2010 MITSUBISHI GRANDIS oil dipstick

CAUTION
l
If you continue driving with
low engine oil level or with this
warning lamp illuminated, en-
gine seizure may occur.
NOTE l The

oil pressure warning lamp
should not be treated as an indica-
tion of the engine’s oil level. The
oil level must be checked using
the dipstick. Door ajar warning lamp
E00503300765
This

lamp illuminates when a door or
the tailgate is either open or incomplete-
ly closed.
If the vehicle speed reaches approximate-
ly 8 km/h (5 mph) with a door or the tail-
gate open or incompletely closed, the
warning lamp flashes 8 times and a buz-
zer simultaneously sounds 8 times as a
warning. CAUTION
l
Before
moving your vehicle,
check that the warning lamp is
OFF. NOTE
l On

vehicles with keyless entry sys-
tem, the lamp remains illuminated
for a certain period and then goes
out automatically. Refer to
“Lamps (room lamps, etc.) auto-
cutout function” on page 5-37.
l It is possible to change the buzzer
setting for either of the following
types of operation. For further in-
formation, we recommend you to
consult a MITSUBISHI
MOTORS Authorized Service
Point.
• No buzzer operation (buzzerdisabled)
• Continuous buzzer operation Multi centre display
E00503600120 WARNING
l When
operating the system for a pro-
longed period, make sure the vehicle is
parked in a well ventilated area to avoid
the accumulation of toxic fumes inside
and outside of the passenger compartment. CAUTION
l
The
driver should not operate the display
while the vehicle is in motion.
l When operating the system, stop the vehi-
cle in a safe area.
When the ignition switch is in the “ACC” position,
the
digital clock is displayed in the multi centre dis-
play. When the ignition switch is in the “ON” posi-
tion, the momentary fuel consumption and outside
temperature are displayed besides digital clock. Instruments and controls
3-09 3
Presented by http://mmc-manuals.ru/ \251

3. Confirm that the cooling fans are turning. If
the fans are not turning, stop the engine im-
mediately and have it checked.
Petrol-powered vehicles
Diesel-powered vehicles A- Cooling fans
B- Radiator cap
C- Reserve tank lid
D- Reserve tank cap
*: Front of the vehicle
WARNING
l Be
careful not to get your hands or
clothes caught in the cooling fans. 4. After
the engine coolant temperature has drop-
ped to the normal temperature, stop the engine. 5. Check the coolant level in the reserve tank.
Petrol-powered vehicles
The

reserve tank lid (C) is equipped with a
dipstick.

Remove the dipstick and wipe it with a clean
cloth. Reinsert the dipstick as far as it goes.
Remove the dipstick and read the coolant lev-
el, which should always be within the range
indicated.
FULL
LOW WARNING
l If
there is none, make sure that the en-
gine has cooled down before removing
the radiator cap (B), because hot steam
or boiling water otherwise will gush from
the filler port and may scald you.
Diesel-powered vehicles
The
coolant level in this tank should be kept
between the “LOW” and “FULL” marks.
FULL
LOW WARNING
l If
there is none, make sure that the en-
gine has cooled down before removing
the reserve tank cap (D), because hot
steam or boiling water otherwise will
gush from the filler port and may scald
you.
6. Add
coolant to the radiator and/or reserve tank if necessary. (Refer to the “Mainte-
nance” section.) For emergencies
6-05 6
Presented by http://mmc-manuals.ru/ \251

Diesel-powered vehicles (for
diesel particulate filter models)
The engine oil used has a significant effect on the
engine’s performance, service life and startability.
Be sure to use oil of the recommended quality and
appropriate viscosity.
All engines consume a certain amount of oil during
normal operation, and engine oil consumption is
greatly influenced by payload, engine speed, etc.
Therefore, it is important to check the oil level at
regular intervals or before starting a long trip.
This check must be made with the engine warm but
not running. Park the vehicle on a level surface,
stop the engine, and then wait a few moments to al-
low the engine oil in circulation to return to the oil
pan to ensure accurate measurement.
Remove the dipstick and wipe it with a clean cloth.
Reinsert the dipstick as far as it goes. Remove the
dipstick and read the oil level, which should al-
ways be within the range indicated.
If the oil level is below the specified limit, remove
the cap located on the cylinder head cover and add
enough oil to raise the level to within the specified
range.
Be sure to use the specified engine oil and do not
mix various types of oil. Also, avoid mixing differ-
ent makes of oil together if possible.
After adding oil, close the cap securely.
Use

only the recommended oils with an ACEA or
API classification as specified in this manual.
NOTE
l The engine oil will deteriorate rapidly if the
vehicle is subjected to severe conditions (for
example, repeated operation on rough roads,
in mountainous regions, on roads with many
uphill and downhill gradients, or over short
distances). Consequently, the oil will require
earlier replacement.
l For handling of used engine oils, refer to
page 06.
Selection of engine oil

Petrol-powered vehicles 1. Select
engine oil of the proper SAE viscosity
number according to the atmospheric temper-
ature.
SAE 0W-30, 5W-30, and 5W-40 engine oilscan only be used if they meet ACEA A3/B3,
A3/B4 or A5/B5 and API SG (or higher) spec-
ifications. 2. Use
engine oil conforming to the following
classification:
l API classification: “For service SG” or
higher
l ILSAC certificated oil
l ACEA classification:
“For service A1/B1, A3/B3, A3/B4 or
A5/B5”
NOTE l Use of additives is not recommended since
they may reduce the effectiveness of addi-
tives already included in the engine oil. It
may result in failure of the mechanical assem-
bly.

Diesel-powered vehicles Use engine oil conforming to the following
classification:• Vehicles with DPF= “VW 50700”
• Vehicles without DPF= “VW50501/50601/50700”
NOTE l Use of additives is not recommended since
they may reduce the effectiveness of addi-
tives already included in the engine oil. It
may result in failure of the mechanical assem-
bly. Maintenance
8-05 8
Presented by http://mmc-manuals.ru/ \251

Engine coolant
E01000501361
To check the coolant level
A
translucent coolant reserve tank is located in the
engine compartment.
Petrol-powered vehicles
Check the coolant level in the reserve tank. The re-
serve tank lid (B) is equipped with a dipstick.

Remove the dipstick and wipe it with a clean cloth.
Reinsert the dipstick as far as it goes. Remove the
dipstick and read the coolant level, which should al-
ways be within the range “F” (FULL) or “L”
(LOW) while the engine is cold.
FULL
LOW To add coolant
The

cooling system is a closed system and normal-
ly the loss of coolant should be very slight. A no-
ticeable drop in the coolant level could indicate leak-
age. If this occurs, we recommend you to have the
system checked as soon as possible.
If the level should drop below the “L” (LOW) level
on the dipstick, add coolant to the reserve tank. Also, if the reserve tank is completely empty, re-
move

the radiator cap (A) and add coolant until the
level reaches the filler neck. WARNING
l Do
not open the radiator cap while the en-
gine is hot. The coolant system is under
pressure and any hot coolant escaping
could cause severe burns.
Anti-freeze
The
engine coolant contains an ethylene glycol anti-
corrosion agent. The cylinder head and water pump
housing are cast aluminium alloy, and periodic
changing of the engine coolant is necessary to pre-
vent corrosion of these parts.

Use “DIA QUEEN SUPER LONG LIFE COOL-
ANT” or equivalent.
MITSUBISHI Genuine Coolant has excellent pro-
tection against corrosion and rust formation of all
metals including aluminium and can avoid block-
ages in the radiator, heater, cylinder head, engine
block, etc.
Because of the necessity of this anti-corrosion
agent, the coolant must not be replaced with plain
water even in summer. The required concentration
of anti-freeze differs depending on the expected am-
bient temperature. Ambient
temperature (minimum) °C -15 -20 -25 -30 -35 -50 Anti-freeze
concentra- tion % 30 35 40 45 50 60 CAUTION
l
Do
not use alcohol or methanol anti-
freeze or any engine coolants mixed with
alcohol or methanol anti-freeze. The use
of an improper anti-freeze can cause cor-
rosion of the aluminium components.
l For effective anti-corrosion and anti-
freeze performance, keep the anti-freeze
concentration within the range of 30 to
60 %.
Concentrations exceeding 60 % will re-
sult in a reduction of both the anti-freeze
and cooling performance thus adversely
affecting the engine.
l Do not top up with water only.
Water by itself reduces the rust-protec-
tive and anti-freeze qualities of the cool-
ant and has a lower boiling point. It can
also cause damage to the cooling system if
it should freeze. Do not use tapwater, as it
can cause corrosion and rust formation. Maintenance
8-06
8
Presented by http://mmc-manuals.ru/ \251

Automatic transmission fluid*
E01000600857
The
proper amount of automatic transmission fluid
is essential to the life and operation of the automat-
ic transmission. Either insufficient fluid or exces-
sive fluid could cause transmission trouble. The
transmission fluid filler port cap is equipped with a
dipstick. Use the following procedure to check the
fluid level.
Procedure for checking the fluid level
1. Check the fluid level after the vehicle hasbeen driven enough to warm up the transmis-
sion fluid.
2. Park the vehicle on a flat, level surface and apply the parking brake.
3. With the engine idling and the brake pedal fully depressed, move the transmission selec-
tor lever through all the positions from P”
(PARK) to “D” (DRIVE), stopping momen-
tarily at each position.
4. Move the selector lever to the “P” (PARK) position.
5. Remove the dipstick and wipe it with a clean lint-free cloth.
6. Reinsert the dipstick as far as it goes. 7. Remove dipstick and read the oil level.
The fluid level should always be between the
two marks on the dipstick. WARNING
l Do
not spill the fluid onto a hot exhaust
manifold during topping up or inspec-
tion, or a fire may occur.
Fluid type
Use
only “DIA QUEEN ATF SP III” transmission
fluid to ensure optimum transmission performance. Washer fluid
E01000700164
Check

the float (A) is between the “FULL” and
“EMPTY” marks on the washer fluid reservoir.
If the level is low, replenish the container with wash-
er fluid. NOTE
l The

washer fluid container serves the wind-
screen, rear window and headlamps*.
During cold weather
To ensure proper operation of the washers at low
temperatures, use a fluid containing an anti-freez-
ing agent. Maintenance
8-08
8
Presented by http://mmc-manuals.ru/ \251