Page 935 of 5267

3.(K25) BATTERY TEMP SENSOR SIGNAL
With the scan tool, read the Battery Temp Sensor voltage with the Batt Temp Sensor still disconnected.
Is the voltage above 4.6 volts?
Ye s>>
Go To 4
No>>
Go To 7
4.BATTERY TEMPERATURE SENSOR
Connect a jumper wire between the (K25) Battery Temp Signal circuit and the(K900) Sensor ground circuit at the
Sensor harness connector.
With the scan tool, read the Battery Temp Sensor voltage.
Is the voltage below 1.0 volt?
Ye s>>
Replace the Battery Temperature Sensor.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No>>
Go To 5
NOTE: Remove the jumper wire before continuing.
5.RESISTANCE IN THE (K25) BATTERY TEMP SENSOR SIGNAL CIRCUIT
Turn the ignition off.
Connect the Battery Temp Sensor harness connector.
NOTE: Make sure the voltmeter leads meet the terminals in the
connector and that there is good terminal to wire connection.
NOTE: Make sure the voltmeter leads are connected for positive
polarity
Backprobe the (K25) Battery Temp Sensor Signal circuit at the Sensor
harness connector and the PCM harness connector with both voltmeter
leads.
Start the engine.
Allow the engine to idle.
Is the voltage below 0.10 of a volt?
Ye s>>
Go To 6
No>>
Repair the excessive resistance in the (K25) Battery Temp
Sensor Signal circuit.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9 -
ENGINE - STANDARD PROCEDURE)
Page 936 of 5267

6.RESISTANCE IN THE (K900) SENSOR GROUND CIRCUIT
Turn the ignition off.
NOTE: Make sure the voltmeter leads meet the terminals in the
connector and that there is good terminal to wire connection.
NOTE: Make sure the voltmeter leads are connected for positive
polarity
Backprobe the (K900) Sensor ground circuit at the Battery Temperature
Sensor harness connector and the PCM harness connector using both
volt meter leads.
Start the engine.
Allow the engine to idle.
Is the voltage below 0.10 of a volt?
Ye s>>
Go To 8
No>>
Repair the excessive resistance in the (K900) Sensor
ground circuit.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9 -
ENGINE - STANDARD PROCEDURE)
7.(K25) BATTERY TEMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
Turn the ignition off.
Disconnect the Battery Temp Sensor harness connector.
Disconnect the PCM harness connectors.
Measure the resistance between ground and the (K25) Battery Temp
Signal circuit.
Istheresistancebelow100ohms?
Ye s>>
Repair the short to ground in the (K25) Battery Temp Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9 -
ENGINE - STANDARD PROCEDURE)
No>>
Go To 8
Page 938 of 5267
P0107-MAP SENSOR VOLTAGE TOO LOW
For a complete wiring diagramRefer to Section 8W.
Page 939 of 5267

When Monitored:
With the engine RPM above 416 but less than 1500, the TPS voltage less than 1.13 volts, and battery voltage
greater than 10.4 volts.
Set Condition:
The MAP Sensor signal voltage is below 0.1 of a volt for 2.0 seconds with the engine running.
Possible Causes
(F855) 5-VOLT SUPPLY CIRCUIT OPEN
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
(K1) MAP SIGNAL CIRCUIT SHORTED TO GROUND
(K1) MAP SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
MAP SENSOR
PCM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).
Diagnostic Test
1.MAP SENSOR VOLTAGE BELOW 0.08 OF A VOLT
Ignition on, engine not running.
With a scan tool, read the MAP Sensor voltage.
Is the voltage below 0.08 of a volt?
Ye s>>
Go To 2
No>>
Refer to the INTERMITTENT CONDITION Diagnostic Procedure. (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
2.(F855) 5-VOLT SUPPLY CIRCUIT
Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F855) 5-volt Supply circuit in the MAP Sen-
sor harness connector.
Is the voltage between 4.5 to 5.2 volts?
Ye s>>
Go To 3
No>>
Go To 6
Page 940 of 5267

3.MAP SENSOR
With a scan tool, monitor the MAP Sensor voltage with the Sensor harness connector disconnected.
Is the voltage above 4.5 volts?
Ye s>>
Replace the MAP Sensor.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No>>
Go To 4
4.(K1) MAP SIGNAL CIRCUIT SHORTED TO GROUND
Turn the ignition off.
Disconnect the C1 PCM harness connector.
Measure the resistance between ground and the (K1) MAP Signal cir-
cuit in the MAP Sensor harness connector.
Istheresistancebelow100ohms?
Ye s>>
Repair the short to ground in the (K1) MAP Signal circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No>>
Go To 5
5.(K1) MAP SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
Measure the resistance between the (K1) MAP Signal circuit and the
(K900) Sensor ground circuit in the MAP Sensor harness connector.
Istheresistancebelow100ohms?
Ye s>>
Repair the short between the (K900) Sensor ground and the
(K1) MAP Signal circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No>>
Go To 8
Page 941 of 5267
6.(F855) 5-VOLT SUPPLY CIRCUIT OPEN
Turn the ignition off.
Disconnect the C1 PCM harness connector.
Measure the resistance of the (F855) 5-volt Supply circuit from the MAP
Sensor harness connector to the PCM harness connector.
Is the resistance below 5.0 ohms?
Ye s>>
Go To 7
No>>
Repair the open in the (F855) 5-volt Supply circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
7.(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
Measure the resistance between ground and the (F855) 5-volt Supply
circuit in the MAP Sensor harness connector.
Istheresistancebelow100ohms?
Ye s>>
Repair the short to ground in the (F855) 5-volt Supply cir-
cuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No>>
Go To 8
Page 943 of 5267
P0108–MAP SENSOR VOLTAGE TOO HIGH
For a complete wiring diagramRefer to Section 8W.
Page 944 of 5267

When Monitored:
With the engine RPM above 400, the TPS voltage less than 1.13 volts, and battery voltage greater than 10.4
volts
Set Condition:
With the engine RPM above 400, the TPS voltage less than 1.13 volts, and battery voltage greater than 10.4
volts
Possible Causes
(K1) MAP SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K1) MAP SIGNAL CIRCUIT OPEN
(K1) MAP SIGNAL CIRCUIT SHORTED TO THE (F856) 5-VOLT SUPPLY CIRCUIT
(K900) SENSOR GROUND CIRCUIT OPEN
MAP SENSOR
PCM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).
Diagnostic Test
1.MAP SENSOR VOLTAGE ABOVE 4.92 VOLTS
Start the engine.
With a scan tool, read the MAP Sensor voltage.
Is the voltage above 4.92 volts?
Ye s>>
Go To 2
No>>
Refer to the INTERMITTENT CONDITION Diagnostic Procedure. (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
2.MAP SENSOR
Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Connect a jumper wire between the (K1) MAP Signal circuit and the
(K900) Sensor ground circuit in the Sensor harness connector.
Ignition on, engine not running.
With a scan tool, monitor the MAP Sensor voltage.
Is the voltage below 1.0 volt with the jumper wire installed?
Ye s>>
Replace the MAP Sensor.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No>>
Go To 3
NOTE: Remove the jumper wire before continuing.