2008 PONTIAC G8 Owners Manual

Driver Information
Center (DIC)
The DIC displays information about
your vehicle. It also displays warning
messages if a system problem is
detected. The DIC also allows some
features to be customized. SeeDIC
Vehicle Customization on page 4-32
for more information. All messages
will appear in the DIC display located
in the center of the instrument panel
cluster.
When the ignition is turned on, a
vehicle system check is performed
and the status is shown on the
DIC display. If there are no warnings
or service reminders, the display
shows a series of welcome screens.
When the ignition is turned off,
the odometer appears on the display
for a short period of time unless a
service reminder is active. Active
service reminders are displayed for
10 seconds before the odometer
appears. The odometer will
reappear on the display when the
driver door is opened. For moreinformation on the warnings and
messages seeDIC Warnings
and Messages on page 4-27.DIC Operation and
Displays
The DIC has different displays
which can be accessed by pressing
the DIC buttons located on the
left side of the steering wheel. The
DIC displays trip, fuel, vehicle
system information, and warning
messages if a system problem
is detected.
DIC Buttons
3(Trip/Fuel):Press this button
to go through the displays and
the select the information.
QR(Thumbwheel):Use the
thumbwheel to scroll through
the available options.
8(ENTER to Reset/Select):Press
the thumbwheel to set or reset
certain functions and to turn off or
acknowledge messages on the DIC.
Trip/Fuel Menu Items
Press3to scroll through the
following menu items:
Speedometer
UNITS
Tire Pressure
Customize Options
Odometer/Trip Odometer
Distance/Time To Go
Range
Avg (Average)Speed/Avg
(Average) Fuel
OverSpeed
Instruments and Controls 4-23
2008 - Pontiac G8 Owner Manual

Speedometer
Press
3until the speedometer is
displayed.
The speedometer shows how fast
the vehicle is moving in either miles
per hour (MPH) or kilometers per
hour (km/h). To switch between
English and metric measurements,
see “UNITS” later in this section.
The digital speedometer display can
be enabled or disabled. See
“Digital Speedometer” underDIC
Vehicle Customization on page 4-32
for more information.
UNITS
Move the thumbwheel up
Qor down
Rto highlight English or Metric
when the UNITS display is active.
Press
8to conrm the setting. This
will change the displays on the
cluster, DIC, and the temperature
display in the mirror to either English
or metric measurements.Tire Pressure
Press
3until Tire Pressure is
displayed.
The display will show a vehicle and
the approximate pressures of all
four tires. Tire pressure is displayed
in either pounds per square
inch (PSI) or in kilopascal (kPa).
This display can be customized. See
DIC Vehicle Customization on
page 4-32for more information.
Customize Options
SeeDIC Vehicle Customization on
page 4-32for more information.
Odometer/Trip Odometer
Press
3until the Odometer/Trip
Odometer is displayed.
The odometer display shows the
distance the vehicle has been driven
in either miles (MI) or kilometers
(km). To switch between English
and metric measurements, see
“UNITS” earlier in this section.The Trip Odometer display shows
the current distance traveled
since the last reset for the trip
odometer. The trip odometer can be
reset to zero by pressing and
holding
8while the trip odometer
value is highlighted. If
8is only
pressed briey, the Avg Speed/Avg
Fuel will be reset as well.
Distance/Time To Go
Press
3until To Go is displayed.
If this item doesn’t display, check
that the display is turned on through
the Customize Options menu.
SeeDIC Vehicle Customization on
page 4-32for more information.
At the start of a trip, estimate
the distance to arrival (for example,
from maps, road signs). Move
the thumbwheel up or down until the
display shows the estimated trip
4-24 Instruments and Controls
2008 - Pontiac G8 Owner Manual

distance. When driving, the
computer constantly updates the
time to arrival, based on changing
driving speeds. Use the thumbwheel
to adjust the distance any time
this display is shown. Time to go is
shown in hours and minutes and
is only shown if the distance to go is
more than zero.
This display can be turned on or off
and the default setting can be
changed.
Range
Press
3until Range is displayed.
This display shows the approximate
distance the vehicle can be
driven without refueling. The fuel
range estimate is based on an
average of the vehicle’s fuel
economy over recent driving history
and the amount of fuel remaining
in the fuel tank. Fuel range cannot
be reset.Avg (Average)Speed/Avg
(Average) Fuel
Press
3until Avg Speed/Avg
Fuel is displayed.
Avg Speed shows the average
speed (while the engine is running)
since the last reset.
Avg Fuel shows average fuel used
since the last reset.
To reset only the Avg Speed or Avg
Fuel, press and hold
8while
either value is highlighted. If
8is
only pressed briey, the Trip
Odometer will be reset as well.OverSpeed
OverSpeed allows the driver to set
a speed that they do not want
to exceed. OverSpeed will illuminate
in the display and a chime will
sound to warn that the vehicle’s
speed is equal or has exceeded the
preselected value. During an
OverSpeed warning, the OverSpeed
display is shown, allowing the
driver to make adjustments.
To set the OverSpeed warning
press3when OverSpeed
is displayed to highlight the
OverSpeed mode. Move the
thumbwheel up
Qor downRto
scroll through and highlight one
of the following options:
Off:No OverSpeed warning set.
Manual:Allows you to manually set
the OverSpeed warning. See
“Manual OverSpeed” following.
Preset 1:Default setting 30 MPH
(48 km/h)
Instruments and Controls 4-25
2008 - Pontiac G8 Owner Manual

Preset 2:Default setting 45 MPH
(72 km/h)
Preset 3:Default setting 55 MPH
(89 km/h)
Preset 4:Default setting 70 MPH
(113 km/h)
The selection is set automatically
after a few seconds.
The corresponding value of the
presets will be shown on the display.
The preset OverSpeed warnings
can be reprogrammed. See
“Programming the OverSpeed
Presets” later in this section.
Manual OverSpeed
To manually set the OverSpeed
warning:
1. Use the thumbwheel to select
Manual for OverSpeed.
2. Press
8to highlight the current
value.3. Use the thumbwheel to adjust
the value in 5 MPH or km/h
increments and press
8
to conrm the setting.
To set the OverSpeed warning to
the vehicle’s current speed:
1. Use the thumbwheel to select
Manual as described in the
OverSpeed section.
2. Press
8to highlight the current
value.
3. Press and hold
8for more than
3 seconds to set the value to
the nearest 5 MPH or km/h
above the current vehicle’s
speed.
Programming the OverSpeed
Presets
While the vehicle’s speed is 6 MPH
(10 km/h) or below, each of the
presets can be altered and values
can be stored for future use.To reprogram the OverSpeed
presets:
1. Use the thumbwheel to select the
desired preset and press
8.
2. Move the thumbwheel up
Qor
down
Rto adjust the value in
1km/h increments.
3. Press
8to conrm the setting.
Adjusting the Setting During
an OverSpeed Warning
While the OverSpeed warning is
displayed move the thumbwheel up
Qor downRto adjust the
value when in Manual mode or to
select a different preset when
in Preset mode. Press and hold
8
for more than 3 seconds to set
the value to the nearest 5 MPH or
km/h above the current vehicle’s
speed. If Preset mode was selected,
this will change it to Manual mode.
4-26 Instruments and Controls
2008 - Pontiac G8 Owner Manual

Underspeed Chime
If an OverSpeed warning appeared
and the vehicle’s speed drops
below the set value, you will hear a
chime. The underspeed chime
can be turned on or off through the
vehicle customization. SeeDIC
Vehicle Customization on page 4-32
for more information.
DIC Warnings and
Messages
Messages are displayed on the DIC
to notify the driver that the status
of the vehicle has changed and that
some action may be needed by
the driver to correct the condition.
Multiple messages may appear one
after another.
Some messages may not require
immediate action, but you can press
3or8to acknowledge that
you received the messages and to
clear them from the display.
Some messages cannot be cleared
from the DIC display becausethey are more urgent. These
messages require action before they
can be cleared. You should take
any messages that appear on
the display seriously and remember
that clearing the messages will
only make the messages disappear,
not correct the problem.
The following are the possible
messages that can be displayed
and some information about them.
!ABS Fault
This message is displayed if there is
a problem with the ABS system.
The ABS light may also turn on in
the instrument panel cluster.
SeeAntilock Brake System (ABS)
Warning Light on page 4-17.
When this message is on, the brake
system will still operate with the
antilock operation disabled.
See your dealer/retailer.
uActive Select On
This message is displayed when the
automatic transmission active
select mode is enabled. See “Active
Select Mode” underAutomatic
Transmission Operation on
page 8-6.
9Airbag Fault
This message is displayed if there is
a problem with the airbag system
or safety belt pretensioner system.
SeeAirbag System on page 1-19
and “Safety Belt Pretensioners”
underLap-Shoulder Belt on
page 1-14. The Airbag Readiness
light may also come on in the
instrument panel cluster. SeeAirbag
Readiness Light on page 4-13.
See your dealer/retailer.
Instruments and Controls 4-27
2008 - Pontiac G8 Owner Manual

{Alarm Activated
This message is displayed when the
content theft-deterrent system
was activated by an attempted
break-in. The messages may also
include the location on the
vehicle where the break-in was
attempted. SeeContent
Theft-Deterrent on page 2-13for
more information.
"Alternator
This message is displayed if there is
a problem with the battery charging
system. The charging system
light may also come on in the
instrument panel cluster. See
Charging System Light on
page 4-15. Driving while this
message is on could drain the
battery. Turn off all unnecessary
accessories. Have the electrical
system checked as soon as
possible. See your dealer/retailer.
Battery Saver Mode On
This message is displayed when the
battery voltage level is low.
$Brake
This message is displayed if there is
a problem with the brake system.
The Brake System Warning
light may also come on in the
instrument panel cluster. SeeBrake
System Warning Light on
page 4-16. When this message is
on, stop the vehicle on the side
of the road. Do not continue driving
until you know that braking is
possible or that the cause of the
problem has been corrected,
see your dealer/retailer. This
message also indicates low brake
uid. Check the brake uid level.
SeeBrakes on page 9-24.
*Check Engine
If this message and the Malfunction
Indicator Lamp come on and
stay on when driving, the system
may require servicing. Although the
vehicle may still be drivable and
not require towing, take the vehicle
to your dealer/retailer as soon
as possible. If this message comes
on when the Malfunction Indicator
Lamp is ashing, reduce the
vehicle’s speed and load until the
lamp stops ashing, then take
the vehicle to your dealer/retailer as
soon as possible. SeeMalfunction
Indicator Lamp on page 4-18
for more information.
:Check Oil
This message is displayed if the oil
pressure or oil level is low. Stop
when safe, turn off the engine and
check the engine oil level. See
Engine Oil on page 9-8. Do not run
the engine when this warning is
4-28 Instruments and Controls
2008 - Pontiac G8 Owner Manual

illuminated. If the oil level is normal,
have the system checked at your
dealer/retailer.
You can press
3or8to
acknowledge that you received the
message, but
:Check Oil will
continue to appear in the bottom of
the DIC display until the vehicle
has been serviced.
X Contact Dealer
This message is displayed when
there is a fault in the instrument
panel, see your dealer/retailer.
You can press
3or8to
acknowledge that you received
the message, butXService will
continue to appear in the bottom of
the DIC display until the vehicle
has been serviced.
ICruise On, Cruise Off,
Cruise Active, and Cruise
Inactive
These messages display the status
of the cruise control system. See
Cruise Control on page 4-5for more
information.
Engine Immobilized Refer to
Owners Manual
This message is displayed when the
engine has been shutdown due to
the theft-deterrent system. See
Immobilizer Operation on page 2-12
for more information.
You can press
3or8to
acknowledge that you received the
message, but
AEng Immo will
continue to appear in the bottom of
the DIC display until the vehicle
has been serviced.
BEngine Temp
(Temperature) Hot
This message is displayed when the
engine coolant temperature is
excessively hot. Stop the vehicle as
soon as it is safe to do so. See
Engine Overheating on page 9-16.
You can press
3or8to
acknowledge that you received the
message, but
BTemp Hot will
continue to appear in the bottom of
the DIC display until the vehicle
has been serviced.
.Low Fuel
This message is displayed when the
fuel level is low.
You can press
3or8to
acknowledge that you received the
message, but
.Low Fuel will
continue to appear in the bottom
of the DIC display until the fuel
tank has been lled above the low
fuel level.
Instruments and Controls 4-29
2008 - Pontiac G8 Owner Manual

yOverSpeed
This message is displayed when the
vehicle’s speed is greater than
the set OverSpeed value. See
“OverSpeed” underDIC Operation
and Displays on page 4-23.
You can press
8or move the
thumbwheel up
Qor downRto
acknowledge that you received
the message, but OverSpeed will
continue to appear in the bottom of
the DIC display as long as the
vehicle’s speed exceeds the preset
value.
$Park Brake
This message is displayed if the
parking brake is applied when you
are driving. Release the parking
brake. SeeParking Brake on
page 8-9.
Replace Battery in
Remote Key
This message is displayed when the
battery in the remote keyless
entry transmitter needs to be
replaced. See your dealer/retailer to
replace the battery.
You can press
3or8to
acknowledge that you received the
message, but
QKey Batt will
continue to appear in the bottom of
the DIC display until the battery
has been replaced.
wRest Reminder
This feature reminds the driver that
they may have been driving for too
long without a break. When the
ignition is turned on, a timer starts
counting. After two hours of
continuous driving, the rest reminder
ashes to alert the driver. The Rest
Reminder message is displayed until
3or8are pressed. The rest
reminder reappears after 20 minutesaccompanied by a chime, unless the
ignition has been turned off. For
information on how to turn the rest
reminder on and off, seeDIC Vehicle
Customization on page 4-32.
{Safety Mode Active and
Power Reduced
These messages display alternately
when there is a problem with the
engine control system, see
your dealer/retailer.
You can press
3or8to
acknowledge that you received the
message, but
{Safety will
continue to appear in the bottom of
the DIC display until the vehicle
has been serviced.
4-30 Instruments and Controls
2008 - Pontiac G8 Owner Manual