2006 ACURA CSX oil

Î
(#'

")
13-105
Change Lever Assembly Disassembly/Reassembly
DUST COVEROIL SEAL
SHIFT ARM
COVER
SELECT STOP
PLATE DUST SEAL
INTERLOCK
5TH/6TH
SELECT
SPRING WASHER
REVERSE LOCKOUT
SOLENOID (MOLYBDENUM)
1ST/2ND
SELECT
SPRING
SELECT
LOCK CAM A
MBS RETURN
SPRING
CHANGE
LEVER COVER
SHIFT
ARM (MOLYBDENUM)
(MOLYBDENUM)
SELECT LEVER
SELECT
LOCK CAM B
ROLLER
CHANGE LEVER
6x1.0mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
8mm
SPRING
WASHER8mm
SPECIAL BOLT
31 N·m
(3.2 kgf·m,
23 lbf·ft)
MBS ARM
BREATHER CAP
NOTE:
 Do not install components if too much time has passed after applying liquid gasket. Instead, remove the old residue, and reapply liquid gasket.
 Prior to reassembling, clean all parts in solvent, dry them, and apply grease to the contact surfaces as shown.
Replace.
Replace.
Apply liquid gasket
(08C70-X0331S) to
the sealing surface. Be careful not to damage the dust seal
when installing it.
Turn toward the front of
the vehicle, and install it.
08/08/21 14:47:58 61SNR030_130_0107
ProCarManuals.com
DYNOMITE -2009-

µ
µ

 
Î
(#'

 )
Special Tools Required
13-129
Mainshaft Bearing and Oil Seal Replacement
C
07736-A01000B
A
B
D
A A
07749-0010000
B
07746-0010300
A
07JAD-PL90100
 Oil seal driver, 65 mm 07JAD-PL90100
 Adjustable bearing puller, 20 40 mm 07736-A01000B
 Bearing driver attachment, 42 x 47 mm 07746-0010300
 Driver handle, 15 x 135L 07749-0010000
 Slide hammer, 3/8’’-16 UNF commercially available 1. Remove the ball bearing (A) from the clutch housing (B) using the 20 40 mm adjustable
bearing puller (C) and a commercially available
3/8’’-16 UNF slide hammer (D).
2. Remove the oil seal (A) from the clutch housing. Be careful when removing the oil seal so the clutch
housing is not damaged. 3. Drive in new oil seal from the transmission side
using the 15 x 135L driver handle (A) and the
42 x 47 mm bearing driver attachment (B).
4. Drive in new ball bearing from the transmission side using the 65 mm oil seal driver (A).
08/08/21 14:48:39 61SNR030_130_0131
ProCarManuals.com
DYNOMITE -2009-

µ
µ

 

(#'


 )
Special Tools Required
13-130
Manual Transmission
Countershaft Bearing Replacement
A
B
C
B
07736-A01000B
A D
D
07JAD-PL90100 A
B C
B
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) A
 Oil seal driver, 65 mm 07JAD-PL90100
 Adjustable bearing puller, 20 40 mm 07736-A01000B
 Slide hammer, 3/8’’-16 UNF commercially available
1. Remove the bearing set plate (A) from the clutch housing (B).
2. Remove the needle bearing (A) using the 20 40 mm adjustable bearing puller (B) and a
commercially available 3/8’’-16 UNF slide hammer
(D), then remove oil guide plate C. 3. Position oil guide plate C and new needle bearing
(A) in the bore of the clutch housing (B).
4. Install the needle bearing using the 65 mm oil seal driver (D).
5. Install the bearing set plate (A) with the bolts (B).
08/08/21 14:48:40 61SNR030_130_0132
ProCarManuals.com
DYNOMITE -2009-



(#'
")
Special Tools Required
13-131
Mainshaft Thrust Clearance Adjustment
A
M B
B
A
C A
07GAJ-PG20110
B
07GAJ-PG20130 D
C
 Catch adapter 07GAJ-PG20110
 Base adapter 07GAJ-PG20130
NOTE:
 Take measurement at normal room temperature.
 Clean all the parts thoroughly before installation.
1. Remove the 72 mm shim (A) and oil guide plate M from the transmission housing (B).
2. Thoroughly clean the 28 mm spring washer (A) and the 28 mm washer (B) before installing them on the
clutch housing side ball bearing (C).
NOTE: Install the spring washer in the direction
shown.
3. Assemble all of the mainshaft components. NOTE: Refer to the Exploded View, as needed
during the assembly (see page 13-113). 4. Install the mainshaft assembly into the clutch
housing.
5. Place the transmission housing over the mainshaft and onto the clutch housing.
6. Tighten the clutch and transmission housings with several 8 mm bolts.
NOTE: It is not necessary to use sealing agent
between the housing for this procedure.
7. Lightly tap on the mainshaft with a plastic hammer.
8. Attach the catch adapter (A) and the base adapter (B) to the mainshaft as follows:
 Back out the catch adapter bolt (C), and loosen the two hex bolts (D).
 Fit the catch adapter over the mainshaft so its lip is towards the transmission.
 Align the catch adapter lip around the groove at the inside of the mainshaft splines, then tighten
the hex bolts.
9. Fully seat the mainshaft by tapping its end with a plastic hammer.
10. Thread the catch adapter bolt in until it just contacts thewidesurfaceofthebaseadapter.
(cont’d)
08/08/21 14:48:41 61SNR030_130_0133
ProCarManuals.com
DYNOMITE -2009-

µµ
µ
Standard: 0.11 0.17 mm (0.004 0.007 in.)
(Example)
Measure reading: 1.93 mm (0.076 in.)
1.93 0.14 = 1.79 mm (0.070 in.) 72 mm Shim
Type Part Number Thickness
13-132Manual Transmission
Mainshaft Thrust Clearance Adjustment (cont’d)
A
07GAJ-PG20130 B
07GAJ-PG20110
11. Zero a dial gauge (A) on the end of the mainshaft.
12. Turn the catch adapter bolt (B) clockwise; stop
turning when the dial gauge has reached its
maximum movement. The reading on the dial
gauge is the amount of mainshaft thrust clearance.
NOTE: Do not turn the catch adapter bolt exceeds
60 degrees after the needle of the dial gauge stops
moving. Applying more pressure with the catch
adapter bolt could damage the transmission.
13. If the reading is within the standard, the clearance is correct. If the reading is not within the standard,
select the appropriate shim needed from the table,
and recheck the thrust clearance.
Subtract the total clearance measurement from the
middle of the clearance standard 0.14 mm
(0.0056 in.)
Select the shim closest to the amount calculated.
For this example, the 1.80 mm (0.071 in.) shim is
best.
14. With oil guide plate M and the appropriate size shim installed in the transmission housing, check
the thrust clearance again to make sure the
clearance is within the standard. A 23931-P21-000 0.60 mm (0.024 in.)
B 23932-P21-000 0.63 mm (0.025 in.)
C 23933-P21-000 0.66 mm (0.026 in.)
D 23934-P21-000 0.69 mm (0.027 in.) E 23935-P21-000 0.72 mm (0.028 in.)F 23936-P21-000 0.75 mm (0.030 in.)
G 23937-P21-000 0.78 mm (0.031 in.) H 23938-P21-000 0.81 mm (0.032 in.) I 23939-P21-000 0.84 mm (0.033 in.)
J 23940-P21-000 0.87 mm (0.034 in.)
K 23941-P21-000 0.90 mm (0.035 in.) L 23942-P21-000 0.93 mm (0.037 in.)
M 23943-P21-000 0.96 mm (0.038 in.) N 23944-P21-000 0.99 mm (0.039 in.)
O 23945-P21-000 1.02 mm (0.040 in.) P 23946-P21-000 1.05 mm (0.041 in.)
Q 23947-P21-000 1.08 mm (0.043 in.) R 23948-P21-000 1.11 mm (0.044 in.)
S 23949-P21-000 1.14 mm (0.045 in.)T 23950-P21-000 1.17 mm (0.046 in.)
U 23951-P21-000 1.20 mm (0.047 in.) V 23952-P21-000 1.23 mm (0.048 in.)
W 23953-P21-000 1.26 mm (0.050 in.) X 23954-P21-000 1.29 mm (0.051 in.)Y 23955-P21-000 1.32 mm (0.052 in.) Z 23956-P21-000 1.35 mm (0.053 in.)
AA 23957-P21-000 1.38 mm (0.054 in.) AB 23958-P21-000 1.41 mm (0.056 in.)
AC 23959-P21-000 1.44 mm (0.057 in.)
AD 23960-P21-000 1.47 mm (0.058 in.) AE 23961-P21-000 1.50 mm (0.059 in.)AF 23962-P21-000 1.53 mm (0.060 in.)
AG 23963-P21-000 1.56 mm (0.061 in.) AH 23964-P21-000 1.59 mm (0.063 in.) AI 23965-P21-000 1.62 mm (0.064 in.)
AJ 23966-P21-000 1.65 mm (0.065 in.)
AK 23967-P21-000 1.68 mm (0.066 in.) AL 23968-P21-000 1.71 mm (0.067 in.)
AM 23969-P21-000 1.74 mm (0.069 in.) AN 23970-P21-000 1.77 mm (0.070 in.)
AO 23971-P21-000 1.80 mm (0.071 in.) (cont’d)
08/08/21 14:48:41 61SNR030_130_0134
ProCarManuals.com
DYNOMITE -2009-

Î Î

13-134Manual Transmission
Transmission Reassembly (cont’d)
6x1.0mm
15 N·m (1.5 kgf·m, 11 lbf·ft)
A
A
D
B
C M
B
C
A
Liquid gasket
4. Install the reverse shift fork (A).
5. Install the reverse idler gear (A) and the reverse idler gear shaft (B) by aligning the mark (C) on the
clutch housing with the r everse idler gear shaft
hole (D). 6. Selectthepropersize72mmshim(A)accordingto
the measurements made during the Mainshaft
Thrust Clearance Adjustment (see page 13-131).
Install the oil gutter plate (B), oil guide plate M, and
the 72 mm shim into the transmission housing (C).
7. Clean any dirt or oil from the mating surface of the transmission housing and the clutch housing.
Apply liquid gasket, P/N 08718-0001 evenly to the
mating surface of the transmission housing and the
clutch housing. Install the component within
5 minutes of applying the liquid gasket.
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket.
08/08/21 14:48:42 61SNR030_130_0136
ProCarManuals.com
DYNOMITE -2009-







Specified Torque:
8x1.25mm
27 N·m (2.8 kgf·m, 20 lbf·ft)
13-136
Manual Transmission
Transmission Reassembly (cont’d)
Liquid gasket A
CB
6x1.0mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft) D
39 N·m
(4.0 kgf·m,
29 lbf·ft)
B
14. Tighten the 8 mm flange bolts in a crisscross
pattern in several steps.
15. Clean any dirt or oil from the mating surface of the change lever assembly and the transmission
housing. Apply liquid gasket, P/N 08718-0001,
evenly to the mating surface of the change lever
assembly and the transmission housing. Install the
component within 5 minutes of applying the liquid
gasket.
NOTE:  If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket. 16. Installthe8x14mmdowelpins(B)andthechange
lever assembly (C) with harness bracket A.
17. Apply liquid gasket, P/N 08718-0001, evenly to the threads of the inter lock bolt (D). Install the
component within 5 minutes of applying the liquid
gasket.
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket.
08/08/21 14:48:44 61SNR030_130_0138
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
13-139
M/T Differential
Component Location Index
CARRIER BEARING
FINAL DRIVEN GEARDIFFERENTIAL CARRIER
CARRIER BEARING
SHIM, 80 mm
OIL SEAL
OIL SEAL
Replacement, page 13-140
Replacement, page 13-140Replacement, page 13-140
Replacement, page 13-140
Differential Thrust Clearance Adjustment, page 13-142
Replacement, page 13-141
Replacement, page 13-141
08/08/21 14:48:56 61SNR030_130_0141
ProCarManuals.com
DYNOMITE -2009-