2006 ACURA CSX lock

Cavity Wire Test conditionTest: Desired result Possible cause if desired result is
not obtained
22-136Keyless/Power Door Locks/Security System
MICU Input Test (cont’d)






























T27 GRY Driver door lock
switch unlocked Measure the voltage to ground:
There should be less than 1 V. Poor ground (G503)
Faulty driver door lock switch
An open in the wire
Driver door lock
switch in neutral or
locked Measure the voltage to ground:
There should be more than 5 V.
Faulty driver door lock switch
A short to ground in the wire
T28 GRN Driver door lock switch locked Measure the voltage to ground:
There should be less than 1 V. Poor ground (G503)
Faulty driver door lock switch
An open in the wire
Driver door lock
switch in neutral or
unlocked Measure the voltage to ground:
There should be more than 5 V.
Faulty driver door lock switch
A short to ground in the wire
T29 PUR Front passenger’s door lock switch
unlocked Measure the voltage to ground:
There should be less than 1 V.
Poor ground (G504)
Faulty front passenger’s door
lock switch
An open in the wire
Front passenger’s
door lock switch in
neutral or locked Measure the voltage to ground:
There should be more than 5 V.
Faulty front passenger’s door
lock switch
A short to ground in the wire
T30 YEL Front passenger’s door lock switch
locked Measure the voltage to ground:
There should be less than 1 V.
Poor ground (G504)
Faulty front passenger’s door
lock switch
An open in the wire
Front passenger’s
door lock switch in
neutral or
unlocked Measure the voltage to ground:
There should be more than 5 V.
Faulty front passenger’s door
lock switch
A short to ground in the wire
T31 BRN Driver door key cylinder switch
unlocked Measure the voltage to ground:
There should be less than 1 V.
Poor ground (G501)
Faulty driver door key cylinder
switch
An open in the wire
Driver door key
cylinder switch in
neutral or locked Measure the voltage to ground:
There should be more than 5 V.
Faulty driver door key cylinder
switch
A short to ground in the wire
T32 ORN Driver door key cylinder switch
locked Measure the voltage to ground:
There should be less than 1 V.
Poor ground (G501)
Faulty driver door key cylinder
switch
An open in the wire
Driver door key
cylinder switch in
neutral or
unlocked Measure the voltage to ground:
There should be more than 5 V.
Faulty driver door key cylinder
switch
A short to ground in the wire
08/08/21 14:26:05 61SNR030_220_0138
ProCarManuals.com
DYNOMITE -2009-


Î

(#'
)
Driver’s Door and Left Rear Door Front Passenger’s Door and Right Rear Door
22-137
Door Lock Actuator Test
A
B
Terminal
Position 12
LOCK
UNLOCK A
B
Terminal
Position 34
LOCK
UNLOCK
1. Remove the door panel (see page 20-7).
2. Disconnect the 10P connector (A) from the actuator (B).
NOTE: The illustration shows the driver’s door.
3. Check actuator operation by connecting power and ground according to the table. To pr event damage
to the actuator, apply battery voltage only
momentarily.
4. If the actuator does not operate as specified, replace it. 1. Remove the door panel.
 Front door panel (see page 20-7)
 Rear door panel (see page 20-17)
2. Disconnect the 10P connector (A) from the actuator (B).
NOTE: The illustration shows the front passenger’s
door.
3. Check actuator operation by connecting power and ground according to the table. To prevent damage
to the actuator, apply battery voltage only
momentarily.
4. If the actuator does not operate as specified, replace it.
08/08/21 14:26:05 61SNR030_220_0139
ProCarManuals.com
DYNOMITE -2009-

¦§ ¦§
¦§

Î
(#'


)
Driver’s Door Passenger’s Door
22-138Keyless/Power Door Locks/Security System
Door Lock Knob Switch Test
A
B
Left rear door
AB
Front passenger’s door,
Right rear door
1. Remove the driver’s door panel (see page 20-7).
2. Disconnect the 10P connector (A) from the actuator
(B).
3. Check for continuity between the terminals.  There should be continuity between terminalsNo. 6 and No. 5 when the door lock knob switch
is in the LOCK position and no continuity when
the switch is in the UNLOCK position.
 There should be continuity between terminals No. 7 and No. 5 when the door lock knob switch
is in the UNLOCK position and no continuity
when the switch is in the LOCK position.
4. If the continuity is not as specified, replace the door lock actuator. 1. Remove the passenger’s door panel (see page
20-7).
2. Disconnect the 10P connector (A) from the actuator (B).
3. Check for continuity between the terminals. There should be continuity between terminals
No. 8 No. 7 and No. 10 No. 5 when the
door lock knob switch in the UNLOCK position and
no continuity when the switch is in the LOCK
position. : Left rear door
4. If the continuity is not specified, replace the door lock actuator.
08/08/21 14:26:06 61SNR030_220_0140
ProCarManuals.com
DYNOMITE -2009-



(#'

)
Driver’s door Front passenger’s door
22-139
Door Lock Switch Test
1. Remove the power window master switch and
disconnect its connector (see page 22- 219).
2. Check for continuity between the power window master switch 22P connector terminals.
 There should be continuity between terminals No. 11 and No. 17 when the door lock switch is in
the LOCK position. (With security)
 There should be no continuity between terminals No. 11 and No. 17 when the door lock switch is in
the UNLOCK position. (With security)
 There should be continuity between terminals No. 11 and No. 19 when the door lock switch is in
the UNLOCK position.
 There should be no continuity between terminals No. 11 and No. 19 when the door lock switch is in
the LOCK position.
3. If the continuity is not as specified, replace the power window master switch. 1. Remove the front passenger’s power window
switch (see page 22-220).
NOTE: The illustration shows the front passenger’s
door.
2. Check for continuity between the front passenger’s power window switch 8P connector terminals.
 There should be continuity between terminals No. 1 and No. 2 when the door lock switch is in
the LOCK position.
 There should be no continuity between terminals No. 1 and No. 2 when the door lock switch is in
the UNLOCK position.
 There should be continuity between terminals No. 2 and No. 6 when the door lock switch is in
the UNLOCK position.
 There should be no continuity between terminals No. 2 and No. 6 when the door lock switch is in
the LOCK position.
3. If the continuity is not as specified, replace the front passenger’s window switch.
08/08/21 14:26:06 61SNR030_220_0141
ProCarManuals.com
DYNOMITE -2009-


(#')
22-140Keyless/Power Door Locks/Security System
Door Key Cylinder Switch Test
A
B
1. Remove the driver’s door panel (see page 20-7).
2. Disconnect the 10P connector (A) from the key
cylinder switch (B).
3. Check for continuity between the terminals.  There should be continuity between terminalsNo. 9 and No. 5 when the door key cylinder
switch is in LOCK position. (With security)
 There should be no continuity between terminals No. 9 and No. 5 when the door key cylinder
switch is in the neutral or UNLOCK position.
(With security)
 There should be continuity between terminals No. 8 and No. 5 when the door key cylinder
switch is in UNLOCK position.
 There should be no continuity between terminals No. 8 and No. 5 when the door key cylinder
switch is in the neutral or LOCK position.
4. If the continuity is not as specified, replace the door key cylinder assembly (see page 20-9).
08/08/21 14:26:06 61SNR030_220_0142
ProCarManuals.com
DYNOMITE -2009-



(#'

)
With HDS
22-142 Keyless/Power Door Locks/Security System
Transmitter Test/Replacement
A
NOTE:
 If the doors unlock or lock with the transmitter, but the LED on the transmitter does not come on, the LED
is faulty; replace the transmitter.
 If any door is open, you cannot lock the doors with the transmitter.
 If you unlocked the doors with the transmitter, but do not open any of the doors within 30 seconds, the
doors relock automatically.
 The doors do not lock or unlock with the transmitter if the ignition key is inserted in the ignition switch.
1. Press the lock or unlock button five or six times to reset the transmitter.
 If the locks work, the transmitter is OK.
 If any of the transmitter buttons do not work, replace the transmitter, then do the transmitter
programming registration (see page 22-329).
 If the locks don’t work, go to step 2.
2. Connect the HDS to the data link connector.
3. Select the KEYLESS from the BODY ELECTRICAL menu, then enter the KEYLESS CHECK.
4. Press lock, unlock, trunk, or panic button and check the response on the screen of the HDS.
NOTE: The door lock actuators may or may not
cycle when receiving input from the transmitter.
 If KEYLESS ENTRY TRANSMITTER CODE IS RECEIVED is indicated, the transmitter is OK. Go
to keyless operation troubleshooting (see page
22-127).
 If DIFFERENT KEYLESS ENTRY TRANSMITTER CODE IS RECEIVED is indicated, the transmitter is
not registered to the vehicle, if necessary,
reprogram and register the transmitter (see page
22-329).
 If KEYLESS ENTRY TRANSMITTER CODE IS NOT RECEIVED is indicated, go to step 5. 5. Open the transmitter and check for water damage.
 If you find any water damage, replace thetransmitter, then reprogram and register the
transmitter (see page 22-329).
 If there is no water damage, go to step 6.
6. Replace the transmitter battery (A) with a new one, and press lock or unlock button and check the
receive condition on the screen of the HDS.
 If KEYLESS ENTRY TRANSMITTER CODE IS RECEIVED is indicated, the transmitter is OK.
 If KEYLESS ENTRY TRANSMITTER CODE IS NOT RECEIVED is indicated, go to step 7.
08/08/21 14:26:07 61SNR030_220_0144
ProCarManuals.com
DYNOMITE -2009-


Without HDS
22-143
7. Use a different known-good keyless transmitterand repeat steps 3 and 4.
NOTE: The keyless transmitter does not need to be
programmed to the vehicle for this test.
 If (DIFFERENT) KEYLESS ENTRY TRANSMITTER CODE IS RECEIVED is indicated, replace the
keyless transmitter and do the immobilizer
system registration (see page 22-329).
 If KEYLESS ENTRY TRANSMITTER CODE IS NOT RECEIVED is indicated, the immobilizer-keyless
control unit is faulty, replace it and do the
immobilizer system registration (see page
22-329).
NOTE: As the keyless transmitter is combined with
the immobilizer transponder, when the
transponder is registered by the HDS, the keyless
transmitter programming is completed
automatically. 1. Start the engine.
 If the engine does not start, go to the immobilizersymptom troubleshooting (see page 22-323).
 If the engine starts, go to step 2.
2. Press the lock or unlock button five or six times to reset the transmitter.
 If the locks work, the transmitter is OK.
 If the locks don’t work, go to step 3.
3. Open the transmitter and check for water damage.  If you find any water damage, replace thetransmitter.
 If there is no water damage, go to step 4.
(cont’d)
08/08/21 14:26:07 61SNR030_220_0145
ProCarManuals.com
DYNOMITE -2009-


22-144Keyless/Power Door Locks/Security System
Transmitter Test/Replacement (cont’d)
A
4. Replace the transmitter battery (A) with a new one,
and try to lock and unlock the doors with the
transmitter by pressing the lock or unlock button
five or six times.
 If the doors lock and unlock, the transmitter is OK.
 If the doors don’t lock and unlock, go to step 5.
5. Reprogram and register the transmitter (see page 22-329), then try to lock and unlock the doors.
 If the doors lock and unlock, the transmitter is OK.
 If the doors don’t lock and unlock, substitute a known-good transmitter and recheck (see page
22-329). If still not operating, replace the
immobilizer-keyless control unit.
08/08/21 14:26:07 61SNR030_220_0146
ProCarManuals.com
DYNOMITE -2009-