2007 HUMMER H2 Owners Manual

3. Pull off the license plate holder from the
spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts. Turn the
wheel wrench with the wheel wrench
extender counterclockwise to loosen the
wheel nuts.5. Remove the three wheel nuts holding the
spare tire onto the tire carrier.
6. Pull off the spare tire and gently lower it to the
ground. Set it next to the at tire.
473

Removing the Spare Tire and
Tools (SUT)
The jack is stored in the rear cargo compartment
on the passenger’s side of the vehicle. The
tools for the jack are stored under the rear
passenger’s seat.
To remove the tools, do the following:
1. Locate the tools by lifting the driver’s side
second row seat up to expose the oor.
See60/40 Split Bench Seat on page 15for
more information.
2. Remove the strap from the seat rail. Then
carefully slide the tool bag out from under
the seat rail as shown.
Take care to not pinch the seat cables or
electrical harnesses.
474

3. Open the tool bag. You will nd the following
tools needed to remove the spare tire and
at tire:
A. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel BlocksTo access the jack, rst remove the tonneau cover
on the rear cargo compartment. SeeTonneau
Cover (SUT) on page 167for more information.
To remove the cover, unlock it and then pull
the cover off.
475

Release the jack by inserting the wheel wrench (A)
into the hole (B) and turn counterclockwise.
Before proceeding, be sure to set the wheel blocks
at the appropriate tires as previously shown.
Remove the wheel
blocks from the tool
bag. Then lift the wheel
block as shown to
lock it into place.
Removing the Spare Tire (SUT)
The spare tire is attached to the tire carrier.
To remove the spare tire, do the following:
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 108for tire carrier operation.
2. Unscrew the wing nut on the back of the
tire carrier.
476

3. Pull off the license plate holder from the
spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.
5. Turn the wheel wrench with the wheel wrench
extender counterclockwise to loosen the
wheel nuts.6. Remove the three wheel nuts holding the
spare tire onto the tire carrier.
7. Pull off the spare tire and gently lower to the
ground. Set it next to the at tire.
477

Removing the Flat Tire and
Installing the Spare Tire
Jack (SUV and SUT)
1. To remove the
center cap, place
the at end of
the wheel wrench in
the slot on the
wheel and carefully
pry the center
cap out.
2. Attach the wheel wrench to the extender.3. Turn the wheel wrench counterclockwise to
loosen the wheel nuts. Do not remove
them yet.
You will now need to jack the vehicle up using
the following instructions.
478

4. Assemble the jack and tools as follows:
Front Flat Tire:Attach the jack handle with
the hook end connected to the hole on
the jack. Slide the wheel wrench onto the jack
handle extension.Rear Flat Tire:Assemble the jack together
with the jack handle and the jack handle
extensions.
5. Turn the wheel wrench clockwise to raise the
jack head to the lifting point.
479

6.Front Flat Tire:Position the jack under the
vehicle on the front lower control arm behind
the at tire.Rear Flat Tire:Place the jack under the
curved rear axle pad. Make sure the jack head
is positioned so that the rear axle pad is
resting securely on the jack head.
{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack you could be badly injured or
killed. Never get under a vehicle when it is
supported only by a jack.
Front Flat Tire – JackRear Flat Tire – Jack
480