CAUTION
l
Since the fuel system may be under pres-
sure, remove the fuel tank filler tube cap
slowly. This relieves any pressure or vac-
uum that might have built up in the fuel
tank. If you hear a hissing sound, wait un-
til it stops before removing the cap. Oth-
erwise, fuel may spray out, injuring you
or others.
4. To
fill with fuel correctly depends mainly on correct handling of the fuel filler gun. Do not
tilt the gun. Insert the gun in the tank port as
far as it goes. CAUTION
l
A
label which reads “UNLEADED FUEL
ONLY” is attached to the fuel tank filler
lid of vehicles which can only operate us-
ing unleaded petrol. Serious engine and
catalytic converter damage will result if
leaded petrol is filled into these vehicles,
and consequently, this must never be at-
tempted.
5. When
the gun stops automatically, do not fill with fuel any more. CAUTION
l
To
avoid fuel spillage and overfilling, do
not “top-off” the fuel tank. 6. To
close, turn the fuel tank filler tube cap
slowly clockwise until you hear clicking
sounds, then gently push the fuel tank filler
door closed. CAUTION
l
If
you need to replace the fuel tank filler
tube cap, use only the cap specified for
your model vehicle. Installation of accessories
E00200300745
We
recommend you to consult your MITSUBISHI
MOTORS Authorized Service Point.
l The installation of accessories, optional
parts, etc., should only be carried out within
the limits prescribed by law in your country,
and in accordance with the guidelines fitting
instructions and warnings contained within
the documents accompanying the parts or ac-
cessories.
l Improper installation of electrical compo-
nents may cause an electrical fire if incorrect-
ly fitted. Please refer to the Modification/al-
teration to the electrical or fuel systems sec-
tion within this owner’s manual.
l Using a cellular phone or radio set inside the
vehicle without an external antenna may
cause electrical system interference, which
could lead to unsafe vehicle operation.
l Tyres and wheels which do not meet specifi-
cations must not be used.
Refer to the “Specifications” section for in-
formation regarding wheel and tyre sizes.
Important points!
Due to the large number of accessory and replace-
ment parts of different manufactures available in
the market, it is not possible, not only for
MITSUBISHI MOTORS, but also a MITSUBISHI
MOTORS Authorized Service Point, to check
whether the attachment or installation of such parts
affects thedriving safety of your MITSUBISHI-ve-
hicle.
General information
04
Presented by http://mmc-manuals.ru/ \251
Keyless entry system*
E00300302115
Press
the remote control switch, and all doors and
the tailgate will be locked or unlocked as desired. It
is also possible to operate the outside rear-view mir-
rors. 1- LOCK switch
2-
UNLOCK switch
3- Indication lamp
To lock
Press the LOCK switch (1). All the doors and the
tailgate will be locked. If the interior lamp switch
is in the middle position (DOOR) at this time, the
room lamp & map lamps, the rear personal lamps,
and the turn-signal lamps will blink once.
To unlock
Press the UNLOCK switch (2). All the doors and
the tailgate will be unlocked. If the interior lamp
switch is in the middle position (DOOR) at this
time, the room lamp & map lamps and the rear per-
sonal lamps will come on for approximately 15 sec-
onds and the turn-signal lamps will blink twice. NOTE
l The
indication lamp (3) comes on each time
a switch is pressed.
l If the UNLOCK switch (2) is pressed and no
door or tailgate is opened within approximate-
ly 30 seconds: relocking will automatically
occur.
l It is possible to modify functions as follows:
For further information, please contact your
MITSUBISHI MOTORS Authorized Service
Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details.
• The time from pressing the UNLOCKswitch (2) to the moment of automatic
locking can be changed.
• The confirmation function (flashing of the turn-signal lamps) can be set to oper-
ate only when the doors and backdoor are
locked or only when the doors and back-
door are unlocked.
• The confirmation function (this indicates locking or unlocking of the doors and tail-
gate with the flash of the turn-signal
lamps) can be deactivated.
• The number of times the turn-signal lamps are flashed by the confirmation
function can be changed.
Operation of the outside rear-view mir-
rors
To fold
Within 30 seconds of locking the doors and tailgate
using the LOCK switch (1), press the LOCK
switch twice rapidly to fold the outside rear-view
mirrors. To extend
Within
30 seconds of unlocking the doors and tail-
gate using the UNLOCK switch (2), press the UN-
LOCK switch twice rapidly to return the outside
rear-view mirrors to their extended positions.
NOTE
l The keyless entry system does not operate in
the following conditions:
• The key is left in the key cylinder.
• The door or tailgate is open.
l The remote control switch will operate with-
in about 4 m from the vehicle. However, the
operating range of the remote control switch
may change if the vehicle is located near a
power station, or radio/TV broadcasting sta-
tion.
l If either of the following problems occurs,
the battery may be exhausted.
• The remote control switch is operated atthe correct distance from the vehicle, but
the doors and tailgate are not locked/un-
locked in response.
• The indication lamp (3) is dim or does not come on.
For further information, please contact
your MITSUBISHI MOTORS Author-
ized Service Point.
If you replace the battery yourself, refer
to “Procedure for replacing the remote
control switch battery” on page 1-05.
l If your remote control switch is lost or dam-
aged, please contact your MITSUBISHI
MOTORS Authorized Service Point for a re-
placement remote control switch. Locking and unlocking
1-04
1
Presented by http://mmc-manuals.ru/ \251
Automatic mode (For vehicles with MITSUBISHI
MOTORS genuine audio)
The
automatic adjustment mode can set the local
time automatically by using the signal from local
RDS stations. In this mode, CT (A) is shown in the
display. Refer to “Radio data system (RDS)” on
page 5-18. Manual mode
The
manual mode is also available in case the auto-
matic mode shows the incorrect time when the ad-
jacent local RDS stations are located in a different
time zone. Refer to “Radio data system (RDS)” on
page 5-18. Set the time by pressing the various buttons as
described below.
H- To adjust the hour
M- To adjust the minutes
SET- To reset the minutes to zero 10:30-11:29…Changes to 11:00
11:30-12:29…Changes to 12:00
Outside temperature E00503900019
This value shows the outside temperature of the ve-
hicle. If the outside air temperature drops below approx.
3 °C,
the alarm sounds and the outside air tempera-
ture figure flashes for about 10 seconds. CAUTION
l
There
is a danger the road might be icy,
even when the outside air temperature fig-
ure is not flashing, so please take care
when driving.
NOTE l The
outside temperature can be displayed
from -40 °C to 50 °C.
l The outside temperature displayed may dif-
fer from the actual temperature on account of
surrounding conditions, driving conditions,
etc.
l When the outside temperature is below
-40 °C or over 50 °C, the display will remain
-40 °C or 50 °C. Instruments and controls
3-12
3
Presented by http://mmc-manuals.ru/ \251
The mirrors can be extended and retracted for 30
seconds
after the ignition switch is turned to the
“LOCK” position.
Either the mirror switch in the cabin or the remote
controller of the keyless entry system (if so equip-
ped) can be used.
For information on the keyless entry system, refer
to page 1-04.
NOTE
l It is also possible to fold and return the mir-
rors by hand.
l When freezing has occurred and mirrors fail
to operate as intended, please refrain from re-
peated pushing of the retractor switch as this
action can result in burn-out of the mirror mo-
tor circuits.
Automatic extension of mirrors
If the engine is stopped and started with the mirrors
retracted, the mirrors automatically extend for safe-
ty when the vehicle speed reaches 30 km/h
(19 mph).
NOTE l If the mirrors are retracted manually or using
the mirror switch after the engine is started,
they do not extend automatically. Use the mir-
ror switch to extend the mirrors, or turn the
ignition switch to the “LOCK” position to ac-
tivate the automatic extension function. Heated mirror*
E00601200442
When
the rear window demister switch is pressed,
the outside rear-view mirrors are demisted or de-
frosted. Current will flow through the heater ele-
ment inside the mirrors, thus clearing away frost or
condensation.
The indication lamp (C) will illuminate while the
demister is on. The heater will be turned off auto-
matically in about 20 minutes. Ignition switch
E00601401731 LOCK
The
engine is stopped and the steering wheel
locked. The key can be inserted and removed only
when the switch is in this position.
ACC
The engine is stopped, but the electrical devices
such as the radio and cigarette lighter can be operat-
ed.
ON
The engine is running, and all the vehicle’s electri-
cal devices can be operated.
START
The starter motor operates. After the engine has star-
ted, release the key and it will automatically return
to the “ON” position. Starting and driving
4-08
4 M/T
A/T
Presented by http://mmc-manuals.ru/ \251
The detection areas are within approximately
50
cm (A) from the corner sensors, 100 cm (B)
from the back sensors, and 60 cm (C) or less from
the ground surface, excluding the area approximate-
ly 10 cm (D) from the ground surface. The non-de-
tection areas (E) are within approximately 20 cm
(F) from the bumper. NOTE
l If
the rear bumper has been exposed to an im-
pact, the corner or back sensors may fail and
prevent the system from functioning proper-
ly. We recommend you to have your vehicle
inspected.
l The sensors do not detect objects located in
the area directly below or near the bumper. If
the height of an object is lower than the moun-
ted position of the corner or back sensors,
the sensors may not continue detecting it
even if they detected it initially.
For information on how to change the detection
areas, please refer to “Changing the detection
areas” on page 4-31. CAUTION
l
The
corner sensor system may not oper-
ate properly under the following condi-
tions: • The sensors or surroundings are cov-ered with ice, snow, or mud.
• The sensors are frozen.
• The system receives ultrasonic noise from other sources (the horns of other
vehicles, motorcycle engines, brakes,
radios, pouring rain, splashing water,
tyre chains, etc.).
• The sensors are extremely hot or cold (while the vehicle is parked for a long
period of time under a blazing sun or
in cold weather).
• The vehicle tilts significantly.
• The vehicle is driven on a rough road (with a bumpy, gravel, hilly, or grassy
surface).
• The vehicle is too close to an obstacle.
• The sensors or surroundings have been wiped by hand, or stickers or ac-
cessories have been attached.
l The corner sensor system may not prop-
erly detect the following:
• Objects that are thin, such as wirenets or ropes.
• Objects that absorb sound waves, such as snow.
• Objects that are shaped with a sharp angle.
• Objects with a smooth surface, such as glass.
• Objects that are low, such as kerb- stones. NOTE
l The
buzzer may sound lower than the normal
warning sound when the corner sensor sys-
tem is receiving ultrasonic noise from other
sources, but this is not a malfunction. The buz-
zer will stop sounding and the system will re-
turn to normal operation after the noise is no
longer received.
To operate E00615700448
To operate the system while the ignition switch is
“ON”,
move the selector lever to the “R” (RE-
VERSE) position on an A/T vehicle, or move the
gearshift lever to the “R” (Reverse) position on a
M/T vehicle. To stop the operation, push the “SO-
NAR” switch. The “SONAR OFF” indication lamp will illumi-
nate
to indicate that the system has stopped operat-
ing. Starting and driving
4-30
4
Presented by http://mmc-manuals.ru/ \251
Ventilators
.................................................................................... 5-02
Front automatic air conditioning ..................................................5-05
Rear heater*/Rear cooler* ............................................................ 5-09
Rear automatic air conditioning* .................................................5-09
Important operation tips for the air conditioning..........................5-11
Air purifier (with deodorizing function)* .....................................5-12
LW/MW/FM electronic tuning radio with CD player* ................5-13
Error codes.................................................................................... 5-28
Handling of compact discs ........................................................... 5-30
Antenna......................................................................................... 5-31
Sun visors..................................................................................... 5-32
Vanity mirror ................................................................................ 5-32
Ashtray.......................................................................................... 5-33
Cigarette lighter* .......................................................................... 5-34
Accessory socket*........................................................................ 5-35
Interior lamps ................................................................................ 5-35
Storage spaces............................................................................... 5-38
Cup holder.................................................................................... 5-40
Bottle holder ................................................................................. 5-41
Card holder (RHD vehicles only) .................................................5-42
Personal table* .............................................................................. 5-42
Tonneau cover* ............................................................................ 5-42
Assist grip..................................................................................... 5-44
Coat hooks*.................................................................................. 5-44
Luggage hooks.............................................................................. 5-45
Cargo net*..................................................................................... 5-45
Warning triangle retaining bands .................................................5-45For pleasant driving
5●
For details on a vehicle equipped with a Multi Dis-
play Station (MDS), refer to a separate operation
manual.
Presented by http://mmc-manuals.ru/ \251
LW/MW/FM electronic tuning radio with CD player*
E00708501891
The audio system can be used when the ignition switch is in the “ON” or “ACC” position. A- Display window
B- Audio system
NOTE l The MITSUBISHI genuine CD autochanger can be connected to this audio system.
The CD autochanger can be operated by the switch of the audio body. Refer to
“To listen to a CD” on page 5-24.
l To listen to the audio system while the engine is stopped, turn the ignition key to the “ACC” position.
l If a cellular phone is used inside the vehicle, it may create noise from the audio equipment. This does not mean that anything is wrong with your audio
equipment. In such a case, use the cellular phone at a place as far away as possible from the audio equipment.
l If foreign objects or water get into the audio equipment, or if smoke or a strange odour comes from it, immediately turn off the audio system and have it
checked. Never try to repair it by yourself. Avoid continuous usage without inspection by a qualified person. For pleasant driving
5-13 5
Presented by http://mmc-manuals.ru/ \251
Radio control panel and display
E007089007131. AM/FM (FM/MW/LW selection) button
2.
TUNE/SEEK (Down-step/Down-seek) button
3. TUNE/SEEK (Up-step/Up-seek) button
4. Memory select buttons
5. PWR (On-Off) switch 6. FM (FM1/FM2/FM3) indicators
7.
ST (Stereo) indicator
8. Preset memory number display
9. Frequency display window For pleasant driving
5-16
5
Presented by http://mmc-manuals.ru/ \251