2011 INFINITI QX56 display

SBC-34
< DTC/CIRCUIT DIAGNOSIS >
U0428 STRG ANGL CAL
U0428 STRG ANGL CAL
DescriptionINFOID:0000000006237894
Inputs the steering calibration incomplete signal from steering angle sensor via CAN communication.
DTC LogicINFOID:0000000006237895
DTC DETECTION LOGIC
NOTE:
If DTC U0428 is displayed with DTC U0126, first perform the trouble diagnosis for DTC U0126. Refer to SBC-
33, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-34, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237896
1.CHECK DTC WITH “ABS ACTUATOR A ND ELECTRIC UNIT (CONTROL UNIT)”
Check “Self-diagnostic result” for “ABS” with CONSULT-III. Refer to BRC-40, "
CONSULT-III Function".
Is DTC detected?
YES >> Repair or replace malfunctioning parts.
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
U0428 STRG ANGL CAL Receipt of the calibration incomplete signal Steering angle sensor calibration incomplete
Revision: 2010 May2011 QX56

SBC-36
< DTC/CIRCUIT DIAGNOSIS >
B2451 SEAT BLT MTR DR CIRC
B2451 SEAT BLT MTR DR CIRC
DTC LogicINFOID:0000000006237899
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-36, "Diagnosis Procedure".
NO >> Driver side pre-crash seat belt motor system is normal.
Diagnosis ProcedureINFOID:0000000006237900
1.INSPECTION START
1. Check “Self-diagnostic result” with CONSULT-III.
2. Touch “ERASE”.
3. Perform DTC Confirmation Procedure. Refer to SBC-36, "
DTC Logic".
Is DTC B2451 displayed again?
YES >> Replace pre-crash seat belt control unit (driver side). Refer to SB-6, "SEAT BELT RETRACTOR :
Removal and Installation".
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
B2451 SEAT BLT MTR DR CIRC Circuit of seat belt
motor (driver side) is
open or shorted Pre-crash seat belt control unit (driver side)
Revision: 2010 May2011 QX56

B2452 SEAT BLT MTR AS CIRCSBC-37
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
B2452 SEAT BLT MTR AS CIRC
DTC LogicINFOID:0000000006237901
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-37, "Diagnosis Procedure".
NO >> Passenger side pre-crash seat belt motor system is normal.
Diagnosis ProcedureINFOID:0000000006237902
1.INSPECTION START
1. Check “Self-diagnostic result” with CONSULT-III.
2. Touch “ERASE”.
3. Perform DTC Confirmation Procedure. Refer to SBC-37, "
DTC Logic".
Is DTC B2452 displayed again?
YES >> Replace pre-crash seat belt control unit (passenger side). Refer to SB-6, "SEAT BELT RETRAC-
TOR : Removal and Installation".
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
B2452 SEAT BLT MTR AS CIRC Circuit of seat belt motor (passenger side)
is open or shorted Pre-crash seat belt control unit (passenger
side)
Revision: 2010 May2011 QX56

SBC-42
< DTC/CIRCUIT DIAGNOSIS >
B2455 CONTROL UNIT DR
B2455 CONTROL UNIT DR
DTC LogicINFOID:0000000006237908
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-42, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237909
1..INSPECTION START
1. Check “Self-diagnostic result” with CONSULT-III.
2. Touch “ERASE”.
3. Perform DTC Confirmation Procedure. See SBC-42, "
DTC Logic".
Is DTC B2455 displayed again?
YES >> Replace pre-crash seat belt control unit (driver side).
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
B2455 CONTROL UNIT DR Pre-crash seat belt control unit (driver side) inter-
nal circuit malfunction Pre-crash seat belt control unit (driver side)
Revision: 2010 May2011 QX56

SBC-44
< DTC/CIRCUIT DIAGNOSIS >
B2457 CONTROL UNIT AS
B2457 CONTROL UNIT AS
DTC LogicINFOID:0000000006237912
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-44, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237913
1..INSPECTION START
1. Check “Self-diagnostic result” with CONSULT-III.
2. Touch “ERASE”.
3. Perform DTC Confirmation Procedure. See SBC-44, "
DTC Logic".
Is DTC B2457 displayed again?
YES >> Replace pre-crash seat belt control unit (passenger side).
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
B2457 CONTROL UNIT AS Pre-crash seat belt control unit (passenger side) in-
ternal circuit malfunction Pre-crash seat belt control unit (passenger
side)
Revision: 2010 May2011 QX56

B2461 VHCL SPEED SIGNALSBC-47
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
B2461 VHCL SPEED SIGNAL
DescriptionINFOID:0000000006237916
Inputs the vehicle speed signal from combination meter via CAN communication.
DTC LogicINFOID:0000000006237917
DTC DETECTION LOGIC
NOTE:
If DTC B2461 is displayed with DTC U1000, first per form the trouble diagnosis for DTC U1000. Refer to SBC-
35, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-47, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237918
1.CHECK COMBINATION METER
Check combination meter. Refer to MWI-57, "
Work flow".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning parts.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC De tection Condition Possible causes
B2461 VHCL SPEED SIGNAL Receipt of a malfunction signal of the vehicle speed signal Combination meter
Revision: 2010 May2011 QX56

SBC-48
< DTC/CIRCUIT DIAGNOSIS >
B2463 ROLLOVER SIGNAL
B2463 ROLLOVER SIGNAL
DescriptionINFOID:0000000006237919
Inputs the rollover signal from air bag diagnosis sensor unit via CAN communication.
DTC LogicINFOID:0000000006237920
DTC DETECTION LOGIC
NOTE:
If DTC B2463 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SBC-
35, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-48, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237921
1.CHECK DTC WITH AIR BAG DIAGNOSIS SENSOR UNIT
Check “self-diagnostic result” for “AIR BAG DIAGNO SIS SENSOR UNIT” with CONSULT-III. Refer to SRC-19,
"CONSULT-III Function".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace air bag diagnosis sensor unit. Refer to SR-26, "
Removal and Installation".
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC De tection Condition Possible causes
B2463 ROLLOVER SIGNAL Receipt of a malfunction signal of the rollover signal Air bag diagnosis sensor unit
Revision: 2010 May2011 QX56

SBC-50
< DTC/CIRCUIT DIAGNOSIS >
B2470 SYS HEAT PROTC DR
B2470 SYS HEAT PROTC DR
DescriptionINFOID:0000000006237924
When fastening and unfastening seat belt or opening and closing door is repeated continuously for a short
period of time, the system temporarily deactivates the retracting function of seat belt to prevent excessive
heating. The system recovers automatically.
DTC LogicINFOID:0000000006237925
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-50, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237926
1.CHECK THE VEHICLE CONDITION WITH CONSULT-III DATA MONITOR
1. Check “HEAT PROTC LH” in “D ATA MONITOR” with CONSULT-III.
2. Wait until “OFF” appears.
3. Perform the “self-diagnosis result” with CONSULT-III, after performing the check.
4. Touch “ERASE”.
5. Perform DTC Confirmation Procedure. Refer to SBC-50, "
DTC Logic".
Is DTC B2470 displayed again?
YES >> GO TO 2.
NO >> INSPECTION END
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
B2470 SYS HEAT PROTC DR Deactivate s to prevent excessive heating Comfort function activates continuously in a
short period of time.
Revision: 2010 May2011 QX56