2006 ACURA CSX lock

Î
(#'


)
µ
µ
µ
µ
µ
µ µ
µ
Driver cannot select reverse gear when
vehicle speed is 15 km/h (9 mph) or less
YES
NO
YES
NO
YES
NO YES
NO
13-76Reverse Lockout System
Symptom Troubleshooting (cont’d)
REVERSE LOCKOUT SOLENOID 2P CONNECTOR
RVS (GRN/BLK)
NOTE: When checking if the transmission will shift to reverse while the wheels are being driven forward,
raise the vehicle on a lift, make sure it is securely
supported, and allow the front wheels to rotate freely.
 Do not release the clutch pedal if you can select reverse gear while the wheels are driven forward.
 When the vehicle is on a lift, and you make the wheels rotate, turn off the VSA system by the VSA
OFF switch.
1. Turn the ignition switch to LOCK (0).
2. Try to shift the transmission into reverse.
Go to step 4.
Go to step 3.
3. Do the reverse lockout solenoid test (see page 13-77).
Check the change lever assembly (see page
13-105), if necessary inspect the internal
transmission.
Repair or replace the reverse lockout solenoid
(see page 13-77).
4. Start the engine, and try to shift the transmission into reverse.
Intermittent failure, the system is OK at this
time.
Go to step 5. 5. Turn the ignition switch to LOCK (0).
6. Jump the SCS line with the HDS.
7. Disconnect ECM connector A (44P).
8. Disconnect the r
everse lockout solenoid 2P
connector.
9. Check for continuity between the reverse lockout solenoid 2P connector terminal No. 1 and body
ground.
Repair short to body ground in the wire
between the reverse lockout solenoid and the
ECM.
Check for loose terminals or poor connections
at the ECM. If necessary, update the ECM if it does
not have the latest software (see page 11-227), or
substitute a known-good ECM (see page 11-7), then
recheck. If the symptom goes away with a known-
good ECM, replace the original ECM (see page
11-228).
Wire side of female terminals
Can y ou shi f t t he t r ansmi ssi on i nt o t he r ev er se?
I s t he r ev er se l ock out sol enoi d OK ?
Can y ou shi f t t he t r ansmi ssi on i nt o t he r ev er se? Is there continuity?
08/08/21 14:46:40 61SNR030_130_0078
ProCarManuals.com
DYNOMITE -2009-


(#'



)
Î
(#'



")
13-7713-77
Reverse Lockout Solenoid Test Reverse Lockout Solenoid Disassembly/Reassembly
REVERSE LOCKOUT SOLENOID
2P CONNECTOR
A
1. Remove the reverse lockout solenoid (see page13-77).
2. Connect battery positive terminal to the r everse
lockout solenoid 2P connector No. 2 terminal, and
connect the battery negative terminal to the No. 1
terminal.
3. Make sure the reverse lockout solenoid works. If the reverse lockout solenoid does not work, replace
it. 1. Do the battery removal procedure (see page 22-69).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the battery base (see step 4 on page 13-84).
4. Disconnect the output shaft (countershaft) speed
sensor connector, the back-up light switch
connector, and the r everse lockout solenoid
connector (see step 6 on page 13-84).
5. Carefully remove the shift cables and the cable bracket together to avoid bending the cables (see
step 7 on page 13-85).
6. Remove the reverse lockout solenoid (A).
(cont’d)
Terminal side of male terminals
08/08/21 14:46:40 61SNR030_130_0079
ProCarManuals.com
DYNOMITE -2009-

Î
13-78Reverse Lockout System
Reverse Lockout Solenoid Disassembly/Reassembly (cont’d)
C
B
A
6x1.0mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
A
7. Remove the roller (A), the select lock return spring
(C), and select lock cam B.
8. Install the components of the r everse lockout
solenoid in the reverse order of removal.
9. Clean any dirt and oil from the mating surface of the reverse lockout solenoid and the change lever
assembly.
10. Apply liquid gasket, P/N 08718-0001 evenly to the change lever assembly mating surface of the
reverse lockout solenoid. Install the com ponent
within 5 minutes of applying the liquid gasket.
NOTE:  If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket. 11. Install the reverse lockout solenoid (A).
12. Install the cable bracket and the shift cables (see
step 37 on page 13-97).
13. Connect the r everse lockout solenoid connector,
the back-up light switch connector, and the output
shaft (countershaft) speed sensor connector (see
step 39 on page 13-97).
14. Install the battery base (see step 41 on page 13-98).
15. Install the air cleaner assembly (see page 11-345).
16. Do the battery installation procedure (see page 22-69).
08/08/21 14:46:40 61SNR030_130_0080
ProCarManuals.com
DYNOMITE -2009-

Ì
Ï



(#'

 )
Special Tools Required
13-84
Manual Transmission
Transmission Removal
A
B C
D
A A
B
D
C
A
B
 Engine hanger adapter VSB02C000015
 2006 Civic engine hanger VSB02C000025
 Engine support hanger, A and Reds AAR-T 1256
 Front subframe adapter VSB02C000016
These special tools are available through the Acura
Canada Technical Tools Department; FAX
866-398-8665/e-mail: ch_technicaltools ch.honda.com
NOTE: Use fender covers to avoid damaging painted
surfaces.
1. Do the battery removal procedure (see page 22-69).
2. Remove the cowl cover and the under-cowl panel (see page 20-163).
3. Remove the air cleaner assembly (see page 11-345).
4. Remove the harness clips (A) and the intake air duct (B), then remove the battery base (C) with the
coolant reservoir (D). 5. Remove the clutch line bracket (A), then carefully
move the slave cylinder (B) out of the way to avoid
bending the clutch line.
NOTE: Do not press the clutch pedal after the slave
cylinder has been moved.
6. Disconnect the back-up light switch connector (A), the output shaft (countershaft) speed sensor
connector (B), the r everse lockout solenoid
connector (C), and the harness clips (D).
08/08/21 14:47:19 61SNR030_130_0086
ProCarManuals.com
DYNOMITE -2009-




’06 model
’07-09 models
13-85
A
D
C
D
A
D
B C
D A
B
C A
A
7. Remove the cotter pins (A) or the lock pins (B), and the shift cable bracket (C), then disconnect the shift
cables (D) from the top of the change lever
assembly. Carefully remove both cables and the
bracket together to avoid bending the cables. 8. Remove the harness clips (A) from the clutch cable
bracket (B) and the harness bracket (C).
9. Remove the air cleaner housing bracket (A).
(cont’d)
08/08/21 14:47:20 61SNR030_130_0087
ProCarManuals.com
DYNOMITE -2009-

Î
Î


13-86Manual Transmission
Transmission Removal (cont’d)
A
B
C
VSB02C000015 VSB02C000025
A D
B
C
AAR-T1256
10. Remove the engine wire harness cover (A) by lifting up on the lock tab (B), then slide the harness
cover forward off the bracket (C).
11. Attach the engine hanger adapter (VSB02C000015) to the threaded holes in the cylinder head. 12. Install the front leg assembly (A), the hook (B), and
the wingnut (C) from an A and Reds engine support
hanger (AAR-T1256) onto the 2006 Civic engine
hanger (VSB02C000025). Carefully position the
engine hanger on the vehicle, and attach the hook
to the forward hole in the engine hanger adapter
(D). Tighten the wingnut by hand to lift and support
the engine/transmission assembly.
NOTE: Use care when working around the
windshield.
13. Remove the two upper transmission mounting bolts.
08/08/21 14:47:21 61SNR030_130_0088
ProCarManuals.com
DYNOMITE -2009-








13-87
A
B
B
B
A
B A
B
C D
B
14. Remove the under-hood fuse/relay box (A) by lifting up on the lock tabs (B), then move it aside.
15. Remove the engine control module (ECM) bracket (A), then move it aside. Remove the clutch line
clamp (B). 16. Disconnect the ground cable (A), then remove the
transmission mount bracket bolts (B) and nuts (C).
Remove the transmission mount bracket (D).
17. Raise the vehicle on a lift.
18. Remove the splash shield.
19. Drain the MTF. Reinstall the drain plug with a new sealing washer (see page 13-82).
20. Separate the lower arm (see step 5 on page 16-4).
(cont’d)
08/08/21 14:47:22 61SNR030_130_0089
ProCarManuals.com
DYNOMITE -2009-

ÎÎ

’06 model
’07-09 models
13-97
8x1.25mm
27 N·m (2.8 kgf·m, 20 lbf·ft)
C B
C
A
(P/N 08C30-B0234M) E
D
C
B
C
A
(P/N 08C30-B0234M) 8x1.25mm
27 N·m (2.8 kgf·m, 20 lbf·ft)
A
D
B C
37. Apply a light coat of silicone grease (P/N 08C30-
B0234M) to the shift cable ends (A).
NOTE: Make sure not to get any silicone grease on
the terminal part of the connectors and switches,
especially if you have silicone grease on your
hands or gloves
38. Install the shift cable bracket (B) and the shift cables(C), then install new cotter pins (D) or lock pins (E).
39. Connect the back-up light switch connector (A), the output shaft (countershaft) speed sensor connector
(B), and the reverse lockout solenoid connector (C).
Install the harness clips (D).
(cont’d)
Replace.
08/08/21 14:47:30 61SNR030_130_0099
ProCarManuals.com
DYNOMITE -2009-