:::> fig . 269. You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select function button
!CAR l > control
button
Systems* > Vehicle ID number (VIN)
or ICARI > control button Car systems*> Serv­
icing
& checks> VIN number . The
vehicle identification label
is located in the luggage compartment under
the cargo floor cover.
The label¢
fig. 2 70 shows the following vehi­
cle data :
(D Production control No.
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is you r assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
t ime the vehicle was manufactured . You can
find this sticker on the left door jamb .
It
shows the month and year of production and
the vehicle ident ification number of your vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carrier.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus fu ll fuel tank,
oi l and coolant, plus maximum load , which in­
cludes passenger weight (150 lbs/68 kg per
Ill>

designated seating position) and luggage
weight~&. .
Gros s Axle W eight Rating
The G ross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
vehicle
q .&. .
Vehicle capacit y weight
The vehicle capac ity we ight (max. load) is list­
ed on the driver 's side B-p illar.
Roof weight
The maximum permissible roof weight is 220
lb (100 kg ).
The roof weight is made up of
the we ight of the roof rack system and the
weight of the object be ing transported
q page 84, Loading the roof rack.
..&, WARNING
- The Gross Vehicle Weight Rat ing for yo ur
Audi Q7 vehicle, found on the safety compliance label on the driver's side B ­
pillar, must never be exceeded under any
circumstances. Exceed ing the Gross Vehi­
cle Weight Rating of your vehicle is like ly
to damage your vehicle, and such dam­
age will not be covered by your Limited
New Vehicle Warranty . Exceeding the
Gross Vehicle We ight Rating will also
change the performance and handling
characteristics of your vehicle, which
cou ld cause a crash result ing in serious
injury o r death.
- The Gross Vehicle Weight Rat ing for your
Audi Q7 wo uld be exceeded if your vehi­
cle is s imultaneously equ ipped with Pan­
oramic sliding sunroof; third-row seat­
ing; trailer towing equipment (factory or
dealer-installed), and running boards
(dealer-installed). UNDER NO CIRCUM­
STANCES MAY ALL SUCH ITEMS BE IN­
STALLED ON T HE SAME VEHICLE .
- The actual Gross Axle Weight Rat ing at
the front and rear axles should not ex­
ceed the perm iss ible weights, and their
c ombination must not exceed the Gross
Vehicle Weight Rat ing.
G ene ral in formation 315
-Exceeding perm iss ible weight ratings can
result in veh icle damage, acc idents and
personal injury.
([) Note
-The ve hicle capacity weight figures apply
when the load is d istr ibuted evenly in the
vehicle (passengers and luggage). When
transport ing a heavy load in the luggage
compartment, carry the load as near to
the rear axle as poss ible so that the vehi­
cle's handling is not impaired.
- Do not exceed the maximum permissible
axle loads or the maximum gross veh icle
we ight. Always remember that the vehi­
cle's handling w ill be affected by the ex­
tra load. Therefore, ad just yo ur speed ac­
co rding ly.
- Always observe local regulat ions .
Dimensions
T he specifications refer to the basic model.
D ifferences may occur depending on the mod­
el type and op tions ordered, fo r example, tire
sizes .
Q) Note
When dr iv ing up steep ramps, on rough
r oads, over c urbs, etc. it is important to re ­
member that some parts of your vehicle,
such as spoi lers or exhaust system compo­
nents, may be close to the ground. Be
careful not to damage them.
•
•
I

316 Data
Data
280 hp, 6-cylinder engine, with all-wheel drive
Engine data Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio
Fuel
Dimensions (approx .)
Length (with license plate bracket)
Width (with outside mirrors folded) Height (unloaded)
Turning circle diameter (curb to curb)
Capacities (approx .)
Fuel tank
- Total capacity
- Reserve (of total capacity) hp@ rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm) 280@ 4900
-6500
-·--295@ 2150 -4900
6 cylinder
-·~-182 .8 (2995)
3.33 (84 .5)
3 .50 (89 .0)
--· 10.5 : 1
Premium unleaded (91 AKI) Recommended for
maximum engine performance. Further details
¢page 250, Fuel supply
in (mm) 200.3 (5089)
in (mm) 78.1 (1983)
in (mm) 68.4 (1737)
ft (m) 39 .4 (12)
gal (liters) 26.4 (100)
gal (liters) 2.6-3.2 (10 -12)
Windshield and headlight* washer fluid container quarts (liters) 4.8 (4 .5)
Engine oil with filter change quarts (liters) 8.5 (8.1)

Data
333 hp, 6-cylinder engine, with all-wheel drive
Engine data
Maximum output SAE net
Maximum torque SAE net
No. of cylinders
Displacement
Stroke
Bore
Compression ratio
Fuel
Dim ension s (appro x.)
Leng th (with license pla te bracket)
Width (with outside mirrors folded) He igh t (unloaded)
T urning circle diameter (curb to curb)
Capacit ies (appro x.)
Fuel tank
- Total capacity
- Reserve (o f total capacity) 333@ 5500 - 6500
hp@rpm
lb-ft@ rpm
-~~-
CID (cm3
)
in (mm)
in (mm)
--·
325 @ 2900 - 5300
6 cylinder
182 .8 (2995)
3 .33 (84.5)
3 .50 (89.0)
10.5 : 1
Premium unleaded (91 AKI) Recommended for
maximum engine performance. Further details
<=> page 250, Fuel supply
in (mm) 200.3 (5089)
in (mm) 78.1 (1983)
in (mm) 68.4 (1737)
ft (m) 39 .4 (12)
gal (liters) 26.4 (100)
gal (lite rs) 2 .6 -3.2 (10 -12)
Windshield and headlight* washer fluid container quarts (liters) 4 .8 (4 .5)
Engine oil with filter change quarts (liters) 8
.5 (8 .1)
317
•
•

318 Data
225 hp, 6-cylinder engine, with all-wheel drive
Applies to vehicles: with diesel engine
Engine data
Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Stroke
Bore
Compression ratio
Fuel
Dimen sions (app rox.)
Length (with license plate bracket)
Width (with outside mirrors folded)
He ight (unloaded)
Turning circle diameter (curb to curb)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of total capacity) hp@ rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm) 225@ 3750 - 4000
-·--406@ 1750 - 2250
6 cylinder
-•--
181.1 (2967)
3 .60 (91.4)
3.27 (83 .0)
~-· 16.8: 1
ULSD-Diesel No. 2 Further details
c:> page 251, Die­
sel fuel
in (mm) 200.3 (5089)
in (mm) 78.1 (1983)
in (mm) 68.4 (1737)
ft (m) 39.4 (12)
gal (liters) 26.4 (100)
gal (l iters) 2.6-3.2 (10-12)
Windshield and headlight* washer fluid container quarts (liters)
4.8 (4.5)
Engine oil with filter change quarts
(liters) 8.6 (8.2)