2006 LAND ROVER FRELANDER 2 wheel

DT C
Description Possible Cause Action
modul e (TCM) fault General Procedures ).
Cal ibrat e t he gear pos it ion sens or us i ng the
approved di agnos ti c s ys t em. Refer to the
warrant y poli cy and procedures manual if t he
TCM is sus pect .
P0709-00
Trans mis s ion range sens or
A circui t int ermi tt ent Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0711-00
Trans mis s ion flui d
temperature s ens or A
circuit range/performance Transmis si on fluid
temperat ure s ens or ci rcuit :
hi gh res is t ance i n t ermi nal s Transmis si on fluid
temperat ure s ens or fault Check t he transmis s ion fluid temperat ure
sens or and ci rcuit s. Refer to t he elect rical
gui des . Recti fy as necess ary.
P0712-00 Trans mis s ion flui d
temperature s ens or A
circuit l ow Transmis si on fluid
temperat ure s ens or ci rcuit :
short ci rcuit t o ground Transmis si on fluid
temperat ure s ens or ci rcuit :
open circui t P0713-00
Trans mis s ion flui d
temperature s ens or A
circuit hi gh Transmis si on fluid
temperat ure s ens or ci rcuit :
short ci rcuit t o power P0715-00
Turbine/Input shaft speed
(ISS) s ens or A circui t Transmis si on ISS ci rcuit :
short ci rcuit t o power Check t he transmis s ion ISS s ens or and circuit s .
Refer to the el ect ri cal guides . Ins tal l a new ISS
sens or as neces sary. For addit ional i nformati on,
refer t o: (307-01 Aut omati c
Transmis s ion/Trans axle)
Input Shaft Speed (ISS) Sensor - I6 3.2L Pet rol (Removal and Ins t al lat ion),
Input Shaft Speed (ISS) Sensor - TD4 2.2L Di esel (Removal and Ins t allat ion).
P0716-00
Turbine/Input shaft speed
(ISS) s ens or A circui t
range/performance Transmis si on ISS s ens or
ci rcuit : high res i st ance in
terminals Transmis si on ISS s ens or fault
P0718-00
Turbine/input shaft speed
(ISS) s ens or A circui t
int ermi tt ent Transmis si on ISS s ens or
ci rcuit : int ermi tt ent hi gh
res is tance in terminals Transmis si on ISS s ens or fault
P0720-00
Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit ) OSS s ens or ci rcuit : s hort
ci rcuit t o power Check t he transmis s ion OSS s ens or and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
P0721-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit )
range/performance The wheel radi us does not
agree wit h t he wheel radius
programmed in t he car
confi gurati on fi le OSS s ens or not ins tall ed
correctl y OSS s ens or ci rcuit : high
res is tance in terminals OSS s ens or fault Check t hat t he correct wheels and ti res are
ins tall ed. Check t he transmis si on OSS s ensor
for correct ins t al lat ion. Check t he OSS s ensor
and ci rcuit s. Refer to t he elect rical guides.
Rect ify as neces s ary.
P0722-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit ) no
s ignal OSS s ens or ci rcuit : high
res is tance in terminals OSS s ens or ci rcuit : open
ci rcuit OSS s ens or ci rcuit : s hort
ci rcuit t o ground OSS s ens or fault
Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he transmis s ion OSS s ens or and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if t he TCM is s us pect.
P0723-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit )
int ermi tt ent OSS s ens or not ins tall ed
correctl y OSS s ens or ci rcuit :
intermit t ent hi gh res is t ance
in t ermi nals OSS s ens or fault
Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he transmis s ion OSS s ens or for correct
ins tall ati on. Check the OSS s ens or and circuit s .
Refer to the el ect ri cal guides . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if t he TCM is s us pect.
P0725-00 Engi ne s peed input ci rcuit Cont roll er area network
(CAN) circui t: open circui t CAN circuit : s hort circui t to
ground CAN module fault Carry out a compl ete vehicle read for CAN
relat ed DTCs. Recti fy as neces sary.
P0729-00 Gear 6 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and Carry out a compl ete read for related engi ne
torque DTCs . Check trans mi ss i on fl uid l evel and
condit ion. Refer t o the warrant y poli cy and
procedures manual if t he t rans mis s ion i s
sus pect .

Publi s hed: 29-Nov-2011
Identification Codes - Identification Codes
Des cript ion and Operat ion
VIN Number
VIN and identi fi cat ion l abel l ocat ions:
1. The VIN is st amped on a pl ate t hat is vi si ble t hrough t he lowes t part of t he left si de of the windshi el d.2.UK, Europe and ROW The VIN l abel i s located at t he bott om of t he l eft-hand front door 'B' Pil lar.3.UK, Europe and ROW The Ti re Dat a/Specifi cat ion label i s att ached to t he right-hand B-pi llar.4.China Market s peci fic VIN label at bot tom of ri ght -hand 'B' Pi llar (RH s ide for China)5.USA and Canada Vin included on market s peci fi c tyre label including cert ificati on compliance s tat ement ondri ver's s i de 'B' Pill ar bel ow door st riker.6. The VIN is st amped in the body just forward of the spare wheel wel l.
W i nds creen VIN
VIN label - UK, Europe and ROW
ItemPart NumberDescription
1-Type/Approval Number - If s hown2-VIN Number
3-Gros s Vehicle W eight
4-Gros s Trai ler W eight5-Front Axl e W ei ght
6-Rear Axle W eight

Publ is hed: 24-Jun-2011
Jacking and Lifting - Jacking
Des cript ion and Operat ion
General
W ARNING: The foll owing i nst ructi ons mus t be adhered to before rais i ng the vehicle off t he ground:
Posi ti on vehi cl e on a sol id, level surface.Apply t he parking brake.Select 'P' - PARK on automat ic t rans mis s ion sel ect or.Select 'N' - Neutral on manual t rans mis s ion.
W ARNING: If t he dri ve s haft(s ) are t o be di sconnect ed, i t wil l be neces s ary t o rai s e all four wheels off the ground inorder t hat t he s haft (s ) can be rot ated. DO NOT us e the cus tomer jack and ens ure that t he vehi cl e is adequatel y s upport edon axle s t ands . W i th the vehicle rai sed, it will be necess ary to releas e t he park brake and sel ect Neutral - 'N' in the mai nt ransmis s ion t o enabl e t he dri ve s haft(s ) to be rot ated.
• CAUTIO NS:
To avoid damage t o t he underbody components of t he vehi cle, the foll owing i ns t ructions mus t be adhered to:
Do not pos it ion jacks or axle s t ands under the foll owing component s :
Body s truct ure ot her t han any approved jacki ng or li ft ing point sRear subframeBumpersFuel l inesFuel t ankBrake l inesFront or rear s uspens ion armsSteering l inkageRear di fferenti al uni tTrans mis s ionEngi ne oil pan - See not e below
• NOTE: For certain repair operat ions, i t may be necess ary to support t he engine under t he oil pan. In thi s cas e, a bl ock ofhardwood or a rubber pad mus t be pos it ioned on t he jack li ft ing pad t o protect the oi l pan.
Hydraulic jack
• W ARNINGS:
Before commenci ng work on undersi de of vehi cl e, ens ure that axle s t ands are correctly pos it ioned and vehi cle i ss ecurel y s upported.
Al ways chock the rear wheel s when jacking t he front of the vehicle.
A hydrauli c jack wi th a mi ni mum li ft ing capacit y of 1500 kg, (3,300 l bs) must be us ed.
Raising and Supporting the Vehicle
To as si s t in rais ing the vehicle, us e t he cus t omer jacki ng poi nts on the s i ll or on t he trolley jack pos i ti on at the rear of t hefront subframe as indicated i n t he fol lowing ill ust rat ions .
Raising the front of the vehicle
W ARNING: Always chock t he rear wheels when jacki ng the front of t he vehi cl e.
Apply t he parking brake.
Select 'P' - Park on aut omat ic trans mi s si on s el ect or.
Select 'N' - Neutral on manual t rans mis s ion.

Posi ti on li ft ing pad of jack beneath the jacki ng poi nt locat ed on t he rear of t he front subframe, posi ti on 3.
W i th vehi cl e at desi red height , carefull y lower jack unt il vehi cl e rest s on axle st and(s ), pos it ion 1 or 2.
W ARNING: Before commencing work on unders ide of vehicle, ensure t hat axle s tands are correctl y pos i ti oned andvehi cl e i s s ecurel y s upported.
CAUTION: Pos it ion s uit abl e mat eri al bet ween axl e s tands and t he s ill t o prevent damage.
Revers e procedure when removi ng vehi cl e from st ands.
Raising the rear of the vehicle
All vehicles
W ARNING: Always chock t he front wheel s when jacking t he rear of t he vehi cl e.
Apply t he parking brake.
Select 'P' - Park on aut omat ic trans mi s si on s el ect or.
Select 'N' - Neutral on manual t rans mis s ion.

Vehicles wi th four-wheel drive
On vehicles wi th four-wheel drive, posi ti on li ft ing pad of jack beneath the rear jacki ng poi nt located on t he rear di fferenti als upport bracket , pos it ion 3.
W i th vehi cl e at desi red height , pos i ti on axl e s tand(s ) as i ll us t rat ion and careful ly lower jack unti l vehicle res ts on axl es tand(s ), pos i ti on 1 or 2.
Vehicles wi th two-wheel dri ve
CAUTION: W it h no cent ral jacking poi nt at t he rear i t is not pos si ble t o rais e both s ides of the vehicle at once.
On vehicles wi th two-wheel drive, pos i ti on li ft ing pad of jack beneat h t he rear jacking poi nt locat ed on t he body, pos it ion1.
W i th vehi cl e at desi red height , pos i ti on axl e s tand(s ) as i ll us t rat ion and careful ly lower jack unti l vehicle res ts on axl es tand(s ), pos i ti on 2.
All vehicles
W ARNING: Before commencing work on unders ide of vehicle, ensure t hat axle s tands are correctl y pos i ti oned andvehi cl e i s s ecurel y s upported.
CAUTION: Pos it ion s uit abl e mat eri al bet ween axl e s tands and body to prevent damage.
Revers e procedure when removi ng vehi cl e from st ands.

Publi s hed: 11-May-2011
Jacking and Lifting - Lifting
Des cript ion and Operat ion
Two-Post Lift
W ARNING: Make sure t hat t he vehicle i s s table before commencing work.
CAUTION: If the drive s haft (s ) are to be removed, rel eas e t he parking brake and s el ect NEUTRAL 'N' i n t het ransmis s ion i n order t hat t he s haft (s ) can be rot ated when the vehicle is rais ed to the des ired height.
1. Pos i ti on the vehicle wit h t he cent re of the l ift pill ars al igned approxi mat el y wi th t he front of the driver/pass enger s eatcus hions .
ItemPart NumberDescription
1-Two post l ift locati ons - Cus t omer jacki ng points2-Opti onal, Two-pos t front li ft l ocat ions - Body mounti ng us ed in vehicle product ion
2. Ext end t he li ft ing arms and pos it ion t he pad of each l ifti ng arm beneat h t he approved poi nt s .
3. Rais e t he vehi cl e unti l the wheels are just cl ear of t he ground and check t hat the pads of each lift ing arm are s ti llcorrect ly pos it ioned.
4. Rais e t he vehi cl e t o t he des i red height .
5. Ensure t he vehi cl e is correctl y s upport ed wi th the l ifti ng pads in full cont act with t he approved poi nt s .
Vehicle on wheels - Four-Post Ramp
• W ARNINGS:
If the drive s haft (s ) are t o be dis connected, it will be necess ary to rais e al l four wheel s off t he ramp in order thatt he shaft(s ) can be rot at ed. Refer to the 'W heel Free Lift - Four-Pos t Ramp' s ecti on below for li ft ing i ns t ructi ons thenrel eas e t he parki ng brake and s elect NEUTRAL i n t he transmis si on.
Do not pus h t he vehi cl e backwards and forwards along t he ramp in order to gai n acces s t o the drive s haft fixi ngs .
Posi ti on t he vehi cl e on t he ramp wit h t he front and rear wheel s equidis t ant from t he ends of t he ramp. Chock t he wheel s,s elect NEUTRAL i n t he transmis si on and where pract ical, apply the parki ng brake.
Wheel-Free Lift - Four-Post Ramp

• NOTE: To enable t he vehi cle t o be s upport ed correctl y on t he wheel -free longit udi nal s, i t wil l be neces s ary t o produce 2off each of the support blocks t o the di mens ions given in the accompanying ill ust rations . The s upport ing part of each bl ockmus t be manufactured from s uit able hardwood or met al and the 'U' shaped bas e of each bl ock mus t be manufact ured frommet al . Note that it i s es sent ial to ens ure that t he 'U' s haped bas e of each block is wide enough to fit over t he wheel freelongit udinals .
Front s upport bl ock di mens ions
ItemPart NumberDescriptionA-130 mm (5.118 in)
B-160 mm (6.299 in)
C-90 mm (3.543 in)Rear support block dimens i ons
ItemPart NumberDescription
A-50 mm (1.1968 in)B-190 (7.480 in)
C-110 (4.330 in)
Rais ing and Support ing t he Vehicle
1. Posi ti on vehi cl e on ramp.
2. Appl y parking brake.
3. Rais e ramp t o required height
4. Ali gn the wheel -free l ongi tudinals and pos it ion the s upport blocks beneat h the pos it ions s hown

Engage wheel-free and l ower ramp unt il weight of vehi cl e res t s on s upport blocks and road wheels are jus t clear of ramp.
Ensure t hat vehicle is correct ly support ed on all four s upport blocks, t hat bl ocks are s ti ll correct ly pos it ioned and are in fullcont act wit h the body mount ing point s .
W ARNING: Make sure t hat t he vehicle i s s table before commencing work