2011 HONDA ODYSSEY Owners Manual

Place the child seat on the vehicle
seat, then attach the seat to the
lower anchors according to the
child seat maker’s instructions.
Some LATCH-compatible seats
have a rigid-type connector as
shown above.
The lower anchors are located
between the seat-back and seat
bottom, and are to be used only with
a child seat designed f or use with
LATCH.
The location of each lower anchor is
indicated by a small button above the
anchor point. Your vehicle is equipped with
LATCH (Lower Anchors and
Tethers f or CHildren) at each of the
second and third row seats, and the
second row center seat (except LX
models).
Make sure there are no objects
near the anchors that could
prevent a secure connection
between the child seat and the
anchors. Move the seat belt buckle or
tongue away f rom the lower
anchors.
To install a LATCH-compatible child
seat in either outer second row seat:
1.
2. 3.
Installing a Child Seat with
LATCH
Installing a Child Seat
Using t he Out er L A T CH
46
LOWER
ANCHORS BUTTON
Rigid type
10/07/17 09:40:26 31TK8600_051
2011 Odyssey

Whatever type you have, f ollow
the child seat maker’s instructions
f or adjusting or tightening the f it.
Other LATCH-compatible seats have
a f lexible-type connector as shown
above.
Lif t the head restraint (see page
), then route the tether strap
through the legs of the head
restraint and over the seat-back,
making sure the strap is not
twisted. Attach the tether strap hook to the
tether anchor, then tighten the
strap as instructed by the child
seat maker.
Push and pull the child seat
f orward and f rom side-to-side to
verify that it is secure. If the tether strap is too long and
cannot be tightened f irmly, f ind a
route where the strap can be
tightened securely.
4. 5.
6.
7.
179
CONT INUED
Installing a Child Seat
Driver and Passenger Saf ety
47
ANCHOR TETHER
STRAP HOOK
TETHER STRAP
Flexible type
10/07/17 09:40:35 31TK8600_052
2011 Odyssey

Lif t the head restraint (see page), then route the tether strap
through the legs of the head
restraint and over the seat-back,
making sure the strap is not
twisted.
Attach the attaching clip to the
anchor fitting, then tighten the
strap as instructed by the child
seat maker.
Unlatch the detachable seat belt
anchor latch and retract the seat
belt all the way into the ceiling.
Place the latch plate and anchor
latch in their holding slots (see
page ).
Remove the covers on each lower
end of the seat-back by pulling on
the handles.
To install a LATCH-compatible child
seat in the second row center seat
(except LX models), use the center
lower anchors as shown above. Follow step 1 through 4 as
described previously to secure the
child seat.
1.
2.
3.
4.
5.
187
179
Installing a Child SeatUsing t he Cent er L A T CH48
LOWER ANCHORS
BUTTON TETHER STRAP
ATTACHING CLIP TETHER ANCHOR FITTING
HANDLE
COVER
10/07/17 09:40:43 31TK8600_053
2011 Odyssey

The location of each lower anchor is
indicated by a small button above the
anchor point.
To install a LATCH-compatible child
seat in a third row seat:
Unlatch the detachable seat belt
anchor latch and retract the seat
belt all the way into the ceiling.
Place the latch plate and anchor
latch in their holding slots (see
page ).
Push and pull the child seat
f orward and f rom side to side to
verify that it is secure.
Af ter properly securing the child
seat (see pages and ), lif t the
head restraint, then route the
tether strap over the seat-back and
through the head restraint legs.
1.
2.
6.
46 47
187
CONT INUED
Installing a Child Seat
Driver and Passenger Saf ety
49
LOWER ANCHORS BUTTON
10/07/17 09:40:50 31TK8600_054
2011 Odyssey

When not using the LATCH system,
all child seats must be secured to the
vehicle with the lap part of a lap/
shoulder belt.
In addition, the lap/shoulder belts in
all seating positions except the
driver’s have a lockable retractor
that must be activated to secure a
child seat.
If you intend to install a child seat in
the center seating position of the
second and third row, make sure the
detachable seat belt is securely
latched (see page ).
You can also remove the rear head
restraints (see page ). The
removedheadrestraintsshouldbe
secured in the cargo area so they
will not be thrown while you are
driving. Make sure to replace the
head restraints when the child
seats are not in use.
Followsteps6and7onpage .
With the child seat in the desired
seating position, route the belt
through the child seat according
to the seat maker’s instructions,
then insert the latch plate into the
buckle and remove any slack f rom
the lap portion of the belt.
1.
3.
4.
47
180
187
Installing a Child Seat
Installing a Child Seat with a L ap/
Shoulder Belt
50
10/07/17 09:40:57 31TK8600_055
2011 Odyssey

Push and pull the child seat
f orward and f rom side-to-side to
verify that it is secure enough to
stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract f ully, then repeat these
steps.
To deactivate the lockable retractor
and remove a child seat, unlatch the
buckle, unroute the seat belt, and let
the belt fully retract.
Af ter conf irming that the belt is
locked, grab the shoulder part of
the belt near the buckle, and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure.
To remove slack, it may help to
putweightonthechildseat,or
push on the back of the seat while
pulling up on the belt.
To activate the lockable retractor,
slowly pull the shoulder part of the
belt all the way out until it stops,
then let the belt f eed back into the
retractor.
Af ter the belt has retracted, tug on
it. If the belt is locked, you will not
be able to pull it out. If you can pull
thebeltout,itisnotlocked,and
you will need to repeat these steps.
5.
4.
2.
3.
Installing a Child Seat
Driver and Passenger Saf ety
51
10/07/17 09:41:05 31TK8600_056
2011 Odyssey

A child seat with a tether can be
installed in any seating position in
the second or third row seats.
Since a tether can provide additional
security to the lap/shoulder belt
installation, we recommend using a
tether whenever one is required or
available.Each second row seat has a tether
anchorage point behind the seat-
back. Attach the tether strap hook to the
anchor, making sure the strap is
not twisted. Af ter properly securing the child
seat (see pages and ), lif t the
head restraint, then route the
tether strap over the seat-back and
through the head restraint legs.
1.
2. 50 51
Installing a Child Seat with a
Tether
Second Row Inst allat ion
Installing a Child Seat52
TETHER ANCHOR POINTS
TETHER
STRAP HOOK
ANCHOR
Outer Position
10/07/17 09:41:12 31TK8600_057
2011 Odyssey

Each third row seat has a tether
anchorage point behind the seat-
back.Tighten the strap according to the
seat maker’s instructions. Attach the tether strap hook to the
anchor, making sure the tether
strap is not twisted.
You can also remove the rear head
restraints (see page ). The removedheadrestraintsshouldbe
secured in the cargo area so they will
not be thrown while you are driving.
Make sure to replace the head
restraints when the child seats are
not in use.
Af ter properly securing the child
seat (see pages and ), lif t the
head restraint, then route the
tether strap over the seat-back and
through the head restraint legs.
Tighten the strap according to the
seat maker’s instructions.
If the tether strap is too long and
cannot be tightened f irmly, f ind a
route where the strap can be
tightened securely. 3.
3.
1.
2.
5150
187T hird Row Inst allat ion
Installing a Child Seat
Driver and Passenger Saf ety
53
TETHER ANCHOR POINTS ANCHORTETHER STRAP HOOK
ANCHOR
Center Position (except LX models)
TETHER STRAP HOOK
10/07/17 09:41:21 31TK8600_058
2011 Odyssey