2009 SKODA OCTAVIA TOUR Owner's Manual

Taking care of your vehicle and cleaning the vehicle
152
Engine compartmentGood corrosion protection is very importan
t, particularly in winter when one often
drives over its salt-strewn roads. One should therefore clean the whole engine compartment before and after the salt spre
ading period and treat with preservative
in order to prevent the salt from being destructive. Specialist garages have the cleaning agents and preservatives recommended by the manufacturer and also the required equipment.
WARNING
•
It is necessary to observe the guidelines given in the chapter before
working on the engine compartment
⇒page 160.
•
Let the engine cool down before
cleaning the engine compartment.
Caution
•
Engine cleaning may be only be und
ertaken when the ignition is off.
•
It is recommended to cover the generator before washing the engine compart-
ment.
For the sake of the environment
The dirty water produced by
washing the engine has washed away petrol, and resi-
dues of grease and oil and should therefor
e be cleaned by an oil separator. This is
why engine washing should only be undertake
n in a specialist garage or at a fueling
station (when these are fitted with the required equipment).Care of the interior of vehiclePlastic parts, artificial leather and clothsYou can clean plastic parts and
artificial leather with a moist cloth. You should only
treat such parts with special
solvent-free plastic cleaning and care products
it
does prove to be adequate.
Upholstery cloth and cloth trim on the
doors, luggage compartment cover, head-
liner etc. are best treated with special
cleaning products, using if necessary a
dry
foam
and a soft sponge or brush.
We recommend using a cleaning product
from Škoda genuine accessories offered
by your Škoda dealer.
Caution
Solvent-free cleaners attack the material and can damage it.Fabric covers of electrically heated seatsDo
not clean
the seat covers moist as this may result in damage to the seat heating
system. Clean such covers using special agents, for example dry foam.Natural leather Natural leather requires quite particular care and attention.Leather should be treated from time
to time according the following
guidelines depending on how much it is used. Normal cleaning – Clean soiled areas of the leather
with slightly moistened cotton or
woollen cloth.
Severe soiling – Clean severely soiled areas with a cloth dipped in a mild soapy solu-
tion (2 spoonfuls of natural soap to 1 litre of water).
– Ensure that the leather is not soaked through at any point and that no
water gets into the stitching of the seams.
– Dry off the leather with a soft, dry cloth.
s2g8.b.book Page 152 Tuesday, April 7, 2009 8:53 AM

Taking care of your vehicle and cleaning the vehicle
153
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Removing stains – Remove fresh stains which are
water-based
(e.g. coffee, tea, juices,
blood etc.) with an absorbent cloth or household paper or use the cleaner from the care set for a
stain which has already dried in.
– Remove fresh stains on a
fat base
(e.g. butter, mayonnaise, chocolate
etc.) with an absorbent cloth or household cleaning paper or with the cleaner from the care set if the stain has not yet penetrated into the surface.
– Use a grease dissolver for
grease stains which have dried in
.
–Eliminate
special stains
(e.g. ball-point pens, felt pen, nail varnish,
dispersion paint, shoe cream etc.) with a special stain remover suit-able for leather.
Leather care – Treat the leather every six months with the leather care product avail-
able from specialist garages.
– Apply only a small amount of the care product.– Dry the leather off with a soft clothWe recommend that you consult a speciali
st garage if you have any questions
regarding cleaning and care of the
leather interior in your vehicle.
Caution
•
You must on no account treat the leather with solvents (e.g. gasoline, turpen-
tine), floor wax, shoe cream or such like.•
Avoid leaving your vehicle for lengthy pe
riods in bright sunlight in order to
avoid bleaching the leather. If
you leave your vehicle parked in the open for lengthy
periods, protect the leather from the direct
rays of the sun by covering it over.
•
Sharp-edged objects on items of clothing
such as zip fasteners, rivets, sharp-
edged belts may leave permanent scratche
s or signs of rubbing on the surface.
Note
•
Use a care cream with light blocker and impregnation effect regularly and each
time after cleaning the leather. The cream no
urishes the leather, allows it to breathe
and keeps it supple and also provides moisture. It also creates surface protection.•
Clean the leather every 2 to 3 months, remove fresh soiling each time this
occurs.•
Remove fresh stains such as those from
ball-point pens, ink, lipstick, shoe
cream etc., as quickly as possible.•
Care also for the leather dye. Refreshen
areas which have lost their colour with
a special coloured leather cream as required.•
The leather is a natural material with specific properties. During the use of the
vehicle, minor optical change
s can occur on the leather parts of the covers (e. g
wrinkles or creases as a result of the stress of the covers).Seat belts– Keep the seat belts clean! – Wash seat belts which have become
soiled using a mild soapy solu-
tion.
– Inspect the seat belts regularly to
ensure they are in good condition.
Belt webbing which has become severely so
iled may prevent the inertia reel from
reeling up the belt properly.
WARNING
•
The seat belts must not be removed for cleaning.
•
Never clean the seat belts chemically
as dry cleaning may destroy the
fabric. The seat belts must also not be allowed to come into contact with corrosive liquids (such as acids etc.).•
Seat belts which have damage to
the webbing, the connections, the
inertia reel or the lock should be
replaced by a specialist garage.
s2g8.b.book Page 153 Tuesday, April 7, 2009 8:53 AM

Taking care of your vehicle and cleaning the vehicle
154
•
Inertia reel belts must be complete
ly dried before being reeled up.
WARNING (continued)
s2g8.b.book Page 154 Tuesday, April 7, 2009 8:53 AM

Fuel
155
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
FuelPetrolGrades of petrolThere are various grades of petrol. Please
check in order to know which grade of
petrol your vehicle requires.
You will also find the same information affixed to the
inside of the fuel filler flap of your vehicle
⇒page 156.
A distinction is made between unleaded an
d leaded petrol. All Škoda vehicles with
petrol engines are equipped with a catalyti
c converter and must therefore be only
driven with
unleaded petrol
. Unleaded petrol complies with the
standard EN 228
.
The individual grades of petr
ol are distinguished by their
octane number
(RON).
Please adopt the following procedure if the grade of petrol which you normally use is not be available in
exceptional circumstances:
•
Engines which need
unleaded premium petrol 95 RON
can also be run on
unleaded regular petrol 91 RON. This does, however, result in a slight loss in performance.•
Engines which need
unleaded premium plus 98 RON
can also be run on
unleaded premium petrol 95 RON. This coul
d result in a slight loss in engine
performance. You can
in case of need
also use unleaded regular petrol 91 RON in
the event that neither unleaded premiu
m plus 98 RON nor unleaded premium
petrol 95 RON is available. Refuel as soon as possible with unleaded premium plus 98 RON or unleaded premium petrol 95 RON. If, in an emergency, the only fuel availa
ble is one which has a lower octane number
than that required by the engine then only drive at medium engine speeds and lower engine loadings. You can make unlimited use of fuel whic
h has a higher octane
number than that
required by the engine. There will, howeve
r, be no advantages gained by this in
terms of engine performance and fuel consumption! The handling, performance and
life of your engine are determined to a significant
extent by the quality of the fuel.
Do not use any petrol additives.
Use a fuel
complying with
the standard.
You can find further information on refuelling
⇒page 156, “Refuelling”.
Caution
•
Filling the tank even only once with lead
ed petrol will result in the catalytic
converter being destroyed.•
Operating the engine with petrol of a lo
w octane number can result in engine
damage at high revolutions or severe engine loading.DieselDiesel fuelYour vehicle can be operated with
diesel fuel
, which complies with the standard
EN 590
.
Fuel additives You must not use fuel additives, so-called “flow improvers” (petrol and similar products) in diesel fuel. If the quality of the diesel fuel is poor, it is then necessary to drain the
fuel filter

more often than stated in the Service schedule. You can find information on refuelling
⇒page 156, “Refuelling”.
Caution
•
Use fuel which complies with the standard
DIN EN 590
. Filling the tank even
only once, which does not comply with th
e standard, can result
in damage to the
fuel system.•
Water which has collected in the fuel fi
lter can result in engine problems.
•
Your vehicle is not adapted
for use of biofuel (RME), therefore this fuel must not
be refuelled and driven. Using this fuel (RME) can lead to damage to the engine or the fuel system.
s2g8.b.book Page 155 Tuesday, April 7, 2009 8:53 AM

Fuel
156
Operation in winterWinter-grade diesel fuel A different grade of diesel fuel is available at
filling stations in winter than during the
summer. Using “summer-grade diesel fuel” at
temperatures below 0°C can result in
operational problems because the diesel be
comes viscous as a result of paraffin
separation. It is therefore the case that EN 590 prescribes diesel fuel class for certain periods of the year which can also be purchased at
the corresponding time during the year.
“Winter-grade diesel fuel” will still operate properly even at a temperature of -20°C. It is often the case in countries with diff
erent climatic conditions that diesel fuels
available have a different temperature characteristic. The specialist garages and the filling stations in the country concerned wi
ll be able to provide you with informa-
tion regarding the diesel fuels available. Prewarming fuel The vehicle is fitted with a fuel filter prewarming system. This secures operation of a vehicle using diesel fuel down to an environmental temperature of -25°C.
Caution
It is not permitted to add the various fuel
additives on the market, including petrol,
to diesel fuel in order to
improve its flow properties.
RefuellingThe filler tube of the fuel reservoir is
located in the rear right side part of
the vehicle. Opening the fuel filler cap – Open the fuel filler flap with the hand. – On vehicles without remote unlocking
of the fuel filler flap from the
driver's seat, unlock the fuel filler cap on the fuel filler tube by turning the vehicle key to the left.
Fig. 145 Switch for opening the fuel filler flap from the driver seatFig. 146 Fuel filler flap with cap unscrewed
s2g8.b.book Page 156 Tuesday, April 7, 2009 8:53 AM

Fuel
157
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Unscrew the fuel filler cap anti-cl
ockwise and place the fuel filler cap
from above on the fuel filler flap
⇒
page 156, fig. 146
.
Closing fuel filler cap – Screw on the cap by turning it to the right until it is heard to lock. – On vehicles without remote unlocking of the fuel filler flap from the
driver's seat, lock the fuel filler cap on the fuel filler tube by turning the vehicle key to the right and withdraw the key.
– Close the fuel filler flap until it locks. Open the fuel filler flap from the driver's seat* – Press the switch to open the fuel filler flap
⇒
page 156, fig. 145
.
– Unscrew the fuel filler cap anti-cl
ockwise and place the fuel filler cap
from above on the fuel filler flap
⇒
page 156, fig. 146
.
Closing fuel filler cap – Screw on the cap by turning it to the right until it is heard to lock. – Close the fuel filler flap until it locks.The correct grade of fuel for your vehicle as
well as the tyre size and inflation pres-
sures are stated on a sticker affixed to the
inside of the fuel filler flap. Further infor-
mation on fuel
⇒page 155, “Fuel”.
The fuel tank has a capacity of about 55 litres.
WARNING
Pay attention to any legal requirements if
you do carry a spare canister in the
vehicle. We do not recommend carrying any fuel canisters in your vehicle for safety reasons. The canister can be da
maged in the event of an accident and
fuel may leak out.
Caution
•
Before refuelling it is necessary to switch off the auxiliary heating system (auxil-
iary heating and ventilation) *.•
Remove any fuel which has spilled onto
the paintwork of your vehicle immedi-
ately - risk of paint damage!•
On vehicles fitted with a
catalytic converter, never let the fuel tank run
completely empty. An irregular supply of fu
el to the engine can result in misfiring
and unburnt fuel may get into the exhaust system, which may result in overheating and damage to the catalytic converter.•
Make sure that the valve is not pressed
into the filler tube when inserting the
pump nozzle into the filler tube. Otherwis
e you are unintentionally filling up the
volume, which in case of heat can cause an
expansion of the fuel. This can lead to
an overflow of fuel or damage
to parts of the fuel reservoir.
•
The fuel tank is full just as soon as the pump nozzle switches off for the first time,
provided the nozzle has been operated pr
operly. Do not continue refuelling -
otherwise the expansion volume is filled up.Emergency release of fuel filler flapIf a fault exists in the system for opening the fuel filler flap from the driver's seat*, the fuel filler flap can be opened manually.
Fig. 147 Luggage compart- ment: Emergency release of fuel filler flap
s2g8.b.book Page 157 Tuesday, April 7, 2009 8:53 AM

Fuel
158
Unlocking – Open the boot lid and remove the right inner paneling. – Pull on the control cable in direct
ion of arrow in order to unlock the
fuel filler flap
⇒
page 157, fig. 147
.
WARNING
When unlocking the fuel fi
ller flap manually, pay at
tention to sharp edges of
the body - risk of injury.s2g8.b.book Page 158 Tuesday, April 7, 2009 8:53 AM

Inspecting and replenishing
159
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Inspecting and replenishingEngine compartmentBonnet remote releaseBonnet remote release – Pull the unlocking lever below the
dash panel on the driver's side
⇒
fig. 148
.
The bonnet jumps out of its lock as a result of the spring force.
Note
Ensure that the windscreen wiper arms
are not folded out before opening the
bonnet otherwise damage coul
d occur to the paintwork.
Opening and closing the bonnet.Opening the bonnet – Unlock the bonnet
⇒
fig. 148
.
– Grip with the hand under the radiat
or grille and lift up the bonnet.
– Press the locking lever in direction of arrow
⇒
fig. 149
and lift up the
bonnet.
Fig. 148 Bonnet release lever
Fig. 149 Radiator grille: Locking leverFig. 150 Securing the bonnet with the bonnet support
s2g8.b.book Page 159 Tuesday, April 7, 2009 8:53 AM