2010 MITSUBISHI GRANDIS spare wheel

Luggage area
E00100400833 1. Luggage floor box p. 5-39
2.
Warning triangle retaining bands p. 5-45
3. Spare wheel p. 6-08
4. Tools and jack p. 6-06
5. Luggage hooks p. 5-45
6. Rear side box p. 5-39 Overview1
2
3
4 5
6
Presented by http://mmc-manuals.ru/ \251

Power steering system
E00607400127
When
the engine is stopped, the power steering sys-
tem will not function and it will require greater man-
ual effort to operate the steering wheel. Keep this
in mind in particular when towing the vehicle. Nev-
er turn off the engine while driving.
Periodically check the power steering fluid level. CAUTION
l
Do
not hold the steering wheel in the fully
turned position (either left or right), for
longer than 10 seconds.
This can cause damage to the power steer-
ing system. Active stability control (ASC)*
E00611700147
The

Active Stability Control (ASC) takes overall
control of the anti-lock brake system, traction con-
trol function and stability control function to help
maintain the vehicle’s control and traction. Please
read this section in conjunction with the page on
the anti-lock brake system, traction control func-
tion and stability control function.

Anti-lock brake system (ABS) ® p. 4-21
Traction control function ® p. 4-23
Stability control function ® p. 4-24 CAUTION
l
Do
not over-rely on the ASC. Even when
the ASC is operating, there are limits to
the system and its ability to maintain con-
trol and traction. Reckless driving may
lead to accidents. Always drive carefully,
taking account of the road conditions.
l Be sure to use the same specified type and
size of tyre on all 4 wheels. Otherwise,
there is a possibility that the ASC will not
work properly.
NOTE l In

the following situation, a click is heard
from the engine compartment; however, this
is only the sound of ASC being checked. • After turning the ignition switch to the“ON” position.
• After your vehicle is driven a short dis- tance after starting the engine. l
Some
vibration will be felt in the vehicle
body and a whining sound of a motor will be
heard from the engine compartment when
the ASC functions. This is a normal result of
the ASC operation, and does not indicate a
malfunction.
l The ASC does not operate while the ABS
warning lamp is illuminated.
Traction control function E00611800050
On slippery surfaces, traction control function pre-
vents

the drive wheels from excessive spinning,
thus helping the vehicle to start moving from a stop-
ped condition. It also provides sufficient driving
force and steering performance as the vehicle turns
at accelerated speeds. CAUTION
l
When
driving a vehicle on a snowy or icy
road, be sure to install snow tyres and
drive the vehicle at moderate speeds.
l When a tyre such as a compact spare
tyre, which is different in size from the
standard tyre, has been installed, make
sure that the traction control function is
turned off.
NOTE l When

moving out of mud, sand or fresh
snow, pressing the accelerator pedal may not
allow the engine speed to increase.
If this happens and the vehicle remains stuck
as a result, turn the TCL switch OFF. The ve-
hicle will then be easier to extricate. Starting and driving
4-23 4
Presented by http://mmc-manuals.ru/ \251

If the vehicle breaks down
............................................................ 6-02
Emergency starting ....................................................................... 6-02
Engine overheating ....................................................................... 6-04
Tools and jack ............................................................................... 6-06
Jacking up the vehicle
................................................................... 6-07
Spare wheel...................................................................................6-08
How to change a tyre .................................................................... 6-11
Towing.......................................................................................... 6-14
Operation under adverse driving conditions .................................6-18For emergencies
6
Presented by http://mmc-manuals.ru/ \251

WARNING
l Set the jack only at the positions shown
here. If the jack is set at a wrong position,
it could dent your vehicle or the jack
might fall over and cause personal injury.
l Do not use the jack on a tilted or soft sur-
face.
Otherwise, the jack might slip and cause
personal injury. Always use the jack on a
flat, hard surface. Before setting the jack,
make sure there are no sand or pebbles
under the jack base.
7. Rotate
the jack by hand until the flange por- tion (D) fits in the groove (E) at the top of
the jack. 8. Remove
the wheel nut wrench and bar from
under the third seat. (Refer to “Tools and
jack” on page 6-06.)
9. Insert the bar (F) into the wheel nut wrench (G). Then put the end of the bar into the
shaft’s jack end, as shown in the illustration. Slowly rotate the wheel nut wrench until the
tyre is raised slightly off the ground surface.
WARNING
l Stop
jacking up the vehicle as soon as the
tyre is raised off the ground. It is danger-
ous to raise the vehicle any higher.
l Do not get under your vehicle while using
the jack.
l Do not bump the raised vehicle or leave it
sitting on the jack for a long time. Both
are very dangerous.
l Do not use a jack except the one that
came with your vehicle.
l The jack should not be used for any pur-
pose other than to change a tyre.
l No one should be in your vehicle when us-
ing the jack.
l Do not start or run the engine while your
vehicle is on the jack.
l Do not turn the raised wheel. The tyres
still on the ground could turn and make
your vehicle fall off the jack. Spare wheel
E00801101440
Check

the air pressure of the spare tyre frequently
and make sure it is ready for emergency use at any
time.

Maintaining the spare wheel at the highest speci-
fied air pressure will ensure that it can always be
used under any conditions (city/high-speed driving,
varying load weight, etc.).
The spare wheel is stored under the rear of the body.
Compact spare wheel
The compact spare tyre is designed to save space in
the luggage compartment and its lighter weight
makes it easier to use if a flat tyre occurs. CAUTION
l
The
pressure should be periodically
checked and maintained at the specified
pressure while the tyre is stowed.
Driving with an insufficient tyre pressure
can lead to an accident. If you have no
choice but to drive with an insufficient
tyre pressure, keep your speed down and
inflate the tyre to the correct pressure as
soon as possible. (Refer to “Tyre inflation
pressures” on page 8-12.)
l The compact spare wheel is for tempora-
ry use only and should be removed as
soon as the original wheel can be re-
paired or replaced.
l The vehicle must not be driven at speeds
in excess of 80 km/h (50 mph) while using
the compact spare wheel. For emergencies
6-08
6
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
The compact spare tyre is not as good as
a standard tyre in controllability and sta-
bility. When the compact spare tyre is
used, avoid quick starts, sudden braking
and sharp steering.
l Avoid driving through automatic vehicle
washers and over obstacles that could pos-
sibly damage the vehicle’s undercarriage.
Because the compact spare wheel is small-
er than the original wheel, the ground
clearance is slightly reduced.
l The compact spare wheel is specifically de-
signed for your vehicle and it should not
be used on any other vehicle. CAUTION
l
Do
not use tyre chain with your compact
spare wheel. Because of the smaller tyre
size, a tyre chain will not fit properly.
This could cause damage to the wheel
and result in loss of the chain.
If a front tyre becomes flat when using
tyre chains, first replace a rear wheel
with the compact spare wheel and then
use the removed rear wheel to replace the
flat front wheel so that you can continue
to use the chains. CAUTION
l
The
compact spare tyre should not be
used on any other wheels, nor should
standard tyres, snow tyres, wheel covers
or trim rings be used with the compact
spare wheel. If such use is attempted, dam-
age to these items or other vehicle compo-
nents may occur.
l Upon installation of the compact spare
tyre, the overall vehicle height is lowered
slightly as the tyre is smaller in diameter
than the standard tyre. When passing
over the projections on the road, take
care not to drive the vehicle with the
same feeling as used in driving with the
standard tyre on.
l Do not install more than one compact
spare wheel at the same time.
l When the tread wear indicators appear,
the tyre must be replaced.
Refer to “Wheel condition” on page 8-13. NOTE
l The

wheel hanger is designed for a compact
spare wheel only. It cannot be used for stor-
age of any other kind of wheel.
Store any wheel with a punctured tyre in the
luggage area.
l Check that the compact spare wheel is not
loose by trying to joggle it with your hands
or feet. If it is loose, the wheel hanger or
hook may be deformed. Store the wheel in-
side the luggage area, and have it repaired.
To remove 1. Open the tailgate and remove the lid of thehanger mounting bolt with the bar. 2. Loosen
the hanger mounting bolt with the
wheel nut wrench. For emergencies
6-09 6
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
If you loosen the hanger mounting bolt
too much, the holder will come free and
the spare wheel will fall down. Pay close
attention to the bolt while loosening it.
3. Unlock
the hanger (A) from the holder (B) by lifting the part that is shown by the arrow
in the drawing. Lower it to remove the spare
wheel. CAUTION
l
When
removing the hanger from the hold-
er or hooking the hanger onto the holder,
hold the hanger securely to avoid drop-
ping it on your feet.
To install 1. Set
the spare wheel onto the centre of the
hanger (A).
2. Raise the hanger and hook it onto the holder (B). CAUTION
l
Do
not hang the holder in any position oth-
er than the hanger’s correct position. The
holder could scratch the vehicle body,
and the spare wheel could fall down, re-
sulting in an accident. 3. Tighten
the holder mounting bolt securely
with the wheel nut wrench. 4. Fit the cover over the hanger mounting bolt.
5. After

tightening the bolt, try joggling the
spare wheel to confirm that there is no play
in the hanger. For emergencies
6-10
6
Presented by http://mmc-manuals.ru/ \251

How to change a tyre
E00801202523
Before
changing a tyre, first stop your vehicle in a
safe, flat location. 1. Park the vehicle on level and stable ground.
2. Set the parking brake firmly.
3. On vehicles with M/T, turn the ignition keyto the “LOCK” position, move the gearshift
lever to the “R” (Reverse) position.
On vehicles with A/T, move the selector lev-
er to the “P” (PARK) position, turn the igni-
tion key to the “LOCK” position.
4. Turn on the hazard warning flashers and set up a warning triangle, flashing signal lamp,
etc., at an adequate distance from the vehi-
cle, and have all your passengers leave the ve-
hicle.
5. To prevent the vehicle from rolling when it is raised on the jack, place chocks or blocks
(A) at the tyre that is diagonally opposite
from the tyre (B) you are changing. WARNING
l Be
sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.
If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.
NOTE l The

chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if nee-
ded.
l If chocks are not available, use stones or any
other objects that are large enough to hold
the wheel in position.
6. Get the spare wheel, jack, jack handle and wheel nut wrench ready. NOTE
l Put

the spare wheel under the vehicle body
near the jack. This makes it safer if the jack
slips out of position. 7. On
vehicles with wheel covers, first remove
the covers (refer to “Wheel covers” on page
6-13). Then loosen the wheel nuts with the
wheel nut wrench. Do not remove the wheel
nuts yet. 8. Find
the closest jacking point to the flat tyre
(refer to the “Jacking up the vehicle” on page
6-07). Then position the jack and raise the ve-
hicle until the tyre is slightly off the ground.
9. Remove the wheel nuts with the wheel nut wrench, then take the wheel off. CAUTION
l
Handle
the wheel carefully when chang-
ing the tyre, to avoid scratching the wheel
surface.
10. Clean
out any mud, etc. on the hub surface (C), hub bolts (D) or in the installation holes
(E) in the wheel, and then mount the spare tyre. For emergencies
6-11 6
Presented by http://mmc-manuals.ru/ \251

WARNING
l Mount the spare wheel with the valve
stem (F) facing outboard. If you cannot
see the valve stem (F), you have installed
the wheel backwards.
Operating the vehicle with the spare
wheel installed backwards can cause vehi-
cle damage and result in an accident. 11. Finger-tighten

the wheel nuts. (Turn them
clockwise.)
Vehicle with steel wheels
Tighten
the wheel nuts until the tapered
parts of the wheel nuts make light contact
with the seats of the wheel holes and the
wheel is not loose.
Tighten the wheel nuts in the same way
with a compact spare wheel.
Vehicle with aluminium wheels
With

a normal wheel, tighten the wheel
nuts until the flanges of the wheel nuts
touch the wheel and the wheel is not loose.
Normal wheel With a compact spare wheel, tighten the
wheel

nuts until the tapered parts of the wheel nuts make light contact with the
seats

of the wheel holes and the wheel is
not loose.
Compact spare wheel CAUTION
l
Never
apply oil to either the wheel bolts
or the nuts, or they will tighten too much.
NOTE l Flange

nuts can be temporarily used on the
spare wheel, but return to the original wheel
and tyre as soon as possible.
l If all four aluminium wheels are changed to
steel wheels, use tapered nuts.
12. Lower the vehicle slowly and then tighten the nuts in the order shown in the illustration
until each nut has been tightened to the tor-
que listed here.
Tightening torque
88 to 108 N•m For emergencies
6-12
6
Presented by http://mmc-manuals.ru/ \251