2009 SKODA OCTAVIA TOUR Owner's Manual

Inspecting and replenishing
168
WARNING
•
Read and observe the warning notes
⇒page 160, “Working in the engine
compartment” before working in the engine compartment.•
If the fluid level has dropped below the “MIN” marking, do not drive any
further - risk of accident! Ob
tain professional assistance.
Replacing brake fluidBrake fluid absorbs moisture. This causes
the fluid to absorb moisture from the
surrounding air over a period of time. Excessive water in the brake fluid may be the cause of corrosion in the brake system. Th
e water content also lowers the boiling
point of the brake fluid.
This is why brake fluid must be replaced every two
years. One may only use new genuine brake fluid
from Škoda Auto. The specification for
the brake fluid is “FMVSS 116 DOT 4”. We recommend that you have th
e brake fluid replaced by a
specialist garage
as
part of an Inspection Service.
WARNING
•
Using old brake fluid can result in seve
re stress on the brakes because of
the formation of vapour bubbles in the brake system. This greatly impairs the braking efficiency and thus also the safety of your vehicle.•
Brake fluid is toxic! It must therefore be kept safely in closed original
containers and well aw
ay from children and unauthorized persons.
Caution
Brake fluid damages the pa
intwork of the vehicle.
For the sake of the environment
In view of the problems involved with prop
er disposal of brake fluid, the special
tools and the professional knowledge required, you should have the brake fluid replaced by a specialist garage.BatteryWorking on the batteryThe battery is located in the engine
compartment below a plastic cover*.
– Press the interlocks on the sides of the battery cover
⇒
fig. 156
and
pull the cover upwards see arrow .
– The installation of the battery cov
er takes place in the reverse order.
Removal and installation of the battery
is not recommended since it can, under
certain circumstances, lead to major
damage. Contact a specialist garage.
There is a risk of injuries, scalding, acci
dents and burns when carrying out any work
on the battery and on the electrical system. For this reason, it is essential to comply with the warning instructions
⇒
stated below and with the general applicable
rules of safety.
Fig. 156 Engine compart- ment: The battery
AA
s2g8.b.book Page 168 Tuesday, April 7, 2009 8:53 AM

Inspecting and replenishing
169
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
•
The battery acid is strongly corros
ive and must, therefore, be handled
with the greatest of care. Always we
ar protective gloves, eye and skin
protection when handling batteries. Corrosive fumes in the air irritate the air passages and lead to conjunctivitis
and inflammation of the air passages
in the lungs. Battery acid corrodes
dental enamel and creates deep wounds
after contact with the skin which take a long time to heal. Repeated contact with diluted acids causes skin diseases (inflammations, ulcers, slin cracks). Acids coming into contact with water are diluted accompanied by significant development of heat.•
Do not tilt the battery otherwise battery electrolyte may flow out of the
battery vent openings. Prot
ect the eyes with safety glasses or a shield! There
is the danger of suffering blindness! If
any battery electrol
yte gets into your
eye, rinse out your eye immediately
with clear water for several minutes.
Contact a doctor without delay.•
Splashes of acid on your skin or clothes should be neutralised as soon as
possible using soap suds and then rinsed with plenty of water. Contact a doctor immediately if you swallow battery electrolyte.•
Keep batteries out of the reach of children.
•
Hydrogen is released when you char
ge a battery and a highly explosive
gas mixture is produced. An explosion
can be caused through sparkling over
during unclamping or loosening of the cable plug while the ignition is on.•
Bridging of the poles will create a short circuit (e.g. through metal
objects, cables). Possible consequences of a short circuit: Melting of lead struts, explosion and burning of the battery, jets of acid spurting out.•
It is prohibited to work with a naked flame and light, to smoke or to carry
out any activities which produce sparks. Avoid creating sparks when working with cables and electrical device
s. Strong sparking represents a risk
of injury.•
Before carrying out any work on the electrical system, switch off the
engine, the ignition as well as all electrical components and disconnect the negative cable (-) on the battery. If you wish to replace a bulb it is sufficient to switch off the appropriate light.
•
Never charge a frozen or thawed battery - risk of explosion and caustic
burns! Replace a frozen battery.•
Never use a battery which is damaged
- risk of explosion! Immediately
replace a damaged battery.
Caution
•
You must only disconnect the battery if the ignition is switched off, otherwise
the electrical system (electronic components) of the vehicle may be damaged. When disconnecting the battery from the el
ectrical system of the vehicle, first
disconnect the negative terminal (-) of th
e battery. Then disconnect the positive
terminal (+).•
When reconnecting the battery, first conne
ct the positive terminal (+) and only
then the negative terminal (-) of the batt
ery. You must on no account connect the
cables wrongly - risk of a cable fire.•
Ensure that battery acid does not come
into contact with the vehicle body
otherwise damage could
occur to the paintwork.
•
Do not place the battery in direct dayl
ight in order to protect the battery
housing from the effects of ultra-violet light.
For the sake of the environment
A removed battery is a special type of waste which is harmful to the environment - contact your specialist garage regarding disposing of the battery.
Note
Please also refer to the guidelines
⇒page 171, “Disconnecting and reconnecting
the battery”, also after connecting the battery.
WARNING (continued)
s2g8.b.book Page 169 Tuesday, April 7, 2009 8:53 AM

Inspecting and replenishing
170
Battery with a charge level indicator, the so-called magic eye*There is a so-called magic eye
⇒fig. 157
located on the top of the battery. The
“magic eye” changes its colour in line with the charge state and the electrolyte level of the battery. Air bubbles can influence the colour of th
e “magic eye”. For this reason carefully
knock on the “magic eye” before carrying out the check.•
Green colour - the battery is adequately charged.
•
Dark colour - the battery has to be charged
•
Colourless or yellow colour - have the battery checked by a specialist garage.
Batteries, which are more than 5 years old, must be replaced. We recommend you have the electrolyte level inspected and adjusted to the correct level or the battery replaced if necessary by
a specialist garage.
Caution
If the vehicle has not been driven for more than 3 to 4 weeks, the battery will discharge because certain electrical comp
onents consume electricity (e.g. control
units) also in idle state. You can prevent
the discharging of the battery by discon-
necting the negative terminal or charging
the battery constantly with a very low
charging current. Please also refer to
the notes when working on the battery
⇒ page 168, “Working on the battery”.
Inspecting the electrolyte levelThe battery is practically
maintenance-free
under normal operating conditions.
We do, however, recommend that you have
the electrolyte level inspected from
time to time by a specialist garage when outside temperatures are high or when driving on long trips. You should also have the electrolyte level
⇒page 170
checked each time the battery is charged. The electrolyte level of the battery will al
so be checked as part of the Inspection
Service.Operation in winterThe battery has to provide greater amounts of electricity during the winter. It also has only part of the initial power output at
low temperatures that it has at normal
temperatures. A discharged battery may already freez
e at temperatures just below 0°C.
We therefore recommend that you have the battery checked by a specialist garage before the start of the winter and recharged if necessary.
WARNING
Never charge a frozen or thawed battery - risk of explosion and caustic burns. Replace a frozen battery.Charging the battery A properly charged battery is essential for reliably starting the engine.– Read the warning notes
⇒
in “Working on the battery” on
page 168 and
⇒
.
– Switch the ignition and all electrical components off.
Fig. 157 Battery with a charge level indicator
s2g8.b.book Page 170 Tuesday, April 7, 2009 8:53 AM

Inspecting and replenishing
171
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Only for “quick-charging”: Disconnect
both battery cables (first of all
“negative”, then “positive”).
– Carefully attach the terminal clam
ps of the charger to the battery
terminals (red = “positive”, black = “negative”).
– You can now plug the mains cable of the charger into the power socket
and switch on the charger.
– When charging is completed: switch the charger off and unplug the
mains cable from the power socket.
– Only then should you disconnect the terminal clamps of the charger. – Reconnect the cables to the battery
(first of all “positive”, then “nega-
tive”).
It is not normally necessary
to disconnect the cables of the battery if you recharge
the battery using low ampera
ges (as for example from a
mini-charger
). Please also
refer to the instructions from the charger manufacturer. A charging current of 0.1 of the total batter
y capacity (or lower) is that which should
be used until full charging is achieved. It is, however, necessary to disconnect both
cables before charging the battery with
high amperages, so-called “
quick-charging
”.
“Quick-charging” a battery is
dangerous
⇒
in “Working on the battery” on
page 168. It requires a special charger and appropriate knowledge. We therefore recommend that you have your battery qu
ick-charged only by your specialist
garage. A discharged battery may already
freeze
at temperatures just below 0°C
⇒
. We
recommend that you no longer use a ba
ttery which has thawed out because the
casing of the battery may be cracked through the formation of ice and this would allow battery electrolyte to flow out. The vent plugs of the battery should not be opened for charging.
WARNING
Never charge a frozen or thawed battery - risk of explosion and caustic burns. Replace a frozen battery.Disconnecting and reconnecting the batteryOn disconnecting and reconnecting the battery the following functions are initially deactivated or are no longer able to operate fault-free. We recommend having the vehicle checked by
a specialist garage to ensure full
functionality of all electrical systems.Replacing the batteryYou should only replace a battery with a
new battery of the same capacity, voltage
(12 V), amperage and of the same size. Specialist garages have a range of suitable batteries available. We recommend that you only have an old ba
ttery disposed of by a specialist garage
since it does require special disposal.
For the sake of the environment
Batteries contain pois
onous substances such as sulphu
ric acid and lead. They must
be disposed of in accordance with loca
l environmental protection regulations and
on no account as domestic waste.Operation
Operating measure
Electrical power window
(operational faults)
⇒page 46
Enter radio code number
see Radio Operating Instructions
Set hours
⇒page 19
Data in the multi-functional indicator* are deleted.
⇒ page 19
s2g8.b.book Page 171 Tuesday, April 7, 2009 8:53 AM

Inspecting and replenishing
172
Windshield washer systemThe windshield washer reservoir contains
the cleaning fluid for the windscreen or
rear window. The reservoir is located at the front right of the engine compartment ⇒ fig. 158
.
The
filling level
of the container is 3 litres, 5.5 li
tres on vehicles which also have a
headlight washing system. Clear water is not sufficient to intensivel
y clean the windscreen
and headlights. We
therefore recommend using clean washing wa
ter together with the screen cleaner
from Škoda genuine accessorie
s (in winter additionally with antifreeze) which is
capable of removing stubborn dirt. Follow
the instructions for use on the packaging
when using screen cleaning products. You should always add antifreeze to the
cleaning water in wi
nter even if your
vehicle is fitted with heated windscreen washer nozzles*. It is also possible in exceptional cases to use methylated spirits when no screen cleaner with antifreeze is
available. The concentration
of methylated spirits must
not be more than 15 %. Please note, howeve
r, that the antifreeze protection at this
concentration is only adequate down to -5°C.
WARNING
Read and observe the warning notes
⇒page 160, “Working in the engine
compartment” before working in the engine compartment.
Caution
•
On no account should you add radiator
antifreeze or other additives to the
windscreen washer fluid.•
If the vehicle is fitted with headlight
cleaning system, you should only add
cleaning products which do not attack th
e polycarbonate coating of the headlights
to the windscreen washer fluid. Please contact your specialist garage, who will tell you which cleaning agent you can use.
Fig. 158 Engine compart- ment: Windshield washer fluid reservoir
s2g8.b.book Page 172 Tuesday, April 7, 2009 8:53 AM

Wheels and Tyres
173
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Wheels and TyresWheelsGeneral information•
New tyres do not offer optimal grip at first and should therefore be run in for
about 500 km at a moderate speed and an
appropriately cautious style of driving.
You will also profit from longer tyre life.•
The tread depth of new tyres may differ
because of design features and the
configuration of the tread (depending on
the type of tyre and the manufacturer).
•
Drive over curbs on the side of the road
and other such obstacles slowly and,
where possible, at a right angle in order to avoid damage to tyres and wheel trims.•
Inspect your tyres from time to time
for damage (punctures, cuts, splits and
bulges). Remove foreign bodies from the tyre profile.•
Damage to tyres and wheels is frequent
ly not visible. Unus
ual vibrations or
pulling of the vehicle to one side
could be a sign of tyre damage.
Please reduce
your speed immediately and stop if
you suspect that a wheel is damaged.

Inspect the tyres for signs of damage (bulges,
splits, etc.). If no
visible damage is
present, please drive at an appropriatel
y slow speed and carefully to the nearest
specialist garage in order to have your vehicle inspected.•
Also protect your tyres from contact with oil, grease and fuel.
•
Immediately replace any dust caps of the valves which have got lost.
•
Mark wheels before removing them so th
at their previous direction of running
can be maintained when mounted them again.•
Always store wheels or tyres which been removed in a cool, dry and, where
possible, dark place. Tyres which are not fixed to a wheel trim should be stored upright.
WARNING
•
New tyres during the first 500 km do not offer optimal grip and should
therefore be run appropriately - risk of accident!•
Never drive with damaged tyres - risk of accident!
Note
Please observe the various differing legal requirements regarding tyres.Tyre lifeThe life of your tyres very much depends on the following points: Tyre pressure The working life of tyres will be shortened considerably if the tyres are insufficiently or over-inflated and this will have an advers
e effect on the handli
ng of your vehicle.
Correctly inflated tyres are of partic
ular importance when travelling at
high speeds
.
It is therefore good to check the pressure at least once a month and also before setting off on a long trip. Please do not
forget the spare wheel* when checking the
tyres. The tyre inflation pressures for
summer tyres
are indicated on the inside of the fuel
filler flap
⇒fig. 159
. The inflation pressures for
winter tyres
are 20 kPa (0.2 bar)
higher than those for summer tyres
⇒page 177.
The tyre pressure should be at the highest
pressure specified for your vehicle at all
times.
Fig. 159 An opened fuel filler flap with a tyre size and tyre inflation pressure table
s2g8.b.book Page 173 Tuesday, April 7, 2009 8:53 AM

Wheels and Tyres
174
Always check the inflation pressure of ty
res when cold. Do not reduce the higher
pressure of warm tyres. Adapt the inflation pressure of the tyres accordingly if your vehicle is carrying a significantly higher payload. Driving style Fast cornering, sharp acceleration and braking (squealing tyres) increase wear-and- tear on your tyres. Balancing wheels The wheels of a new vehicle are balanced. There are a wide range of influences when driving which may result in an imbalance and which makes themselves felt through vibration in the steering. You should have the wheels rebalanced
since any imbalance increases wear-and-
tear on the steering, the suspension and
tyres. A wheel must also be rebalanced
when a new tyre is fitted and each time a tyre is repaired. Wheel alignment errors Incorrect wheel alignment at the front and re
ar will not only increase wear-and-tear
on the tyres but will also has an adverse
effect on vehicle safety. Contact your
specialist garage if you notice any unusual tyre wear.
WARNING
•
If the inflation pressure is too low,
the tyre must perform a greater flexing
work. At higher speeds the tyre will warm up as a result of this. This can result in tread separation and even a tyre blowout.•
Immediately replace the damaged rims or tyres.For the sake of the environment
Tyres which are insufficiently inflated increase your fuel consumption.
Wear indicatorsThe base of the tread of the original tyres has wear indicators 1.6 mm high, installed at right angles to the direction of travel. These wear indicators are located at 6 - 8 points depending on the make and are evenly spaced around the circumference of the tyre
⇒fig. 160
. Markings on the walls of the
tyres through the letters “TWI”,
triangular symbols or other symbols identi
fy the position of the wear indicators.
A remaining tread of just 1.6 mm, measured in the grooves of the tread next to the wear indicators, means that your tyres
have reached their legally permissible
minimum tread depth.
WARNING
•
You must have your tyres replaced with new ones at the latest when the
wear indicators have been worn do
wn. The legally permissible minimum
tread depth should be observed.•
Worn tyres do not provide the necessar
y adhesion to the road surface at
high speeds on wet roads. One coul
d experience “aquaplaning” (uncon-
trolled movements of the vehicle - “swimming” on a wet road surface).
Fig. 160 Tyre tread with wear indicators
s2g8.b.book Page 174 Tuesday, April 7, 2009 8:53 AM

Wheels and Tyres
175
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Changing wheels aroundIf significantly greater wear is present on the front tyres, we recommend changing the front wheels around with the rear wheels as shown in the diagram
⇒fig. 161
.
You will then obtain approximately the same life for all the tyres. It may be advantageous to swap the tyre
s over “crosswise” when certain types of
wear characteristic arise on
the running surface of the tyres (but not in the case of
unidirectional tyres). Specialist garages are familiar with details. We recommend that you change the wheels around every 10 000 km in order to achieve even wear on all wheels and to obtain optimal tyre life.New tyres and wheelsTyres and wheel rims are important design
elements. One should therefore use the
tyres and wheel rims which have been released for use by Škoda Auto. They are exactly matched to the vehicle type and th
erefore contribute significantly to good
road holding and safe driving characteristics
⇒
.
Only fit radial tyres of the same type on
all 4 wheels, size (rolling circumference)
and, if possible, the same tread pattern on one axle. The specialist garages have access to the most current information about which tyres we have released
for use on your vehicle.
We recommend that you have any work rela
ting to tyres or wheels carried out by a
specialist garage
. Specialist garages have all of the necessary special tools and
replacement parts available plus the requir
ed specialist knowledge and are also in
a position to properly dispose of the old tyres. A large number of specialist garages also have an attractive range of tyres and wheels available. The tyre/wheel combinations which are appr
oved for your vehicle are indicated in
your vehicle documents. Approval and lice
nsing may differ according to the legis-
lation prevailing in individual countries. Proper knowledge of the tyre data makes it easier for you to select the correct type of tyre. Tyres do, for example, have the following
inscription
on their walls:
195 / 65 R 15 91 T
What this means is: The following
speed restrictions
apply to tyres.
Fig. 161 Changing wheels around
195
Tyre wid th i n m m
65
Height/width ratio in %
R
Code letter for the type of tyre -
R adial
15
Diameter of wheel in inches
91
Load index
T
Speed symbol
Speed symbol
Permissible maximum speed
R
170 km/h
S
180 km/h
T
190 km/h
H
210 km/h
V
240 km/h
W
270 km/h
s2g8.b.book Page 175 Tuesday, April 7, 2009 8:53 AM