2011 TOYOTA AURIS Owners Manual (in English)

225 2-4. Using other driving systems
2
When driving
UK_AURIS_HV_EE
CAUTION
When using the Toyota parking assist-sensor
Observe the following precautions.
Failing to do so may result in the vehicle being unable to be driven safely
and possibly cause an accident.
Do not use the sensor at speeds in excess of 10 km/h (6 mph).
Do not attach any accessories within the sensor range.
NOTICE
When washing the vehicle
Do not apply intensive bursts of water or steam to the sensor area.
Doing so may result in the sensor malfunctioning.

226
2-4. Using other driving systems
UK_AURIS_HV_EE
Rear view monitor system
: If equipped
The rear view monitor system assists the driver by displaying an
image of the area behind the vehicle. The image is displayed in
reverse on the screen. This reversed image is a similar image to the
one on the inside rear view mirror.
The rear view image is dis-
played when the shift position
is in R.
The screen is turned off if any
one of the following conditions
are met:
• The shift position is
changed out of R
• The screen remains on for 5
minutes

227 2-4. Using other driving systems
2
When driving
UK_AURIS_HV_EERear view monitor guide lines
Guide lines are displayed on the screen.
The guide lines may look differently depending on vehicle orientation or
road conditions.
Vehicle width extension guide lines (blue)
These lines indicate the estimated vehicle width extension.
Distance guide line (blue)
This line indicates a position on the ground about 1 m (3 ft.) behind on the
ground of the rear bumper of your vehicle.
Distance guide line (red)
This line indicates a position on the ground about 0.5 m (1.5ft.) behind on
the ground of the rear bumper of your vehicle.
Vehicle center guide lines (blue)
These lines indicate the estimated vehicle center on the ground.
The rear view monitor system can be operated when
The shift position is in R and the “POWER” switch is in ON mode.

228 2-4. Using other driving systems
UK_AURIS_HV_EE
Switching the screen ON/OFF mode
Displayed area
When the screen is displayed, press
on the inside rear view mirror to
switch the screen ON/OFF mode.
Screen ON mode: Green indicator comes
on.
Screen OFF mode: Amber indicator
comes on.
The auto anti-glare inside rear view mir-
ror will revert to the screen ON mode
each time the “POWER” switch is in the
ON mode.
The area covered by the camera is lim-
ited. Objects that are close to either cor-
ner of the bumper or under the bumper
cannot be seen on the screen.
The area displayed on the screen may
vary according to vehicle orientation or
road conditions.
Corners of bumper

229 2-4. Using other driving systems
2
When driving
UK_AURIS_HV_EE
Rear view monitor system camera
The rear view monitor system camera is
located on the back door as shown in the
illustration. The camera uses a special
lens. The distance of the image that
appears on the screen differs from the
actual distance.
In the following cases, it may become dif-
ficult to see the images on the screen,
even when the system is functioning cor-
rectly.
The vehicle is in a dark area, such
as at night.
The temperature near the lens is
extremely high or low.
Water droplets are on the camera
lens or humidity is high, such as
when it rains.
Foreign matter, such as snow or
mud, adheres to the camera lens.
When the camera has scratches or
dirt on it.
The sun or headlights are shining
directly into the camera lens.
A bright object such as a white wall
is reflected in the mirror surface
over the monitor.

230 2-4. Using other driving systems
UK_AURIS_HV_EE
Smear effect
Flicker effect
When the camera is used under fluorescent light, sodium lights, or mercury
lights etc., the lights and the illuminated areas may appear to flicker.
If a bright light, such as sunlight reflected
off the vehicle body, is picked up by the
camera, a smear effect* characteristic to
the camera may occur.
*: Smear effect: A phenomenon that
occurs when a bright light is picked up
by the camera; when transmitted by
the camera, the light source appears to
have a vertical streak above and below
it.

231 2-4. Using other driving systems
2
When driving
UK_AURIS_HV_EE
CAUTION
When using the rear view monitor system, observe the following pre-
cautions to avoid an accident that could result in death or serious inju-
ries.
Never depend solely on the monitor system when reversing.
Always check visually and with the mirrors to confirm your intended path is
clear.
Use your own eyes to confirm the vehicle’s surroundings, as the displayed
image may become faint or dark, and moving images will be distorted, or
not entirely visible when the outside temperature is low. When backing up,
be sure to check behind and all around the vehicle visually and with the
mirrors before proceeding.
Always check the vehicle surrounding area, because the guide lines are
ancillary lines.
The guide lines are ancillary lines and do not change even if the steering
wheel is turned.
Depicted distances between objects and flat surfaces differ from actual
distances.
Do not use the system if the back door open.
Conditions which may affect the rear view monitor system
If the back of the vehicle has been hit, the camera’s position and mounting
angle may have changed. Have the vehicle inspected by any authorized
Toyota dealer or repairer, or another duly qualified and equipped profes-
sional.
Rapid temperature changes, such as when hot water is poured on the
vehicle in cold weather, may cause the system to function abnormally.
If the camera lens is dirty, it cannot transmit a clear image. Rinse with
water and wipe with a soft cloth. If extremely dirty, wash with a mild
cleanser and rinse.
The displayed image may be darker and moving images may be slightly
distorted when the system is cold.
Caution while driving in reverse
Do not change modes while the vehicle is moving.

232 2-4. Using other driving systems
UK_AURIS_HV_EE
NOTICE
Camera precautions
As the camera has a water proof construction, do not detach, disassemble
or modify it. This may cause incorrect operation.
Do not subject the camera to a strong impact.
If the camera lens becomes dirty, it cannot transmit a clear image. If water
droplets, snow, or mud adhere to the lens, rinse with water and wipe with a
soft cloth. If the lens is extremely dirty, wash it with a mild cleanser and
rinse. Do not rub hard.
Do not allow organic solvent, car wax, window cleaner or glass coat to
adhere to the camera. If this happens, wipe it off as soon as possible. Do
not rub hard.
When replacing tires, please consult any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional. If you
replace the tires, the area displayed on the screen may change.