2012 AUDI Q7 Owner´s Manual

Tires an d wheel s 2 79
change. In the event of discrepancies, the tire
pressure label located on the driver's side 8-
p ill ar a lways takes precedence.
The table be low lists the recommended cold
tire inf lation pressures for the A udi model
I Engine Tire designation
covered by your Owner 's Literat ure at the vehi­
cle's capacity weight and the tire sizes instal­
l ed on the respect ive models as orig inal
equipment, or as a factory option.
Tire pressure
normal load condition full load condition front rear front rear
I
PSI II kPA PSI kPA PSI j[ kPA PSI kPA
2 55/5 5 Rl8 109H XL
All Sea son
265 /50 Rl9 ll0H XL
All Sea son
3.0 /3 .0 TDI 275 /45 R20 ll0H XL
6 -cy lind er All S ea son
275 /45 R20 110V XL
High Performance
295 /35 R21 107V XL
High Performance
35 240 35
35 240 35
35 240 35
35 240 35
36 250 35 240
44
300 49 340
240 44 300 49 340
240 44 300 49 340
•
240 44 300 49 340
I
240 44 300 49 340
XL= reinforced or extra load tire. It may also appear as xl, EXTRA LOAD, or RF on the tire side­
wall.
The correct tire pressure for the spare wheel i s
l ocated on a label on the driver's side 8-pilla r.
Because technical changes may be made to
vehicle equ ipment dur ing the model year , al­
ways compare the tire size designation on the
tire pressure label on your vehicle w ith the
tires on you r vehicle. Ma ke su re that the tire
si ze information on the ve hicle label is the
same as the s ize of the t ires on the vehicle.
This is especially important if the vehicle be­ l ongs to someone else or you bought the vehi­
cle with different rims/tires or you bought the
ve hicle as a previously owned vehicle.
Remember, your safety and that of your pas­
sengers also depends on making sure that
l oad limits are not exceeded. Vehicle load in­
cludes everybody and everything in and on the
vehicle. These load limits are technically refer­ red to as the vehicle's Gross Vehicle We ight
Rating ("GVWR") . The Gross Axle Weight Rat­
i ng ( "GAWR") is the maximum load that can
be appl ied at each of the veh icle's two axles.
The G ross Vehicle Weight Rating and the Gross Axle Weig
ht Rating are listed on the
safety comp liance sticker label located on the
drive r's side 8-pillar . The tire pressure labe l on
yo ur A udi lists t he maxim um combined
weight of all o f the occ upants and luggage or
othe r cargo that t he vehicle can carry. Fo r the
location of the tire press ure label ¢
fig. 23 7.
A WARNING
Overloading a vehicle can cause loss of ve­
h icle control, a crash or other accident, se­
rious personal injury, and even death.
- Carrying more we ight than your veh icle
was des igned to carry will prevent the
veh icle from handling properly and in­
crease the risk of a loss of vehicle con­
trol.
- The brakes on a vehicle that has been overloaded may not be able to stop the
veh icle w ith in a safe distance.
- T ires on a vehicle that has been overload ­
ed can fail suddenly ca using loss of con-
trol and a crash . ..,.
•
•

28 0 T ire s and wheel s
-Always make su re that t he tota l load be­
ing t ransp orted -includ ing the we ight of
a tra ile r hitch a nd the tongue weight of a
loaded trailer -does not make the veh i­
cle heav ier than the veh icle's Gross Vehi­
cl e Weight Rating.
A WARNING
- Incorrect tire pressures and/or underin­
flation can lead to a serious or fatal acci­
dent .
- Incorrect tire pressures and/o r underin­
flation cause increased tire wear and can affect the handling of the vehicle.
- Incor rect tire pressures and/or underin­
fla tion can also lead to sudden tire fa il­
ure, incl uding a b lowo ut and sudden de ­
flation, causing loss of vehicle control.
Checking tire pressure
The correct tire pressure for the tires original­
ly installed on your vehicle is listed on the tire
pressure label loc;ated on driver's side 8-pil­
lar.
The recommended t ire p ress ures are o n the
tire pressure label and in the tab le
¢ page 278, Cold tire inflation pressure.This
means that the pressure must be checked and
ad justed when the tire has not been driven for
more than a couple of m iles (kilometers) at
l ow speeds during the previous three hours.
A ir in the tires expands when the tire heats up
as a result of internal fr iction as it flexes in
use . The t ire pressure is higher when the tire
has wa rmed up than when it is "cold ."
It is the inflat ion pressure in a "cold" tire that
counts. Therefore, you should never let air out
of a warm t ire to match "Cold tire inflation
p ressu re" recommendations ¢
page 2 78. The
tires would then be under inflated and cou ld
fa il suddenly .
The t ire pressure label on you r Audi lists the
r ecommended cold t ire inflat io n pressu res at
maximum capacity fo r the new, o rigi na l
eq uipment t ires that were on your vehicle at the time
it was man ufactu red. Fo r the loca ­
tion of the labe l
~page 278, fig . 237.
Most tires lose air natur ally over t ime. They
can a lso lose some air if yo u drive over a pot­
hole or hit a curb while park ing.
It is usually
not possible to see whether the radial tires
u sed today are underinflated just by looking
at them.
The re fore, be sure to check ti re p ress ures at
least once a mo nth and a lways before going
on a long trip . Make s ure to take the n umber
of peop le and the amount of luggage into ac­
count when adjust ing tire pressure for a trip -
even one that you wou ld not consider to be
"long. " See
~ page 2 82, Tires and vehicle
load limits
for mo re important information .
Always use an accurate tire pressure gauge
when checking and adjusting inflat ion pres ­
s ur es. Check all of the tires and be sure not to
forget the spare tire .
If the pressure in any t ire
i s too high when the t ire is "cold," let air out
of the t ire s low ly w ith the edge of the tire
gauge and keep checking the pressure until
yo u reach the pressure that is correct for the
l oad (passengers and l uggage) and kind of
driv ing you plan to do.
If the pressure in any ti re is too low, note the
difference between the pressure in the co ld
tire and the pressure you need and add the air
that you need to reach the correct pressure for
the vehicle load (passengers and luggage) for
the tires on your vehicle as listed on the on
your vehicle and in this ma nual and the kind
of d riving you plan to do.
Ne ver e xceed the ma ximum infl ation pres­
sure listed on the ti re sidewall for an y rea ­
son .
Remember that the vehicle manufacturer, not
the tire manufact urer, determines the correct
t ire press ure for the tires on your vehicle.
It is important to check the ti re pressure whe n
the tires are co ld.
- Read the required tire pressure from the t ire
pressure labe l. The tire pressure label is lo -
cated o n the driver's side B-pillar . T he tire
liJJ>

pressure label lists the recommended cold
tire i nflatio n pressures for the vehicle at its
maximum capacity we ight a nd the tires that
were on your vehicle at the time it was man ­
ufactured . For recommended t ire pressures
for normal load condit ions, please see chap ­
ter ~
page 2 78 .
-Turn the valve stem cap counter-clockwise
to remove it from the tire valve .
- Place the air pressure gauge on the valve.
- The tire pressures should only be checked
and adjusted when the tires are cold . The
s light ly raised pressures of warm tires must
not be reduced .
- Adjust the tire pressure to the load you are
carrying.
- Re insta ll the va lve stem cap on the valve .
When should I check the tire pressure ?
The correct tire pressure is especially impor ­
tant at high speeds . The pressure sho uld
therefo re be checked at least once a month
and a lways before start ing a journey. Do not
forget to check the tire pressure for the spare
wheel.
When should I adju st the tire pre ssures?
Ad just the tire pressure to the load you are
carrying. After changing a wheel
or replacing
wheels you have to adjust the tire pressures
on all wheels. In addition, you must then
store the new tire pressures i n the t ire pres­
sure mon itor ing system
~ page 294.
A WARNING
Incorrect tire pressures and/or unde rinfla­
tion ca n lead sudden tire failure, loss of
cont ro l, col lision, ser ious persona l inju ry
or even death.
- Whe n the wa rning symbo l
RI] appears in
the instrument cl uster, s top an d inspect
the tires.
- Incorre ct tire pressure and/or unde rinfla­
t ion can cause inc reased t ire wear and
can affect the handling o f the veh icle and
stopp ing ability.
- Incorrect tire pressures and/or underin­
flation can also lead to sud den tire fa il-
Tires an d wheel s 281
ure, including a blowout and sudden de­
flation, ca using loss of veh icle contro l.
- The driver is responsib le for the correct
tire pressures for all tires on the veh icle.
The applicable pressure values are locat­
ed on a sticker o n the dr iver's s ide B-pil­
lar .
- Onl y when all tires on the vehicle are fil­
led to the correct pressure, the t ire pres­
sure mon itor ing system can work cor­
rectly .
- The use of incorrect tire pressure va lues
can lead to acc idents or other damage .
Therefore it is ess ential that th e drive r
observe t he spec ified t ire p ress ure val ues
for the tires and the cor rect pressures for
the func tion of the t i re p ress ure moni to r­
ing system.
- Always in flate tires to the recommen ded
a nd correct t ire p ress ure be fore dr iv ing
off .
- D riving with unde rinf lated tires bend
mo re, letting them get too hot resulting
in tread separation, s udden tire failure
and loss of control.
- Excessive speed and/overloading can
cause heat b uild- up, sudden tire failure
and loss of control.
- If the tire pressure is too low or too high,
the t ires will wear prematurely and the
veh icle w ill not handle well.
- If the tire is not flat and you do not have
to change a wheel immediately, d rive at
red uced speed to the nearest service sta­
tion to check the t ire press ure and add
air as requ ired .
(D Note
Driving w ithout valve stem caps can cause
damage to the tire valves. To prevent this,
a lways make sure that factory installed
valve s tem caps o n all whee ls are sec urely
mounted o n the valve .
@ For the sake of the environment
Underinflated tires will also increase the
fuel consumpt ion.
•
•

28 2 T ire s and wheel s
Tires and vehicle load limits
There are limits to the amount of load or
weight that any veh icle and any t ire can carry.
A vehicle that is overloaded wi ll not handle
well and is more difficult to stop. Overload ing
can not on ly lead to loss of vehicle control
,
but can a lso damage impo rtant parts of the
vehicle and can lead to sudden tire failure in-
,
eluding a blowout and sudden deflation that
can cause the veh icle to crash .
Your safety and that of your passengers a lso
depends on making sure that load limits are not exceeded. Vehicle load includes everybody
and everyth ing in and on the vehicle . These
load limits are tech nically referred to as the
vehicle 's
Gr oss Vehicl e W eig ht Rating
("GVWR").
The "GVWR" includes the we ight of the basic
vehicle, all factory installed accessories , a full
tank of fuel , oi l, coo lant and other fluids plus
maximum load. The maxim um load includes
the number of passengers that the vehicle is intended to carry ("seating capacity") with an
assumed weight of 150 lbs (68 kg) for each
passenger at a designated seating position
and the tota l weight of any l uggage in the ve­
h icle. If you tow a trailer, the weight of the
trailer h itch and the tongue weight of the
loaded trailer must be included as part of the
ve hicle load .
The
G ro ss Ax le We ight Rat ing ("GAWR") is
the maximum load that can be applied at each
of the vehicle's two axles .
The Gross Vehicle Weight Rating and the
Gross Axle Weight Rating are listed on the
safety compliance st icker label located on the
driver's side B -p illar . Your Audi has 5 seating
positions, 2 in the front and 3 i n the rear for
total seating capacity of 5. On vehicles w ith
six seats*, your veh icle has two front seats,
two seats in the second row seating and two
seats in the third row seating . On vehicles
with seven seats*, your vehicle has two front
seats, three seats in the second row seating
and two seats in the third row seating . Each seating position has a seat belt
q
page 170,
Safety belts .
The fact that there is an upper limit to yo ur
vehicle's Gross Vehicle Weight Rating means
that the total weight of whatever is being car­
ried in the vehicle (including the weight of a
trailer hitch and the tongue weight of the
loaded tra iler) is lim ited. The more passen­
gers in the vehicle or passengers who are
heavier than the standard we ights assumed
mea n that less we ight can be carr ied as lug­
gage .
The tire pressure label on your Audi also lists
the maximum combined weig ht of a ll of the
occupants and luggage or other cargo that
the vehicle can carry . Fo r the location of the
label qpage278, fig. 237.
_& WARNING
Overloading a vehicle can cause loss of ve­
h icle cont ro l, a crash or other accident, se­
rious personal injury, and even death.
- Ca rrying more we igh t than your veh icle
was des igned to carry wi ll prevent the
vehicle from handling properly and in­
crease the risk of the loss of vehicle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
veh icle w ith in a safe distance.
- Tires on a vehicle that has been over load­
ed can fail s uddenly, including a blowout
and sudden deflation, causing loss of
control and a crash .
- Always make sure that the total load be­
ing transported -including the weight of
a trailer hitch and the tongue we ight of a
loaded trailer -does not ma ke the vehi­
cle heavi er than the vehicle's Gross Vehi­
cle Weight Rating.
Determining correct load limit
U se t he exa mple b elo w t o ca l­
c ulat e th e t otal w eight of the
pa sseng ers a nd luggage or

other things that you plan to
transport so that you can make sure that your vehicle will not
be overloaded.
Steps for Determining Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF OC­
CUPANTS AND CARGO
SHOULD NEVER EXCEED XXX KG OR XXX LBS"on your vehi­
cle's placard (tire inflation
pressure label)
¢ page 2 78,
fig. 237.
2.
Determine the combined
weight of the driver and pas­ sengers that will be riding in
your vehicle.
3. Subtract the combined weight of the driver and pas­sengers from
"XXX" kilo­
grams or
"XXX" pounds
shown on the sticker
¢ page 278, fig. 237 .
4. The resulting figure equals
the available amount of car­
go and luggage load capaci­
ty . For example, if the
"XXX"
amount equals 1400 lbs.
and there will be five 150
lbs. passengers in your vehi­
cle, the amount of available
cargo and luggage load ca-
Tires and wheels 283
pa city is 650 lbs. (1400-7 so
(5 X 150) = 650 lbs.)
5. Determine the combined
weight of luggage and cargo
being loaded on the vehicle .
That weight may not safely exceed the available cargo
and luggage load capacity
calculated in Step
4.
6. If your vehicle will be towing
a trailer, load from your trail ­
er will be transferred to your
vehicle. Consult this manual
to determine how this re­
duces the available cargo
and luggage load capacity of
your vehicle.
~ Check the tire sidewall
( ¢ page 285 , fig. 241) to de­
termine the designated load rating for a specific tire.
•
•
'

284 Tires and wheels
Tire service life
The service life of tires depends on a lot of
different things including proper installation
and balancing, correct tire pressure and driv­
ing style.
Fi g. 2 39 Tire tread: tre ad wea r ind icators (TWI)
F ig. 240 Rotat ing t ires for more ev en wea r
Tread Wear Indicator (TWI)
The o rigi na l tires on your veh icle have
1/16 inch (1.6 mm) high "wear indicators"
.... N M
c::> fig . 239 running across the tread. Depend ­
i ng on the make, there will be six to eight of
them evenly p laced around the t ire. Marks on
the tire sidewa ll (for example "TWI" or other
symbols) indicate the positions of the tread
wear ind icators . Worn t ires must be replaced .
Different fig ures may apply in o ther countries
c::> & .
Tire p res sure
Incorrect tire pressure causes premature wear
a nd can cause sudden t ire blow-out. For th is
reason, tire pressure must be checked at least
once a month
c::> page 280.
Driving style
Driving fast aro und curves, heavy acce leration
and hard braking increase tire wear.
Rotating tires for more even wear
F or all four tires on your ve hicl e to h ave the
same service life, we recommend that the
front and rear t ires are rotated according to
the tire manufacturer's suggested tire rota­
tion intervals. Please remember the follow­
ing :
- Tire rotation intervals may differ from the
vehicle service inte rva ls o utlined in your
Warranty
& Maintenance booklet .
- The longer one tire is used in one location
on the vehicle, the more it wears at certain
points; therefore, we recommend that you
follow the tire manufact urer's suggested
tire rotation intervals .
- Vehi cles w ith front-wheel dr ive experience
more tread wear on the front wheels com­
pa red to all-wheel drive (quattro ®).
- Please rotate tires as shown
c::> fig. 240.
-Extra care must be taken when rotating di-
rection-specific tires
c::> page 302 .
Wheel balancing
The wheels on new ve hicles are balanced .
However, various situations during everyday
driving can cause them to become unbal ­
anced, re sulting in vibrat ions you can usually
feel through the steer ing wheel.
Un balanced whee ls must be rebalanced to
avoid excessive wear on steering, suspension
and t ires. A whee l must also be reba lanced
when a new tire is insta lled.
Incorrect wheel alignment
Incor rect wheel alig nment can cause exces ­
sive tire wear, impairing the safety of the veh i­
cle . If tires show excessive wear, have the
whee l alignment checked by an authori zed
Audi dealer or qualif ied workshop .
All-wheel driv e
Vehicles with q uattro ® mus t always have tires
of the same size, construction and tread type .
For details see
c::> page 225. ..,.

A WARNING
Sudden tire failure can lead to loss of con­
trol, a crash and serious personal injury!
- Never drive a vehicle when the tread on
any tire is worn down to the wear indica­
tors.
- Worn tires are a safety hazard, they do
not grip well on wet roads and increase
your risk of "hydroplaning" and loss of
control.
- Always keep chemicals that can cause
tire damage, such as grease, oil, gasoline
and brake fluid away from t ires.
- Tires age even if they are not be ing used
and can fail suddenly, especially at high
speeds . Tir es that are more than 6 years
old can only be used in an emergency
and then with special care and at lower
speeds.
- Never mount used tires on your vehicle if
you are not sure of their" previous histo ­
ry ." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss of vehicle control.
Tires and wheels 285
New tires and replacing tires and wheels
New tires and wheels have to be broken in .
Fig. 241 Tir e specificat ion codes on t he s idewall o f a
tire
No. Description
CD Passenger car tire (where applicable)
@ Nominal width of tire in millimeters
® Ratio of height to width (aspect ratio)
© Radial
® Rim diameter code
® Load index and speed rat ing
(f) U.S. DOT tire identification number
® Audi Original tire
® Sever snow conditions
@ Tire ply composition and materials
used
@ Maximum load rating
@ Treadwear, traction and temperature
grades
@ Maximum permissible inflation pres-
sure
The tires and rims are essential parts of the
vehicle's design . The tires and rims approved
by Audi are specially matched to the charac­
teristics of the vehicle and can make a major .,.
•

286 Tires and wheels
contribution to good road ho lding and safe
handling when in good condition and properly
inflated
¢ ,& .
We recommend that all work on tires and
wheels be performed by an authorized Audi
dealer. They are familiar with recommended
procedures and have the necessary spec ial
too ls and spare parts as well as the proper fa­
cilities for disposing of the old tires.
Authorized Audi dealers have the necessary information about technical requ irements for
installing or changing tires and r ims.
Replacing tires and wheels
Tires should be rep laced at least in pairs and
not individually (for example both front tires
or both rear tires together).
Be sure to read and heed the information to
the tire pressure monitoring system
¢pa ge 292.
Always buy rep lacement radial tires that have
the same specifications as the tires approved
for your vehicle by Audi. Replacement t ires
must always have the same load rating speci­
fication as the original equipment or approved
optional tires listed in the table
c:> page 2 78.
Aud i-approved specification ti res are specially
matched to your vehicle and its load limits,
and can contribute to the important road hold­
ing, driving characteristics, and safety of the
vehicle. The table
(c:> page 2 78) lists specifica­
tions of the tires approved for the Audi mod­
els covered by your Owner's Literature .
The tire pressure label located on the driver's
side B-pillar
c:> page 2 78, fig. 238 lists the
specifications of the original equipment tires
installed on your vehicle at the time it was
manufactured.
Federal law requires tire manufacturers to
place standard ized information on the s ide­
wall of all tires
c:> fig. 241 . This information
identifies and describes the fundamental
characterist ics, the quality grade of the tire
and also provides a tire ident ificat ion number f
or sa fety standard certification and in case of
a reca ll.
Tire specifications
Knowledge of tire specificat ions makes it eas­
ier to choose the correct tires. Radial tires
have the tire specifications marked on the
sidewa ll, for examp le:
P255 / 55 R 18 109 H XL
This conta ins the following information:
P Indicates the tire is for passenger cars
(where app licab le)
255 Nominal tire width in mm of the tire
from sidewall edge to sidewall edge. In
general, the larger the number, the wider
t he tire
55 Height/width ratio in percent (aspect ra-
t io)
R Tire construction: Radial
18 Rim diameter code (in inches)
109 Load rating code
H Speed rat ing letter code
XL (or "xl", "EXTRA LOAD", or "RF" Indicates
that the tir e is a"Re inforced" or an "Extra
Load " tir e
M+S (or "M/S") Indicates that the tire has
some mud and snow capability
The tires could also have the information of
direction of rotat ion
c:> page 274 .
Tire manufacturing date
The manufacturing date is also indicated on
the tire sidewall (possibly on ly on the
inner
side of the wheel):
"DOT ... 2211. .. " means, for examp le, that
the tire was produced in the 22nd week of
2011.
Speed rating (letter code)
The speed rating letter code on the whee ls in­
dicates the maximum permissible road speeds
c:> & in Winter tires on page 290 .
P up to 93 mph (150 km/h)
Q up to 99 mph (158 km/h)
R up to 106 mph ( 170 km/h)