2007 HUMMER H2 Owners Manual

Power Lumbar
Your vehicle’s seats have power lumbar.
You can increase or
decrease lumbar
support in an area of
the lower seatback with
this control, located
on the outboard sides of
the front seat(s).
To increase support, press and hold the front of
the control. To decrease support, press and
hold the rear of the control. Let go of the control
when the lower seatback reaches the desired level
of support.You can also reshape the side wing area of the
lower seatback for more lateral support.
To increase support, press and hold the top of the
control. To decrease support, press and hold
the bottom of the control. Let go of the control
when the lower seatback reaches the desired level
of support.
Your vehicle may have a memory function which
allows seat settings to be saved and recalled.
SeeMemory Seat and Mirrors on page 10for more
information.
9

Heated Seats
If your vehicle has this
feature, the buttons are
located on the front
doors. The engine must
be running for the
heated seats to work.
To heat the entire seat, press the horizontal button
with the heated seat and seatback symbol.
Press the button to cycle through the temperature
settings of high, medium and low and to turn
the heated seat off. Indicator lights will come on to
designate the level of heat selected: three for
high, two for medium, and one for low.
To heat only the seatback, press the vertical button
with the heated seatback symbol. An indicator light
on the seatback button will come on to designate
that only the seatback is being heated.Additional presses of the seatback button will cycle
through the heat levels for the seatback only. Press
the horizontal button again to heat the whole seat.
The heated seats will be canceled after the ignition
is turned off. If you still want to use the heated seat
feature after you restart your vehicle, you will need
to press the heated seat button again.
Memory Seat and Mirrors
If your vehicle has this
feature, the controls for
the memory function
are located on the
driver’s door.
These buttons are used to program and recall
memory settings for the driver’s seat and both the
driver’s and passenger’s outside mirrors. The
settings for these features can be saved for up to
two drivers.
10

To store the memory settings, do the following:
1. While the vehicle is in PARK (P), adjust
the driver’s seat, including the seatback
recliner, lumbar, and side wing area, and
both outside mirrors to your preference.
2. Press and hold the 1 or 2 button of the memory
control for three seconds. A double chime will
sound to let you know that the position has
been stored.
To repeat the procedure for a second driver,
follow the preceding steps, but press the other
numbered memory control button.
Each time button 1 or 2 is pressed and released
while the vehicle is in PARK (P), a single chime will
sound and the memory position will be recalled.
To stop recall movement of the memory seat
feature at any time, press one of the memory
buttons or power seat controls.Easy Exit Seat
The controls for this memory function are located
on the driver’s door.
B(Easy Exit Seat):This button is used to
program and recall the desired driver’s seat
position when exiting or entering the vehicle. The
seat position can be saved for up to two drivers.
To store the seat exit position, do the following:
1. Press and release the 1 or 2 button. The seat
will move to the stored memory position.
2. Adjust the seat to the desired exit position.
3. Press and hold the exit button of the memory
control for three seconds. A double chime will
sound to let you know that the position has
been stored for the selected button 1 or 2.
To repeat the procedure for a second driver,
follow the preceding steps, but press the
other numbered memory control button.
11

To use the seat exit position, do one of the
following:
Press the exit button on the memory control,
or
If this feature is activated in the DIC, removing
the key from the ignition will move the seat to
the exit position.
See “Easy Exit Seat” underDIC Vehicle
Customization on page 234for more information
on activating this feature in the DIC.
Power Reclining Seatbacks
The front seats have power reclining seatbacks.
The control used to operate the seatbacks
are located on the outboard side of the seats.
To recline the seatback, press the control
toward the rear of the vehicle.
To raise the seatback, press the control
toward the front of the vehicle.
12

{CAUTION:
Sitting in a reclined position when your
vehicle is in motion can be dangerous.
Even if you buckle up, your safety belts
cannot do their job when you are reclined
like this.
The shoulder belt cannot do its job. In a
crash, you could go into it, receiving neck
or other injuries.
The lap belt cannot do its job either. In a
crash the belt could go up over your
abdomen. The belt forces would be there,
not at your pelvic bones. This could cause
serious internal injuries.
For proper protection when the vehicle is
in motion, have the seatback upright.
Then sit well back in the seat and wear
your safety belt properly.
Do not have a seatback reclined if your vehicle is
moving.
13

Head Restraints
Adjust the head restraint so that the top of the
restraint is at the same height as the top of
the occupant’s head. This position reduces the
chance of a neck injury in a crash.Pull the head restraint up to raise it. Push the
head restraint down to lower it.
Each front head restraint can also be tilted forward
to four positions by pulling on it. A click will
sound after each tilt position is reached. Pull the
head restraint forward, past the last position,
to release it to the upright position.
The rear seat head restraints are also adjustable
up and down, but they do not tilt.
14

Rear Seats
Heated Seats
If your vehicle has this
feature, the buttons
used to control
this feature are located
on the back of the
center console.
The engine must be
running for the heated
seat feature to work.
To heat the seat cushion, press the button to
cycle through the temperature settings of high and
low. Press the button a third time to turn the
feature off. An indicator light will glow for each heat
setting when the feature is operating.
The heated rear seats will shut off automatically
when the ignition is turned off.
60/40 Split Bench Seat
The 60/40 split bench seats can be folded to give
you more cargo space.
Folding the Seatbacks
The seatbacks are equipped with rearward folding
head restraints (SUV only). When the seatback
is being folded down, the head restraint will
automatically fold rearward.
To fold the rear seat, do the following:
1. Make sure that nothing is under or in front of
the seat.
2. Pull up on the strap
loop located at the
rear of the seat
cushion and pull the
seat cushion up
and fold it forward.
15

Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
3. Pull the seatback forward and fold it down until
it is at.
If the seatback cannot fold at because it
interferes with the cushion, try moving the front
seat forward and/or bringing the front
seatback more upright.
4. Repeat the steps for the other half of the
60/40 split bench seat.Returning the Seats to an Upright
Position
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not
provide the protection needed in a crash.
The person wearing the belt could be
seriously injured. After raising the rear
seatback, always check to be sure that the
safety belts are properly routed and
attached, and are not twisted.
16