2011 INFINITI QX56 display

RSU-6
< PERIODIC MAINTENANCE >
WHEEL ALIGNMENT
WHEEL ALIGNMENT
InspectionINFOID:0000000006225661
DESCRIPTION
Measure wheel alignment under unladen conditions.
NOTE:
“Unladen conditions” means that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
PRELIMINARY CHECK
Check the following:
 Tires for improper air pressure and wear
 Road wheels for runout. Refer to WT-64, "
Inspection".
 Wheel bearing axial end play. Refer to RAX-5, "
Inspection".
 Ball joint axial end play of suspension arm and front lower link. Refer to RSU-20, "
Ball Joint".
 Shock absorber operation
 Each mounting point of axle and suspension for looseness and deformation
 Each of front lower link, rear lower link, rear suspension member, suspension arm and shock absorber for
cracks, deformation, and other damage
 Vehicle height (posture)
GENERAL INFORMATION AND RECOMMENDATIONS
 A four-wheel thrust alignment should be performed.
- This type of alignment is recomm ended for any NISSAN/INFINITI vehicle.
- The four-wheel “thrust” process helps ensure that t he vehicle is properly aligned and the steering wheel is
centered.
- The alignment rack itself should be capable of accepting any NISSAN/INFINITI vehicle.
- The rack should be checked to ensure that it is level.
 Make sure the machine is properly calibrated.
- Your alignment equipment should be regularly calib rated in order to give correct information.
- Check with the manufacturer of your specific equi pment for their recommended Service/Calibration Sched-
ule.
ALIGNMENT PROCESS
IMPORTANT:
Use only the alignment specifications listed in this Service Manual.
 When displaying the alignment settings, many alignment machines use “indicators”: (Green/red, plus or
minus, Go/No Go). Never use these indicators.
- The alignment specifications programmed into your machine that operate these indicators may not be cor-
rect.
- This may result in an ERROR.
 Some newer alignment machines are equipped with an optional “Rolling Compensation” method to “com- pensate” the sensors (alignment targets or head units). Never use this “Rolling Compensation” method.
- Use the “Jacking Compensation Method”. After installi ng the alignment targets or head units, raise the vehi-
cle and rotate the wheels 1/2 turn both ways.
- See Instructions in the alignment machine you're using for more information on this.
AdjustmentINFOID:0000000006225662
CAMBER
Revision: 2010 May2011 QX56

SYSTEMSBC-9
< SYSTEM DESCRIPTION >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
PRE-CRASH SEAT BELT SYSTEM : Fail SafeINFOID:0000000006237879
 When a system malfunction is detected, deactivates a part of the system or all functions depending on the
malfunctioning part.
 When the malfunction condition recovers to the norma l condition, the system returns to the normal opera-
tion.
*1: The deactivation mode differs depending on the internal malfunctioning condition of control unit Display contents of CONSULT-III Fail-safe
U0126 STRG ANG SEN SIG Stops the operation in the conditions as per the following.
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 A part of comfort function
U0428 STRG ANGL CAL Stops the operation in the conditions as per the following.
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 A part of comfort function
U1000 CAN communication circuit Stops the operation in the conditions as per the following. *
1
 During emergency brake operation
 When ABS continuously operates
 When lateral slippage during cornering occurs
 When Intelligent brake assistance operates
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2451 SEAT BLT MTR DR CIRC Fully deactivates the whole operation.
B2452 SEAT BLT MTR AS CIRC Deactivate s a part of comfort function.
B2453 BR_STROKE_SEN_CIRC Stops the operation in the conditions as per the following.
 During emergency brake operation
 When ABS continuously operates
 A part of comfort function
B2454 SEAT BLT PWR DR CIRC Fully deactivates the whole operation.
B2455 CONTROL UNIT DR Stops the operation in the conditions as per the following. *
1
 During emergency brake operation
 When ABS continuously operates
 When lateral slippage during cornering occurs
 When Intelligent brake assistance operates
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2456 SEAT BLT PWR AS Deactivates a part of comfort function.
B2457 CONTROL UNIT AS Deactivates a part of comfort function.
B2458 LOCAL COMM Deactivates a part of comfort function.
B2461 VHCL SPEED SIGNAL Stops the operation in the conditions as per the following.
 During emergency brake operation
 When ABS continuously operates
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 When comfort function operates
B2463 ROLLOVER SIGNAL Stops the operation in the conditions as per the following.
 When the vehicle inclined excessively
 A part or the whole comfort function
B2466 DR/AS CONTROL UNIT Deactivates a part of comfort function.
B2470 SYS HEAT PROTC DR  Fully deactivates the whole operation.
 Operation return
- 1 time operation becomes possible after approximately 30 seconds
- Returns to the initial condition after approximately 8 minutes
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (PRE-CRASH SEAT BELT)SBC-11
< SYSTEM DESCRIPTION >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
DIAGNOSIS SYSTEM (P RE-CRASH SEAT BELT)
CONSULT-III FunctionINFOID:0000000006237882
Diagnosis for pre-crash seat belt syst em can be performed using CONSULT-III.
APPLICATION ITEM
SELF-DIAGNOSIS RESULTS
Refer to SBC-16, "DTC Index".
CAUTION:
When malfunctions are detect ed in several systems, includin g CAN communication [U1000], trouble-
shoot CAN communication [U1000].
A malfunction of system may be disp layed when battery voltage is low (when 7 to 8 V is continued for
approximately 2 seconds) even though the system is not malfunctioning. Erase DTC memory and
never replace any parts after making sure that the syst em is normal, especially if the malfunctions are
displayed after replacing battery.
ERASING SELF-DIAGNOSIS RESULTS
 SELF-DIAGNOSIS RESULTS Current “SELF-DIAG RESULTS” are displayed. (If all suspect circuits have been repaired, “NO DTC” is dis-
played.)
DATA MONITOR
Part to be diagnosed Diagnosis Mode Function description
Pre-crash seat belt Self-diagnosis Results
 Displays data recorded when a malfunction is de-
tected.
 Erases DTC recorded in memory.
Data Monitor Displays input data for pre-crash seat belt control
unit in real time.
Work Support Changes the setting for each system function.
CAN DIAG SUPPORT MNTR Monitors communication status of CAN communi-
cation.
Ecu Identification Displays pre-crash seat belt control unit part num-
ber.
Monitor item Contents
BUCKLE SW RH Indicates [ON/OFF] condition of seat belt buckle switch (RH).
BUCKLE SW LH Indicates [ON/OFF] condition of seat belt buckle switch (LH).
VEHICLE DISTANCE Indicates [ON/OFF] condit ion of intelligent brake assist signal.
IGN SW Indicates [ON/OFF] condition of ignition switch.
FR DOOR SW RH Indicates [Close/Open] condition of front door switch (RH).
FR DOOR SW LH Indicates [Close/Open] condition of front door switch (LH).
ABS ACTIVATING Indicates [ON/OFF] co ndition of ABS operation signal.
VHCL SPEED Indicates [Km/h] vehicle speed signal.
BRK PEDAL SNSR1 Indicates [V] voltage of brake pedal stroke sensor 1 signal.
BRK PEDAL SNSR2 Indicates [V] voltage of brake pedal stroke sensor 2 signal.
STRG ANGLE Indicates [deg] steering angle signal.
STRG ANGLE SPEED Indicates [deg/s] steering angle speed signal.
INCLINATION JDMT Indicates [ON/OFF] condition of pre roll over signal.
PRE-TEN ACTIVTN Indicates [ON/OFF] condition of pre-tensioner operated signal.
HEAT PROTC RH Indicates [ON/OFF] condition of heat protection (RH).
HEAT PROTC LH Indicates [ON/OFF] condition of heat protection (LH).
Revision: 2010 May2011 QX56

PRE-CRASH SEAT BELT CONTROL UNIT (DRIVER SIDE)SBC-15
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
*1: The deactivation mode differs depending on the internal malfunctioning condition of control unit Display contents of CONSULT-III Fail-safe
U0126 STRG ANG SEN SIG Stops the operation in the conditions as per the following.
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 A part of comfort function
U0428 STRG ANGL CAL Stops the operation in the conditions as per the following.
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 A part of comfort function
U1000 CAN communication circuit Stops the operation in the conditions as per the following. *
1
 During emergency brake operation
 When ABS continuously operates
 When lateral slippage during cornering occurs
 When Intelligent brake assistance operates
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2451 SEAT BLT MTR DR CIRC Fully deactivates the whole operation.
B2452 SEAT BLT MTR AS CIRC Deactivate s a part of comfort function.
B2453 BR_STROKE_SEN_CIRC Stops the operation in the conditions as per the following.
 During emergency brake operation
 When ABS continuously operates
 A part of comfort function
B2454 SEAT BLT PWR DR CIRC Fully deactivates the whole operation.
B2455 CONTROL UNIT DR Stops the operation in the conditions as per the following. *
1
 During emergency brake operation
 When ABS continuously operates
 When lateral slippage during cornering occurs
 When Intelligent brake assistance operates
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2456 SEAT BLT PWR AS Deactivates a part of comfort function.
B2457 CONTROL UNIT AS Deactivates a part of comfort function.
B2458 LOCAL COMM Deactivates a part of comfort function.
B2461 VHCL SPEED SIGNAL Stops the operation in the conditions as per the following.
 During emergency brake operation
 When ABS continuously operates
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 When comfort function operates
B2463 ROLLOVER SIGNAL Stops the operation in the conditions as per the following.
 When the vehicle inclined excessively
 A part or the whole comfort function
B2466 DR/AS CONTROL UNIT Deactivates a part of comfort function.
B2470 SYS HEAT PROTC DR  Fully deactivates the whole operation.
 Operation return
- 1 time operation becomes possible after approximately 30 seconds
- Returns to the initial condition after approximately 8 minutes
Revision: 2010 May2011 QX56

SBC-16
< ECU DIAGNOSIS INFORMATION >
PRE-CRASH SEAT BELT CONTROL UNIT (DRIVER SIDE)
DTC Index
INFOID:0000000006237885
DTC Trouble diagnosis name
(CONSULT-III display) DTC detection condition Reference
U0126 STRG ANG SEN SIG Steering angle sensor malfunction is received SBC-33
U0428 STRG ANGL CAL Steering angle sensor calibration incomplete signal is receivedSBC-34
U1000 CAN COMM CIRCUITPre-crash seat belt control unit cannot transmit and receive CAN
communication signal for 2 seconds or more SBC-35
B2451 SEAT BLT MTR DR CIRC Motor or control unit malfunction
 Seat belt motor circuit is open or shorted
SBC-36
B2452 SEAT BLT MTR AS CIRC Motor or control unit malfunction
 Seat belt motor circuit is open or shorted SBC-37
B2453 BR_STROKE_SEN_CIRC
 Brake pedal stroke sensor malfunction
 Brake pedal stroke sensor circuit is open or shorted SBC-38
B2454 SEAT BLT PWR DR CIRC Motor power su
pply circuit is open or shortedSBC-41
B2455 CONTROL UNIT DR Malfunction in pre-crash seat belt control unit SBC-42
B2456 SEAT BLT PWR AS CIRC Motor power supply circuit is open or shortedSBC-43
B2457 CONTROL UNIT AS Malfunction in pre-crash seat belt control unit SBC-44
B2458 LOCAL COMM Local communication line open or shortedSBC-45
B2461 VHCL SPEED SIGNAL Vehicle speed signal malfunction is received SBC-47
B2463 ROLLOVER SIGNAL Rollover signal malfunction is received SBC-48
B2466 DR/AS CONTROL UNIT Control unit is out of the vehicle specificationSBC-49
B2470 SYS HEAT PROTC DRDeactivation for cooling to prevent system heating due to continuous
operation SBC-50
B2471 SYS HEAT PROTC ASDeactivation for cooling to prevent system heating due to continuous
operation
SBC-51
Revision: 2010 May2011 QX56

PRE-CRASH SEAT BELT CONTROL UNIT (PASSENGER SIDE)
SBC-17
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G
I
J
K L
M A
B
SBC
N
O P
PRE-CRASH SEAT BELT CONTROL UNIT (PASSENGER SIDE)
Reference ValueINFOID:0000000006237886
TERMINAL LAYOUT
PHYSICAL VALUES
Fail SafeINFOID:0000000006237887
 When a system malfunction is detected, deactivates a part of the system or all functions depending on the
malfunctioning part.
 When the malfunction condition recovers to the norma l condition, the system returns to the normal opera-
tion.
JMHIA0711ZZ
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(Y) Ground Power supply Input — Battery voltage
6
(LG/B) Ground Seat belt buckle switch signal Input Seat belt is fastened 0 V
Seat belt is unfastened 5 V
8
(G) Ground Local Communication Line 2 Input/
Output IGN ON 5 V
9
(–) Ground Shield — — —
16
(W) Ground Local Communication Line 1
Input/
Output ——
18
(B) Ground Ground — — 0 V
19
(W) Ground Motor passenger circuit power supply Input — Battery voltage
20
(B) Ground Motor passenger circuit ground — — 0 V
Display contents of CONSULT-III Fail-safe
U0126 STRG ANG SEN SIG Stops the operation in the conditions as per the following.
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
U0428 STRG ANGL CAL Stops the operation in the conditions as per the following.
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
Revision: 2010 May2011 QX56

SBC-18
< ECU DIAGNOSIS INFORMATION >
PRE-CRASH SEAT BELT CONTROL UNIT (PASSENGER SIDE)
*1: The deactivation mode differs depending on the internal malfunctioning condition of control unit
U1000 CAN communication circuit
Stops the operation in the conditions as per the following. *
1
 During emergency brake operation
 When ABS continuo
usly operates
 When lateral slippage during cornering occurs
 When Intelligent brake assistance operates
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2452 SEAT BLT MTR AS CIRC Fully deactivates the whole operation.
B2453 BR_STROKE_SEN_CIRC Stops the operation in the conditions as per the following.
 During emergency brake operation
 When ABS continuo
usly operates
B2455 CONTROL UNIT DR Stops the operation in the conditions as per the following. *
1
 During emergency brake operation
 When ABS continuo
usly operates
 When lateral slippage during cornering occurs
 When Intelligent brake assistance operates
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2456 SEAT BLT PWR AS Fully deactivates the whole operation.
B2457 CONTROL UNIT AS Fully deactivates the whole operation.*
1
B2458 LOCAL COMM
Fully deactivates the whole operation.*1
B2461 VHCL SPEED SIGNALStops the operation in the conditions as per the following.
 During emergency brake operation
 When ABS continuo
usly operates
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2463 ROLLOVER SIGNAL When the vehicle inclined excessively
B2466 DR/AS CONTROL UNIT Stops the operation in the conditions as per the following.
 During emergency brake operation
 When ABS continuo
usly operates
 When lateral slippage during cornering occurs
 When steering wheel is rotated for emergency
 When the vehicle inclined excessively
 A part or the whole comfort function
B2471 SYS HEAT PROTC AS  Fully deactivates the whole operation.
 Operation return
- 1 time operation becomes possible after approximately 30 seconds
- Returns to the initial condition after approximately 8 minutes
Display contents of CONSULT-III Fail-safe
Revision: 2010 May2011 QX56

U0126 ST ANG SEN SIGSBC-33
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
DTC/CIRCUIT DIAGNOSIS
U0126 ST ANG SEN SIG
DescriptionINFOID:0000000006237891
Inputs the steering angle signal from steering angle sensor via CAN communication.
DTC LogicINFOID:0000000006237892
DTC DETECTION LOGIC
NOTE:
If DTC U0126 is displayed with DTC U1000, first per form the trouble diagnosis for DTC U1000. Refer to SBC-
35, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-33, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237893
1.CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Check “Self-diagnostic result” for “ABS” with CONSULT-III. Refer to BRC-40, "
CONSULT-III Function".
Is DTC detected?
YES >> Repair or replace malfunctioning parts.
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
U0126 ST ANG SEN SIG Receipt of a malfunction signal of Steering angle signal Steering angle sensor
Revision: 2010 May2011 QX56