2010 MITSUBISHI GRANDIS clock

Filling the fuel tank
E00200202142WARNING
l Petrol is highly flammable and explosive.
You could be burned or seriously injured
when handling it. When refueling your ve-
hicle, always turn the engine off and keep
away from flames, sparks, and smoking
materials. Always handle fuel in well-ven-
tilated outdoor areas.
l Before removing the fuel cap, be sure to
get rid of your body’s static electricity by
touching a metal part of the car or the
fuel pump. Any static electricity on your
body could create a spark that ignites
fuel vapour.
l Perform the whole refueling process
(opening the fuel tank filler door, remov-
ing the fuel cap, etc.) by yourself. Do not
let any other person come near the fuel
tank filler. If you allowed a person to
help you and that person was carrying
static electricity, fuel vapour could be ig-
nited.
l Do not move away from the fuel tank fill-
er until refueling is finished. If you
moved away and did something else (for
example, cleaning your windscreen) part-
way through the refueling process, you
could pick up a fresh charge of static elec-
tricity.
l Be careful not to inhale fuel vapour. Fuel
contains toxic substances. WARNING
l Keep
the doors and windows closed while
refueling the vehicle. If they were open,
fuel vapour could get into the cabin.
Fuel tank capacity
65 litres
Refueling 1.

Before filling with fuel, stop the engine.
2. The fuel tank filler is located on the rear left side of your vehicle.
The fuel tank filler door can be opened from
inside the vehicle with the fuel tank filler
door release lever located below the instru-
ment panel. 3. Open
the fuel tank filler tube by slowly turn-
ing the cap anticlockwise. A- Remove
B- Close General information
03 LHD RHD
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
Since the fuel system may be under pres-
sure, remove the fuel tank filler tube cap
slowly. This relieves any pressure or vac-
uum that might have built up in the fuel
tank. If you hear a hissing sound, wait un-
til it stops before removing the cap. Oth-
erwise, fuel may spray out, injuring you
or others.
4. To
fill with fuel correctly depends mainly on correct handling of the fuel filler gun. Do not
tilt the gun. Insert the gun in the tank port as
far as it goes. CAUTION
l
A
label which reads “UNLEADED FUEL
ONLY” is attached to the fuel tank filler
lid of vehicles which can only operate us-
ing unleaded petrol. Serious engine and
catalytic converter damage will result if
leaded petrol is filled into these vehicles,
and consequently, this must never be at-
tempted.
5. When
the gun stops automatically, do not fill with fuel any more. CAUTION
l
To
avoid fuel spillage and overfilling, do
not “top-off” the fuel tank. 6. To
close, turn the fuel tank filler tube cap
slowly clockwise until you hear clicking
sounds, then gently push the fuel tank filler
door closed. CAUTION
l
If
you need to replace the fuel tank filler
tube cap, use only the cap specified for
your model vehicle. Installation of accessories
E00200300745
We

recommend you to consult your MITSUBISHI
MOTORS Authorized Service Point.
l The installation of accessories, optional
parts, etc., should only be carried out within
the limits prescribed by law in your country,
and in accordance with the guidelines fitting
instructions and warnings contained within
the documents accompanying the parts or ac-
cessories.
l Improper installation of electrical compo-
nents may cause an electrical fire if incorrect-
ly fitted. Please refer to the Modification/al-
teration to the electrical or fuel systems sec-
tion within this owner’s manual.
l Using a cellular phone or radio set inside the
vehicle without an external antenna may
cause electrical system interference, which
could lead to unsafe vehicle operation.
l Tyres and wheels which do not meet specifi-
cations must not be used.
Refer to the “Specifications” section for in-
formation regarding wheel and tyre sizes.
Important points!
Due to the large number of accessory and replace-
ment parts of different manufactures available in
the market, it is not possible, not only for
MITSUBISHI MOTORS, but also a MITSUBISHI
MOTORS Authorized Service Point, to check
whether the attachment or installation of such parts
affects thedriving safety of your MITSUBISHI-ve-
hicle.
General information
04
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
If you continue driving with
low engine oil level or with this
warning lamp illuminated, en-
gine seizure may occur.
NOTE l The

oil pressure warning lamp
should not be treated as an indica-
tion of the engine’s oil level. The
oil level must be checked using
the dipstick. Door ajar warning lamp
E00503300765
This

lamp illuminates when a door or
the tailgate is either open or incomplete-
ly closed.
If the vehicle speed reaches approximate-
ly 8 km/h (5 mph) with a door or the tail-
gate open or incompletely closed, the
warning lamp flashes 8 times and a buz-
zer simultaneously sounds 8 times as a
warning. CAUTION
l
Before
moving your vehicle,
check that the warning lamp is
OFF. NOTE
l On

vehicles with keyless entry sys-
tem, the lamp remains illuminated
for a certain period and then goes
out automatically. Refer to
“Lamps (room lamps, etc.) auto-
cutout function” on page 5-37.
l It is possible to change the buzzer
setting for either of the following
types of operation. For further in-
formation, we recommend you to
consult a MITSUBISHI
MOTORS Authorized Service
Point.
• No buzzer operation (buzzerdisabled)
• Continuous buzzer operation Multi centre display
E00503600120 WARNING
l When
operating the system for a pro-
longed period, make sure the vehicle is
parked in a well ventilated area to avoid
the accumulation of toxic fumes inside
and outside of the passenger compartment. CAUTION
l
The
driver should not operate the display
while the vehicle is in motion.
l When operating the system, stop the vehi-
cle in a safe area.
When the ignition switch is in the “ACC” position,
the
digital clock is displayed in the multi centre dis-
play. When the ignition switch is in the “ON” posi-
tion, the momentary fuel consumption and outside
temperature are displayed besides digital clock. Instruments and controls
3-09 3
Presented by http://mmc-manuals.ru/ \251

A-
Outside temperature ® p. 3-12
B- Driving information ® p. 3-13
C- Digital clock ® p. 3-10
NOTE l The display unit (ex. km or mile) and bright-
ness can be changed as desired. (Refer to
“Display brightness adjustment” on page
3-16 and “Display unit selection” on page
3-16.) When the system cannot provide a def-
inite value for momentary fuel consumption/
average fuel consumption/driving range/aver-
age speed, it is displayed as “---”.
l The figure of the display varies according to
the conditions under which a vehicle is trav-
elling (road conditions, the manner in which
the vehicle is being driven, etc.).
Observe display for reference because the fig-
ure of the display may differ from the actual
figure. Digital clock
E00503700118 Following modes are available for digital clock ad-
justment:
l For

vehicles with MITSUBISHI MOTORS
genuine audio automatic mode and manual
mode l
Except
for vehicles with MITSUBISHI
MOTORS genuine audio manual mode only

Select the automatic mode or the manual mode by
performing the following operations: 1. Enter the function setup mode by pushingthe “MENU” button. Instruments and controls
3-10
3
Presented by http://mmc-manuals.ru/ \251

2. Press the “MENU” button repeatedly to se-
lect the CT (Clock Time) mode.
The order is: AF → CT → REG → TP-S →
PH → MUTE (With PH OFF, this mode is
not displayed.) → Language of PTY display
→ Function setup mode OFF
(Refer to “Function setup mode” on page
5-21.)
NOTE l Although “PH” and “MUTE” appear on the
display, the PH and MUTE functions are in-
operative.
3. Make your selection by pressing the “ ”
button or the “ ” button. - CT ON (Automatic mode)
- CT OFF (Manual mode)NOTE
l After
selecting a mode, you can leave the func-
tion setup mode by taking either of the fol-
lowing steps: • Press the “MENU” button for at least 2seconds.
• Make no entry for 7 seconds. Instruments and controls
3-11 3
Presented by http://mmc-manuals.ru/ \251

l
To cancel the unit setting procedure before
completion, press the button (A). l
The
outside temperature and digital clock are
not shown during the unit selecting procedure.
l If the “SET” button is not pressed for about
15 seconds or longer in the middle of the se-
lection, the currently selected unit is set auto-
matically. The display will return to the orig-
inal display item. Combination headlamps and
dipper switch E00506000776
Headlamps
Rotate the switch to turn on the lamps. OFF All lamps off
Position, tail, licence plate and instrument
panel lamps on
Headlamps and other lamps go on
NOTE
l Do

not leave the headlamps and other lamps
on for a long while the engine is stationary.
A run-down battery could result. l
When
it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon
as when window glass mists up on a humid
day, and does not indicate a functional prob-
lem. When the lamp is switched on, the heat
will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to
have it checked.
[Vehicles with Daytime Running Lamp]
When the ignition switch is in the “ON” position
and the lamp switch is set to the “OFF” position,
the low beam of the headlamps, tail lamps, etc.,
will illuminate.
Lamps (headlamps, fog lamp, etc.) au-
to-cutout function l If the key is turned to the “LOCK” or
“ACC” position or removed from the igni-
tion switch and the lamps will stay on for
about 3 minutes without opening the driver’s
door while the lamp switch in the “ ” posi-
tion, automatically turn off.
l If

the key is turned to the “LOCK” or
“ACC” position or removed from the igni-
tion switch and the driver’s door is opened
within 3 minutes while the lamp switch in
the “ ”
position, a buzzer will sound to
warn the driver that the lamps have not been
turned off, and these lamps will automatical-
ly turn off.
NOTE l The lamp auto-cutout will not function when
the lamp switch is in the “ ” position.Instruments and controls
3-18
3
Presented by http://mmc-manuals.ru/ \251

Front automatic air conditioning
E00702400048
The
air conditioning can only be used while the en-
gine is running.
Control panel E00702501293A- Mode selection dial
B-
Blower speed selection dial
C- Air conditioning switch
D- Temperature control dial E- Air selection switch NOTE
l There

is an interior air temperature sensor
(F) inside the vehicle.
Never place anything on top of the sensor,
since doing so will prevent it from function-
ing properly. Blower speed selection dial
E00702800127
Select the blower speed by turning the blower
speed selection dial clockwise or anticlockwise.
The

blower speed will gradually increase as the di-
al is turned to the right. When the blower speed selection dial is set to the
“OFF” position, all fan-driven airflow will stop. Temperature control dial
E00703000520
Turn the temperature control dial clockwise to
make

the air warmer. Turn it anticlockwise to
make the air cooler. For pleasant driving
5-05 5
Presented by http://mmc-manuals.ru/ \251

To adjust the volume
E00708700069
VOL (Volume control)
Turn
the VOL knob (2) clockwise to increase the
volume; anticlockwise to decrease the volume. The
status will be displayed in the display (6).
To adjust the tone E00708800640
Press the AUDIO button (3) to select BASS TRE FADE BAL Audio adjust mode off.
The status will be displayed in the display (6).
BASS (Bass tone control)
Press

the audio adjust button (5) either or
to select the desired bass tone quality.
TRE (Treble tone control)
Press

the audio adjust button (5) either or
to select the desired treble tone quality.
FADE (Front/Rear balance control)
Press

the audio adjust button (5) either or
to balance the volume of sound from the front and
the rear speakers.
BAL (Left/Right balance control)
Press

the audio adjust button (5) either or
to balance the volume of sound from the left and
the right speakers. NOTE
l Audio

adjust mode will be cancelled when ra-
dio or CD operation is performed or no ad-
justment is performed for more than 7 seconds. To enter audio tone settings into the memory
It
is possible to enter the audio adjustment condi-
tion (BASS, TRE, FADE, BAL) into the memory. 1. Make the desired adjustments in the audio ad-just mode. Refer to “To adjust the tone” on
page 5-15.
2. In the audio adjust mode, press and hold one of the memory select buttons (4) [1-6]. When
you hear a bleep, the memorization is com-
plete. The display will show the button num-
ber [SOUND1-SOUND6] for which the set-
tings were memorized.
3. In future, when you gently press the memory select button in the audio adjust mode, the au-
dio adjustment condition memorized for that
button will take effect. For pleasant driving
5-15 5
Presented by http://mmc-manuals.ru/ \251