2006 ACURA CSX oil

Î
Î

(#'

 ) Special Tools Required
13-14113-141
Oil Seal Replacement
B
07746-0030100
C
A
B
07746-0030100
C
A A
B
A
B
3. Install new bearings (A) on with the 40 mm inner driver handle (B) and a press. Press on each
bearing until it bottoms. There should be no
clearance between the bearings and the carrier.
NOTE: Place the seal (C) part of the bearing
towards the outside of the differential, and install it.  Oil seal driver attachment 07NAD-P20A100
 Driver handle, 15 x 135L 07749-0010000
1. Remove the oil seal (A) from the transmission housing (B).
2. Remove the oil seal (A) from the clutch housing (B).
(cont’d)
08/08/21 14:48:57 61SNR030_130_0143
ProCarManuals.com
DYNOMITE -2009-

Î
Î

(#'

 ) Special Tools Required
13-14113-141
Oil Seal Replacement
B
07746-0030100
C
A
B
07746-0030100
C
A A
B
A
B
3. Install new bearings (A) on with the 40 mm inner driver handle (B) and a press. Press on each
bearing until it bottoms. There should be no
clearance between the bearings and the carrier.
NOTE: Place the seal (C) part of the bearing
towards the outside of the differential, and install it.  Oil seal driver attachment 07NAD-P20A100
 Driver handle, 15 x 135L 07749-0010000
1. Remove the oil seal (A) from the transmission housing (B).
2. Remove the oil seal (A) from the clutch housing (B).
(cont’d)
08/08/21 14:48:57 61SNR030_130_0143
ProCarManuals.com
DYNOMITE -2009-



Î
(#'
") Special Tools Required
13-14213-142 M/T Differential
Oil Seal Replacement (cont’d) Differential Thrust Clearance
Adjustment
A
07749-0010000
B
07NAD-P20A100
A
07749-0010000 B
07NAD-P20A100
3. Install a new oil seal flush with the transmission housing with the 15 x 135L driver handle (A) and
the oil seal driver attachment (B).
4. Install a new oil seal flush with the clutch housing with the 15 x 135L driver handle (A) and the oil seal
driver attachment (B). Inner driver handle, 40 mm 07746-0030100
1. If you removed the 80 mm shim from the transmission housing reinstall is the same sized
shim.
2. Install the differential assembly into the clutch housing.
08/08/21 14:48:58 61SNR030_130_0144
ProCarManuals.com
DYNOMITE -2009-



Î
(#'
") Special Tools Required
13-14213-142 M/T Differential
Oil Seal Replacement (cont’d) Differential Thrust Clearance
Adjustment
A
07749-0010000
B
07NAD-P20A100
A
07749-0010000 B
07NAD-P20A100
3. Install a new oil seal flush with the transmission housing with the 15 x 135L driver handle (A) and
the oil seal driver attachment (B).
4. Install a new oil seal flush with the clutch housing with the 15 x 135L driver handle (A) and the oil seal
driver attachment (B). Inner driver handle, 40 mm 07746-0030100
1. If you removed the 80 mm shim from the transmission housing reinstall is the same sized
shim.
2. Install the differential assembly into the clutch housing.
08/08/21 14:48:58 61SNR030_130_0144
ProCarManuals.com
DYNOMITE -2009-

Transmission End Cover
Transmission Housing
Valve Body
Torque Converter HousingShafts and Clutches
A/T Differential...................................
.......................
...........................................
........................................... .....................
...............................
...................................
.......................
...........................................
........................................... .....................
...............................
End Cover Removal
. 14-290
Park Lever Stop Inspection and Adjustment . 14-292
Idler Gear Shaft Bearing Replacement . 14-292
Selector Control Shaft Oil Seal Replacement . 14-293
Selector Control Shaft Bearing Replacement . 14-293
ATF Feed Pipe Replacement . 14-294
End Cover Installation . 14-349
...
....................................... ...................................
.......................
.............................................. ...
....................................... ...................................
.......................
..............................................
Housing and Shaft Assembly Removal . 14-295
Bearing Removal
. 14-297
Bearing Installation . 14-298
Reverse Idler Gear Removal and Installation . 14-299
Shaft Assembly and Housing Installation . 14-344
...
..................................... ...................
.................
................................
.................
.................
.......................
.............................................. ...
..................................... ...................
.................
................................
.................
.................
.......................
..............................................
Valve Body and ATF Strainer Removal . 14-300
Valve Body Repair
. 14-301
Valve Body Valve Installation . 14-302
Main Valve Body Disassembly, Inspection, and Reassembly . 14-303
ATF Pump Inspection . 14-304
Regulator Valve Body Disassembly, Inspection, and Reassembly . 14-305
Servo Body Disassembly, Inspection, and Reassembly . 14-306
Shift Solenoid Valve Removal and Installation . 14-307
Valve Body and ATF Strainer Installation . 14-342
........................................... ...........
........................................... ........................................... ...........
...........................................
Mainshaft Bearing and Oil Seal
Replacement . 14-308
Countershaft Bearing Replacement . 14-309
Secondary Shaft Bearing Replacement . 14-310
Selector Control Shaft Oil Seal Replacement . 14-311 .................
............................................... .................
.................................................. ..............................................
.................
.......................
.............................
............................. .......................
........................................... ...................................
.......................................
............................................... ............................
................
.................
............................................... .................
.................................................. ..............................................
.................
.......................
.............................
............................. .......................
........................................... ...................................
.......................................
............................................... ............................
................
Mainshaft Disassembly,
Inspection, and Reassembly . 14-312
Mainshaft 5th Gear Axial Clearance Inspection . 14-313
Countershaft Disassembly, Inspection, and Reassembly . 14-316
Countershaft Reverse Selector Hub and 3rd Gear
Removal . 14-317
Installation . 14-318
Secondary Shaft Disassembly, Inspection, and Reassembly . 14-319
Secondary Shaft Ball Bearing, Idler Gear Removal and Installation . 14-320
Secondary Shaft 2nd Gear Axial Clearance Inspection . 14-321
Secondary Shaft 1st Gear Axial Clearance Inspection . 14-322
Idler Gear Shaft Removal and Installation . 14-324
Idler Gear/Idler Gear Shaft Replacement . 14-325
Clutch Disassembly . 14-326
Clutch Inspection . 14-330
Clutch Wave-plate Phase Difference Inspection . 14-331
Clutch Clearance Inspection . 14-332
1st, 2nd, and 3rd Clutch Reassembly . 14-335
4th and 5th Clutch Reassembly . 14-338
......................
...................................
........................................... ...................
................................
........................................... ..........
......................
...................................
........................................... ...................
................................
........................................... ..........
Component Location Index
. 14-355
Backlash Inspection . 14-356
Differential Carrier and Final Driven Gear Replacement . 14-356
Carrier Bearing Replacement . 14-357
Oil Seal Replacement . 14-358
Carrier Bearing Outer Race Replacement . 14-359
Carrier Bearing Preload Inspection . 14-362
08/08/21 14:37:02 61SNR030_140_0003
ProCarManuals.com
DYNOMITE -2009-

µ

















(#'


%)
Ref. No. Tool Number DescriptionQty
14-2Automatic Transmission
Special Tools
07GAB-PF50101
Mainshaft Holder 1
07HAJ-PK40201 Preload Inspection Tool 1
07JAD-PH80101 Oil Seal Driver Attachment 1
07LAD-PW50601 Attachment, 40 mm 1
07LAE-PX40000 Clutch Spring Compressor Set 1
07MAJ-PY4011A A/T Pressure Hose, 2,210 mm 3
07MAJ-PY40120 A/T Pressure Hose Adapter 3
07NAD-PX40100 Attachment, 78 x 80 mm 1
07QAD-P0A0100 Attachment, 42 mm I.D. 1
07ZAE-PRP0100 Clutch Compressor Attachment 1
07406-0020401 A/T Oil Pressure Gauge Set 1
07736-A01000B or 07736-A01000A Adjustable Bearing Puller, 25 40 mm 1
07746-0010100 Attachment, 32 x 35 mm 1
07746-0010300 Attachment, 42 x 47 mm 1
07746-0010400 Attachment, 52 x 55 mm 1
07746-0010500 Attachment, 62 x 68 mm 1
07746-0010600 Attachment, 72 x 75 mm 1
07746-001A800 Attachment, 22 x 24 mm 1
07746-0030100 Driver Handle, 40 mm I.D. 1
07749-0010000 Driver 1
07947-SD90101 Oil Seal Driver Attachment 1
07947-ZV00100 Oil Seal Driver Attachment 1
: Must be used with commercially available 3/8 ’’-16 slide hammer.
08/08/21 14:37:04 61SNR030_140_0004
ProCarManuals.com
DYNOMITE -2009-


(#'

)
µ
Stall Speed rpm:
Specification: 2,150 rpm
Service Limit: 2,000 2,300 rpm Problem Probable causes
14-210
Automatic Transmission
Stall Speed Test
A
1. Make sure the transmission fluid is filled to the
proper level (see page 14-231).
2. Apply the parking brake, and block all four wheels.
3. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
4. Turn the ignition switch to ON (II), and go to the A/T Data List. Make sure the HDS communicates with
the PCM. If it does not, go to the DLC circuit
troubleshooting (see page 11- 204).
5. Make sure the A/C switch is OFF.
6. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
7. Shift to D while pressing the brake pedal firmly, then fully press the accelerator pedal for
6 to 8 seconds, and note the engine speed. Do not
move the shift lever or remove your foot off the
brake pedal while raising the engine speed.
8. Allow 2 minutes for cooling, then repeat the test in SandR.
NOTE: Do not test the stall speed for more than 10 seconds at a time.
 The stall speed tests should be used for diagnostic purposes only.
 Stall speed test results should be the same with the shift lever in D, S, and R.
 Do not test the stall speed with the A/T oil pressure gauges installed. 9. If the stall speeds are out of the service limit, the
problems and probable causes are listed in the
table.







Stall speed rpm high
in D, S, and R
ATF pump output
low
Clogged ATF strainer
Regulator valve stuck
Slipping clutch
Stall speed rpm high
in R Slippage of 4th clutch
Stall speed rpm low
in D, S, and R Engine output low
Engine throttle valve
closed
Torque converter
one-way clutch
slipping
08/08/21 14:46:42 61SNR030_140_0212
ProCarManuals.com
DYNOMITE -2009-

µµ
µ
 Î

(#'


)
Special Tools Required
Pressure Fluid PressureStandard Service Limit
14-211
Pressure Test
A
A/T OIL PRESSURE
GAUGE SET
07406-0020401
A/TPRESSUREHOSE,
2,210 mm
07MAJ-PY4011A
(3 required) A/T PRESSURE
HOSE ADAPTER
07MAJ-PY40120
(3 required)
A
 A/T oil pressure gauge set 07406-0020401
 A/T pressure hose, 2,210 mm 07MAJ-PY4011A
 A/T pressure hose adapter 07MAJ-PY40120
NOTE:
 Disable the VSA by pressing the VSA OFF switch (if equipped).
 VSA DTC(s) may come on during the pressure test. If the VSA(s) come on, clear the DTC(s) with the HDS.
1. Make sure the transmission fluid is filled to the proper level (see page 14-231).
2. Raise the vehicle on a lift, or apply the parking brake, block rear wheels, and raise the front of the
vehicle. Make sure it is securely supported.
3. Remove the splash shield.
4. Allow the front wheels to rotate freely.
5. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
6. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go
to the DLC circuit troubleshooting (see page
11-204). 7. Connect the A/T oil pressure gauge to the line
pressure inspection port (A). Do not allow dust or
other foreign particles to enter the ports while
connecting the gauges.
8. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
9. Measure the line pressure at the line pressure inspection port with the shift lever in P or N while
holding the engine speed at 2,000 rpm.
NOTE: Higher pressure may be indicated if
measurements are made in shift lever position
other than P or N.
Line 900 960 kPa (9.2 9.8 kgf/cm ,
130 140 psi) 850 kPa
(8.7 kgf/cm ,
120 psi)
10. Turn the engine off, then disconnect the A/T oil pressure gauge from the line pressure inspection
port.
11. Install the sealing bolt to the line pressure inspection port with a new sealing washer, and
tighten the bolt to 18 N·m (1.8 kgf·m, 13 lbf·ft). Do
not reuse the old sealing washer.
(cont’d)
22
08/08/21 14:46:42 61SNR030_140_0213
ProCarManuals.com
DYNOMITE -2009-