2009 SKODA OCTAVIA TOUR remove seats

Seats and Storage
64
Information concerning the off switch of the memory systemAfter pressing the off switch of the memory system
⇒page 62, fig. 61
, the
memory system is deactivated. You can only adjust the seat and the exterior mirrors manually. You can switch on the memory sy
stem again by once
again pressing the
off switch of the memory system. The setting is not carried out to the end if a retrieved setting operation is interrupted. We recommend that you switch off the memory system with the off switch if the vehicle is used for a short period by a driver and you do not wish to store any partic-ular settings of the seat and mirrors in this case.Head restraints
Best protection is achieved if the top
edge of the head restraint is at the
same level as the upper part of your head. Adjusting the height of a head restraint – Grasp the side of the head restraint with both hands and push it up or
down in direction of arrow
⇒
fig. 62
.
Adjusting the angle of a head restraint – The head restraint can be matched
to the head of the occupant by
adjusting the angle in the direction of the arrow
⇒
fig. 62
.
Adjusting the angle of the head re
straint provides enhanced comfort
for the user.
Removing and installing a head restraint – Pull the head restraint out of the
seat backrest as far as the stop.
– Press the locking button in the direction of arrow
⇒
fig. 63
and pull
the head restraint out.
– To re-insert the head restraint, push it down into the seat backrest far
enough until you hear the locking button engage.
The head restraints must be adjusted to
match the size of the seat occupant.
Correctly adjusted head restraints togeth
er with the seat belts offer effective
protection for the occupants
⇒page 104.
WARNING
•
The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.•
Do not drive under any circumstance with removed head restraints - risk
of injury!
AE
AE
AE
AE
Fig. 62 Adjusting head restraintFig. 63 Removing a head restraint
AA
AB
s2g8.b.book Page 64 Tuesday, April 7, 2009 8:53 AM

Seats and Storage
65
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Rear seatsFolding the rear seats forwardsThe luggage compartment can be increased in size by folding the rear seats forwards. Before folding the rear seats forwards, it is required to adapt the position of the front seats and the armrest in such a way that no mutual deformation or damage can occur to the seats.
Folding seats forwards – Before folding the rear seats forwards, you must adapt the position of
the front seats in such a way that
they are not damaged when the rear
seats are folded forwards.
– Pull up the seat cushion in direction of arrow and fold forwards in
direction of arrow
⇒
fig. 64
.
– Unlock the seat backrests by
pulling the securing knob
⇒
fig. 65
and
fold them forwards.
– Remove the head restraints from the seat backrests and fold the back-
rests completely forwards.
– The head restraints can be inserted into the relevant holes of the
folded forward seat cushions.
If the front seats are too far back, we
recommend that you have the rear head
restraints removed before the seat backrests are folded forward. Store the removed head restraints in such a way that they cannot be damaged or soiled. Please refer to the guidelines
⇒page 68, “luggage compartment”.
Move seats into th
e initial position
Fig. 64 Folding the seat cushion forwardsFig. 65 Unlock the seat back-rest
A1
A2
Fig. 66 Lock the seat back-rest
s2g8.b.book Page 65 Tuesday, April 7, 2009 8:53 AM

Seats and Storage
66
Move seats into the initial position – Install the head restraints in the slightly lifted seat backrest. – Place the rear lateral seat belt behind the edge of the side trim
panel
⇒
page 65, fig. 66
.
– Then push the seat backrest back
into the upright position until the
securing knob clicks into place - ch
eck by pulling on the seat backrest.
– Move the seat cushion into its original position.
WARNING
•
The belts and the belt locks must be in
their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.•
The seat backrests must be securely interlocked in position so that no
objects in the luggage compartment ca
n slide into the passenger compart-
ment if there is sudden braking - risk of injury!•
Pay attention that the seat backrests are correctly interlocked. It is only
then that the three-point seat belt for the middle seat can reliably fulfil its function.•
Before folding the seat backrest back
into the secure position, place the
rear lateral seat belt behind the edge of the side trim panel. Take suitable measures to prevent that the seat belt
is jammed between the seat backrest
and the side trim panel and is thus damaged.
Removing the seat cushionThe luggage compartment can be increased further in size by removing the rear seat. Removing – Fold the seat cushion forwards completely. – Press the wire clamps in the direction of the arrow
⇒
fig. 67
and
remove the seat cushion from its holder.
Installing – Press the wire clamps in the direction of the arrow and place it in its
holder.
– Fold the seat cushion back into its original position.
AA
Fig. 67 Removing seat cush- ions
s2g8.b.book Page 66 Tuesday, April 7, 2009 8:53 AM

Seats and Storage
71
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Luggage compartment cover (Octavia) You can use the luggage compartment cover behind the head restraints for storing
light and soft items.
The luggage compartment cover can be
removed as required if one must
transport bulky goods. – Unhook the support stra
ps on the boot lid
⇒
fig. 76
.
– Place the cover in the horizontal position. – Pull the cover out of the holder horizontally to the rear.– Install again by pushing the luggage
compartment cover forwards into
the holder and hanging the suppo
rt straps on the boot lid.
You can stow the removed luggage compartment cover behind the rear seat back- rest.
WARNING
No objects should be placed on the
luggage compartment cover, the vehicle
occupants could be endangered if th
ere is sudden braking or the vehicle
collides with something.
Caution
Please ensure that the heating elements of the rear window heater are not damaged as a result of obje
cts placed in this area.
Note
Opening the tailgate also lifts up the luggage compartment cover.Foldable luggage compartment cover (Combi)Pulling out – Pull the foldable luggage compartment cover in direction of arrow
⇒
fig. 77
.
– Hang the luggage compartment cover in the recesses on the side of
the luggage compartment.
Folding – Pull the foldable cover out of the recesses, the cover is folded up.
Fig. 76 Removing the luggage compartment coverA1
A2
A2
A1
Fig. 77 Luggage compart-ment: removing the foldable luggage compartment cover
s2g8.b.book Page 71 Tuesday, April 7, 2009 8:53 AM

Seats and Storage
72
Removing – Have the foldable luggage compartment cover removed to transport
bulky goods by pressing the slider
from the side in the direction of
arrow and removing the cover in the direction of arrow ⇒
page 71, fig. 77
.
WARNING
No objects should be placed
on the luggage compartment cover.
Caution
Please ensure that the heating elements of the rear window heater and the foldable luggage compartment cover are not damaged as
a result of objects placed in this
area.Variable loading floor* (Combi)
The variable loading floor makes it
easier to handle bulky goods and
creates an even luggage compartmen
t floor when the rear seats are
folded forward. The maximum permissa
ble surface load of the variable
loading floor is 75 kg. Remove variable loading floor – Unlock the loading floor by turning the locking bolts by approx. 90°
to the left
⇒
fig. 78
.
– Fold together the loading floor and take it out by moving in direction
of arrow.
Install carrier rails – Unlock the carrier rails by turn
ing the arbor-mounted fixing eyes
to the right by approx. 90°
and take out the carrier rails.
Install carrier rails – Place the carrier rails in the original position and attach them with
the aid of the mountable fixing eyes by turning to the left by approx. 90° at the fixed eyes of the body.
Install variable loading floor – Place the loading floor once folded together onto the carrier rails.
A1
A2
Fig. 78 Variable loading floor
Fig. 79 Luggage compart-ment: Remove carrier rails
AA
AB
AC
AB
AC
s2g8.b.book Page 72 Tuesday, April 7, 2009 8:53 AM

Seats and Storage
73
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Fold open the loading floor. – Lock the loading floor by turning
the locking bolts by approx. 90°
to the right.
WARNING
Pay attention when installing that the
carrier rails and the variable loading
floor are correctly fixed, otherw
ise the occupant
s are at risk.
Divide the luggage compartmen
t with variable loading floor*
The luggage compartment can be divided with the variable loading floor. – Lift up a part of the loading floor with the handle and secure it by
moving it into the grooves
⇒
fig. 80
.
Net partition (Combi)*Use the net partition behind the rear seatsThe net partition can either be insta
lled behind the rear seats or behind
the front seats. Before using the net partition, remove the foldable cover ⇒
page 71.
Pulling out – Pull the net partition out of the hous
ing at an angle of about 45° in
direction of the boot lid at the loop .
– Insert the cross rod into the mount first on the one side and push
the cross rod forward.
– In the same way, fix the cross rod to the other side of the vehicle,
mount .
Folding – Push the cross rod first of all on the one side and then on the other
side towards the rear.
– Take the cross rod out of the mounts .
AA
Fig. 80 Divide the luggage compartment
Fig. 81 Pull out net partition
AB
AAAC
AC
AC
s2g8.b.book Page 73 Tuesday, April 7, 2009 8:53 AM

Seats and Storage
76
Lashing points (Octavia)Fitting – The plastic caps
⇒
fig. 85
can be removed by inserting a thin screw-
driver into the recess of the caps and carefully lever out the caps to avoid paint damage.
– The feet are inserted into the openings of the roof bars.
Note
•
Pay attention to the information regarding assembly and disassembly in the
attached instructions.•
If you have any questions, plea
se contact a specialist garage.
•
The figure is not valid for an estate car.
Roof loadDistribute weight evenly over the roof
luggage rack system. The maximum permis-
sible roof load (including roof rack system) of
75 kg
and the maximum permissible
total weight of the vehicl
e should not be exceeded.
You cannot make full use of the permissible roof load if you use a roof luggage rack system with a lower load
carrying capacity.
The load transported on the roof
luggage rack system must not exceed the weight limit which is stated in the fitting instructions.
WARNING
•
The items which you transport on the roof bar system must be reliably
attached - risk of accident!•
You must on no account exceed the permissible roof load, the permis-
sible axle loads and the permissible gros
s weight of your vehicle - risk of
accident!•
Please note that the handling prop
erties of your ve
hicle change when
you transport heavy or bulky items on the roof bar system as a result of the displacement of the centre of gravity and the increased wind attack area - risk of accident! You must absolutely adapt your style of driving and the speed of the vehicle to the specific circumstances.Cup holder in front centre consoleAfter pressing in direction of arrow,
the cup holder slides out and opens up
⇒ fig. 86
.
It is designed to place drink cans or other beverage packagings in (with a content of 0.33°ltr. or 0.5°ltr.).
Fig. 85 Attachment points for base roof carrier
Fig. 86 Front centre console: Cup holder
s2g8.b.book Page 76 Tuesday, April 7, 2009 8:53 AM

Seats and Storage
77
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
•
Do not place any hot beverages into th
e cup holder. If the vehicle moves,
the hot beverages may spill - risk of scalding!•
Do not use any cups or beakers which
are made of brittle material (e.g.
glass, porcelain). You might be injured
by them in the event of an accident.
Caution
Do not open the beverages in the cup holder while driving. They may spill when braking and while doing so damage the vehicle.Note holderThe note holder is designed e.g. for atta
ching a car park ticket in parking areas.
The attached note has to always be
removed
before starting off in order not to
restrict the driver's vision.
Ashtray*Front ashtrayOpening ashtray – Press on the bottom part of the cover of the ashtray at the point of the
arrow
⇒
fig. 88
.
Removing ashtray insert – Remove the ashtray insert in direction of arrow .
Fig. 87 Windscreen: Note holder
Fig. 88 Centre console: Front ashtrayFig. 89 Remove ashtray and replaceAA
s2g8.b.book Page 77 Tuesday, April 7, 2009 8:53 AM