2007 HUMMER H2 Owners Manual

To return the seat(s) to the upright position, do the
following:
1. Lift the seatback up and push it rearward all
the way.
2. Lower the seat cushion until it latches into
position.
3. Pull forward on the seatback and up on
the seat cushion to make sure the seat is
securely in place.
4. Return the head restraints (SUV only) to the
upright position.
Third Row Seat (SUV)
Entering or Exiting the Third Row Seat
If your vehicle has a third row seat, you must
fold the second row seat down before entering or
exiting the third row. See “Folding the Seatbacks”
under60/40 Split Bench Seat on page 15
earlier in this section for instructions.
The third row seatback can be folded and the
entire seat can be tilted or removed from
the vehicle.
Folding the Seatback
To fold the seatback, do the following:
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
1. Pull up on the
release lever
labeled 1, located on
the rear of the
seatback, and push
the seatback
forward.
17

Unfolding the Seatback
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
To return the seatback to the passenger position,
do the following:
1. Pull up on the
release lever
labeled 1 and then
pull up on the
seatback until the
seatback locks
into the upright
position.
2. Push forward on the seatback to make sure it
is locked into position.
Tilting the Seat
1. Fold the seatback forward using the
instructions listed previously.
2. Unlatch the seat
from the oor by
pulling up on
the lever labeled 2,
located on the
rear of the seat.
3. Lift the rear of the seat up from the oor and
push it forward until it locks into place. You
will not be able to unlatch the seat from
the oor unless the seatback is folded down.
The seat will now remain locked in the upright
position.
18

Returning the Seat from a Tilted to an
Upright Position
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.To return the seatback to an upright position, do
the following:
1. Pull the lever labeled 3 toward you.
2. While still holding lever 3 toward you, grasp
the top of the seat and pull it toward you
slightly.
19

3. Let go of lever 3 and pull the seat
completely down.
4. Push down on the seat rmly. Try pulling it up
to be sure it is locked into place.
5. Pull up on the
release lever
labeled 1 and then
pull up on the
seatback until the
seatback locks into
the upright position.Removing the Seat
To remove the seat, do the following:
1. Open the liftgate.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
2. Fold the seatback
forward onto the
seat cushion
by using the lever
labeled 1. The
seat cannot
be removed unless
the seatback is
folded.
20

3. To unlatch the rear
of the seat from the
oor, pull up on the
release lever
labeled 2, at the rear
of the seat, and lift
the rear of the seat
up from the oor.
4. Squeeze the release handle while pulling the
seat out of the slots on the oor.
5. While holding the rear of the seat up, roll the
seat out of the vehicle.
21

Installing the Seat
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on
the seatback to be sure it is locked.
{CAUTION:
A seat that is not locked into place
properly can move around in a collision or
sudden stop. People in the vehicle could
be injured. Be sure to lock the seat into
place properly when installing it.
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not
provide the protection needed in a crash.
The person wearing the belt could be
seriously injured. After raising the rear
seatback, always check to be sure that the
safety belts are properly routed and
attached, and are not twisted.
22

To install the seat, do the following:
1. While holding the rear of the seat up, slide the
front wheels into the slots on the oor. The
front latches should lock into place. If the
latches do not lock, try tilting the rear of the
seat upward.
2. Once the latches are engaged, pull up on
the lever labeled 3 to allow the seat to drop
into place.3. Pull up on the lever labeled 1 to return the
seatback to its upright position.
4. Push and pull on the seat to make sure it is
locked into place. The seatback cannot be
raised to the upright position unless the seat is
secured to the oor.
23

Safety Belts
Safety Belts: They Are for Everyone
This part of the manual tells you how to use
safety belts properly. It also tells you some things
you should not do with safety belts.
{CAUTION:
Do not let anyone ride where he or she
cannot wear a safety belt properly. If you
are in a crash and you are not wearing a
safety belt, your injuries can be much
worse. You can hit things inside the
vehicle or be ejected from it. You can be
seriously injured or killed. In the same
crash, you might not be, if you are
buckled up. Always fasten your safety
belt, and check that your passengers’
belts are fastened properly too.
{CAUTION:
It is extremely dangerous to ride in a
cargo area, inside or outside of a vehicle.
In a collision, people riding in these areas
are more likely to be seriously injured or
killed. Do not allow people to ride in any
area of your vehicle that is not equipped
with seats and safety belts. Be sure
everyone in your vehicle is in a seat and
using a safety belt properly.
Your vehicle has a light
that comes on as a
reminder to buckle up.
SeeSafety Belt
Reminder Light on
page 206.
24