2005 TOYOTA AVENSIS fuel pressure

05±312
±
DIAGNOSTICS SFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E) 


\f  
*
1
CHK ENG
 
 \b
P0174 *3
(05±394)System too Lean (Bank2)

Air induction system

Injector blockage

Mass air flow meter

Manifold absolute pressure sensor

Engine coolant temperature sensor

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 2 sensor 1)
circuit

Heated oxygen sensor (bank 2 sensor 1)

Heated oxygen sensor heater (bank 2 sensor 1)

EFI relay

PCV valve and hose

PCV hose connection

ECM

P0175 *3
(05±394)System too Rich (Bank2)

Injector leak, blockage

Mass air flow meter

Manifold absolute pressure sensor

Engine coolant temperature sensor

Ignition system

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 2 sensor 1)
circuit

Heated oxygen sensor (bank 2 sensor 1)

ECM

P0190
(05±406)Fuel Rail Pressure Sensor Cir-
cuit
Open or short in fuel pressure sensor circuit

Fuel pressure sensor

ECM

P0191
(05±410)Fuel Rail Pressure Sensor Cir-
cuit Range/Performance

Open or short in high±pressure fuel pump (spill valve) circuit

High±pressure fuel pump

Low±pressure fuel pump

Fuel pipe

Fuel relief valve

Fuel pressure regulator

ECM

P0200
(05±415)Injector Circuit/Open
P0201
(05±415)Injector Circuit/Open ±
(Cylinder 1)

Open or short in EDU circuit
P0202
(05±415)Injector Circuit/Open ±
(Cylinder 2)

Oen or short in EDU circuit

EDU (Injector driver)

Fuel injector assy
P0203
(05±415)Injector Circuit/Open ±
(Cylinder 3)
jy

ECM
P0204
(05±415)Injector Circuit/Open ±
(Cylinder 4)
P0220
(05±356)Throttle/Pedal Position Sensor/
Switch ºBº Circuit
Throttle position sensor (built in throttle body)

ECM
P0222
(05±356)Throttle/Pedal Position Sensor/
Switch ºBº Circuit Low Input

Throttle position sensor (built in throttle body)

VTA2 circuit short

VC circuit open

ECM

P0223
(05±356)Throttle/Pedal Position Sensor/
Switch ºBº Circuit High Input

Throttle position sensor (built in throttle body)

VTA2 circuit open

E2 circuit open

VC and VTA2 circuit are short±circuited

ECM


±
DIAGNOSTICS SFI SYSTEM (1AZ±FSE)
05±313
AVENSIS REPAIR MANUAL (RM1018E)


\f  
*
1
CHK ENG
 
 \b
P0300 *3
(05±420)
Random/Multiple Cylinder Misfire
Detected
Open or short in engine wire

Connector connection


Vacuum hose connection
*2
P0301 *3
(05±420)Cylinder 1 Misfire Detected

Vacuum hose connection

Ignition system

Injector

Fuelpressure
*2
P0302 *3
(05±420)Cylinder 2 Misfire Detected

Fuel pressure

Mass air flow meter

Engine coolant temperature sensor

Compressionpressure
*2
P0303 *3
(05±420)Cylinder 3 Misfire Detected

Compression pressure

Valve clearance

Valve timing
PCV h ti
*2
P0304 *3
(05±420)Cylinder 4 Misfire Detected

PCV hose connection

PCV hose

ECM
*2
P0325
(05±429)Knock Sensor 1 Circuit (Bank 1
or Single Sensor)
Knock sensor

Knock sensor (under±torqued or loose)

ECM

P0327
(05±429)Knock Sensor 1 Circuit Low In-
put (Bank 1 or Single Sensor)
Short in knock sensor circuit

Knock sensor

ECM

P0328
(05±429)Knock Sensor 1 Circuit High In-
put (Bank 1 or Single Sensor)
Open in knock sensor circuit

Knock sensor

ECM

P0335
(05±433)Crankshaft Position Sensor ºAº
Circuit
Open or short in crankshaft position sensor circuit

Crankshaft position sensor
P0339
(05±433)Crankshaft Position Sensor ºAº
Circuit Intermittent
Crankshaft osition sensor

Signal plate (crankshaft position sensor plate No. 1)

ECM

P0340
(05±436)Camshaft Position Sensor ºAº
Circuit (Bank 1 or Single Sensor)
Open or short in camshaft position sensor circuit

Camshaft position sensor
P0341
(05±436)Camshaft Position Sensor ºAº
Circuit Range/Performance
(Bank 1 or Single Sensor)
Camshaft osition sensor

Camshaft timing gear

Timing chain has jumped a tooth

ECM

P0351
(05±439)Ignition Coil ºAº Primary/Sec-
ondary Circuit

Ignition system

P0352
(05±439)Ignition Coil ºBº Primary/Sec-
ondary Circuit
Ignition system

Open or short in IGF and IGT circuit from ignition coil with
igniter to ECM (ignition coil circuit 1 through 4)
P0353
(05±439)Ignition Coil ºCº Primary/Sec-
ondary Circuit
igniter to ECM (ignition coil circuit 1 through 4)

Ignition coil with igniter (ignition coil 1 through 4)

IG2 relay
P0354
(05±439)Ignition Coil ºDº Primary/Sec-
ondary Circuit
ECM
P0420 *3
(05±446)
Catalyst System Efficiency Be-
low Threshold (Bank 1)
Gas leakage in exhaust system

Heated oxygen sensor

P0430 *3
(05±446)
Catalyst System Efficiency Be-
low Threshold (Bank 2)
Heated oxygen sensor

Three±way catalytic converter (inside exhaust manifold)

P0443
(05±449)Evaporative Emission Control
System Purge Control Valve Cir-
cuit
Open of short in VSV circuit for EVAP

VSV for EVAP

ECM

P0500
(05±453)Vehicle Speed Sensor ºAº

Combination meter

Open or short in speed sensor circuit

Vehicle speed sensor

ECM

Skid control ECU

Clutch or brake slips or gear is broken

P0504
(05±455)Brake Switch Correlation

Short in stop light switch signal circuit

Stop light switch

ECM



±
DIAGNOSTICS SFI SYSTEM (1AZ±FSE)
05±315
AVENSIS REPAIR MANUAL (RM1018E)


\f  
*
1
CHK ENG
 
 \b
P0746 *3,4
(05±954)
Pressure Control Solenoid ºAº
Performance (Shift Solenoid
Valve SL1)

Electronic controlled automatic transmission (ECT)
P0748 *4
(05±956)
Pressure Control Solenoid ºAº
Electrical (Shift Solenoid Valve
SL1)

Electronic controlled automatic transmission (ECT)
P0766 *3,4
(05±962)
Shift Solenoid ºDº Performance
(Shift Solenoid Valve S4)
Electronic controlled automatic transmission (ECT)
P0776 *3,4
(05±963)
Pressure Control Solenoid ºBº
Performance (Shift Solenoid
Valve SL2)

Electronic controlled automatic transmission (ECT)
P0778 *4
(05±956)
Pressure Control Solenoid ºBº
Electrical (Shift Solenoid Valve
SL2)

Electronic controlled automatic transmission (ECT)
P0793 *4
(05±965)
Intermediate Shaft Speed Sen-
sor ºAº Circuit No Signal
Electronic controlled automatic transmission (ECT)
P0982 *4
(05±956)Shift Solenoid ºDº Control Low
Electronic controlled automatic transmission (ECT)
P0983 *4
(05±956)Shift Solenoid ºDº Control High
Electronic controlled automatic transmission (ECT)
P1235
(05±477)High Pressure Fuel Pump Circuit

Open or short in fuel pump (high pressure)

Fuel pump (high pressure)

ECM

P2008
(05±480)Intake Manifold Runner Control
Circuit/Open (Bank 1)
Open of short in VSV for IACV circuit

VSV for IACV

ECM

P2102
(05±483)Throttle Actuator Control Motor
Circuit Low
Open in throttle control motor circuit

Throttle control motor

ECM

P2103
(05±483)Throttle Actuator Control Motor
Circuit High
Short in throttle control motor circuit

Throttle control motor

ECM

P2111
(05±485)Throttle Actuator Control System
± Stuck Open
Throttle control motor circuit

Throttle control motor
P2112
(05±485)Throttle Actuator Control System
± Stuck Closed
Throttle body

Throttle valve
P2118
(05±487)Actuator Control Motor Current
Range/Performance
Open in ETCS power source circuit

ECM
P2119
(05±490)Throttle Actuator Control Throttle
Body Range/Performance
Electric throttle control system

ECM
P2120
(05±492)Throttle/Pedal Position Sensor/
Switch ºDº Circuit
Open or short in accelerator pedal position sensor circuit

Accelerator pedal position sensor

ECM

P2121
(05±499)Throttle/Pedal Position Sensor/
Switch ºDº Circuit Range/Perfor-
mance
Open or short in accelerator pedal position sensor circuit

Accelerator pedal position sensor

ECM


05±316
±
DIAGNOSTICS SFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E) 


\f  
*
1
CHK ENG
 
 \b
P2122
(05±492)Throttle/Pedal Position Sensor/
Switch ºDº Circuit Low Input
P2123
(05±492)Throttle/Pedal Position Sensor/
Switch ºDº Circuit High Input
P2125
(05±492)Throttle/Pedal Position Sensor/
Switch ºEº Circuit
Same as DTC No. P2120
P2127
(05±492)Throttle/Pedal Position Sensor/
Switch ºEº Circuit Low Input
P2128
(05±492)Throttle/Pedal Position Sensor/
Switch ºEº Circuit High Input
P2135
(05±356)Throttle Pedal Position Sensor/
Switch ºAº/ºBº Voltage Correla-
tion
VTA1 and VTA2 circuit are short±circuited

Throttle position sensor (built in throttle body)

ECM

P2138
(05±492)Throttle Pedal Position Sensor/
Switch ºDº/ºEº Voltage Correla-
tion

Same as DTC No. P2120
P2195 *3
(05±363)
Oxygen Sensor Signal Stuck
Lean (Bank 1 Sensor 1)
Open or short in heated oxygen sensor (bank 1, 2 sensor 1)
circuit
P2196 *3
(05±363)
Oxygen Sensor Signal Stuck
Rich (Bank 1 Sensor 1)
Heated oxygen sensor (bank 1, 2 sensor 1)

Heated oxygen sensor heater (bank 1, 2 sensor 1)

EFI relay

P2197 *3
(05±363)
Oxygen Sensor Signal Stuck
Lean (Bank 2 Sensor 1)
EFI relay

Air induction system

Fuel pressure

P2198 *3
(05±363)
Oxygen Sensor Signal Stuck
Rich (Bank 2 Sensor 1)

Fuel ressure

Injector

ECM
P2716 *4
(05±967)
Pressure Control Solenoid ºDº
Electrical
Electronic controlled automatic transmission (ECT)
B2799
(05±1625)Engine Immobiliser System Mal-
function
Immobiliser system

*1: CHK ENG (Check engine warning light) is illuminated
*
2: CHK ENG (Check engine warning light) is illuminated or blinks
*
3: For Euro±OBD vehicles only.
*
4: For A/T only.

05±300
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
4. FAIL±SAFE CHART
If any of the following codes is recorded, the ECM enters into the fail±safe mode.
DTC No.Fail±Safe OperationFail±Safe Deactivation Conditions
P0031
P0032
P0037
P0038
P0051
P0052
P0057
P0058
Faulty heater circuit is turned off.Ignition switch is OFF.
P0100
P0102
P0103Ignition timing is calculated based on an engine speed and
a throttle opening angle.ºPassº detection has occurred. Upon this occurrence, the
ECM will return to normal mode.
P0105
P0107
P0108
Intake air pressure is controlled with a calculated value in
proportion to the throttle opening angle and the engine
speed.

Limit the engine speed to 3,000 rpm or less.
ºPassº detection has occurred. Upon this occurrence, the
ECM will return to normal mode.
P0110
P0112
P0113
Intake air temperature is fixed at 20 C (68 F)ºPassº detection has occurred. Upon this occurrence, the
ECM will return to normal mode.
P0115
P0117
P0118
Engine coolant temperature is fixed at 80   ºPassº detection has occurred. Upon this occurrence, the
ECM will return to normal mode.
P0120
P0121
P0122
P0123
P0220
P0222
P0223
P2135
Turn off the power for the throttle motor, return the throttle
valve in position using the return spring, and fuel cut inter-
mittent.Repeat the following conditions at least 2 seconds or more
with the throttle position switch closed:

VTA is more than 0.1 V but less than 0.95 V

Engine speed is 0 km/h
P0190
P0191
Stop the high±pressure pump operation.

Limit the engine speed to 2,000 rpm or less.After it is returned to normal condition, turn the ignition switch
ON.
P0200Turn off the INJ relay and cut the power for the EDU.
P0201
P0202
P0203
P0204
Stop fuel injection for an abnormal cylinder and related
other cylinders.

Limit the engine speed to 3,000 rpm or less.After it is returned to normal condition, turn the ignition switch
ON.
P0325
P0327
P0328
Maximum timing retardationIgnition switch is OFF.
P0351
P0352
P0353
P0354
Stop fuel injection for all the cylinders.ºPassº detection has occurred. Upon this occurrence, the
ECM will return to normal mode.
P0604
P0606
P0607
P0657Turn off the power for the throttle motor, return the throttle
valve in position using the return spring, and fuel cut inter-
mittent.After it is returned to normal condition, turn the ignition switch
ON.
P1235
Stop the high±pressure pump operation.

Limit the engine speed to 2,000 rpm or less.After it is returned to normal condition, turn the ignition switch
ON.
P2008Force IACV to close.After it is returned to normal condition, turn the ignition switch
ON.

± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±305
AVENSIS REPAIR MANUAL (RM1018E)Hand±held Tester DisplayDiagnostic Note Normal Condition *
1Measurement Item/Range
(Display)
ELECT LOAD SIGElectrical load signal/
ON or OFF
Tail light switch ON: ON

Defogger switch ON: ON

STOP LIGHT SWStop light switch/
ON or OFF
Brake pedal depressed: ON

Brake pedal released: OFF

PS OIL PRESS SWPower steering signal/
ON or OFF

While turning the steering wheel:
ON

While not turning the steering
wheel: OFF
The idle±up control is performed
when PS is ON.
PS SIGNALPower steering signal/
ON or OFFWhen the steering wheel is turned:
ONThis signal is usually ON status
until the IG switch is turned OFF.
SCV VSVVSV status for intake air control
valve/ ON or OFFVSV operation: ON

FUEL PUMP / SPDFuel pump/speed status/
ON/H or OFF/M,LIdling: ON

EVAP VSVVSV status for EVAP control/
ON or OFFVSV operating: ONVSV for EVAP is controlled by the
ECM (ground side duty control)
VVT CTRL B1VVT control status (bank 1)/
ON or OFFVVT system operation: ON

IGNITIONIgnition counter/ Min.: 0, Max.: 4000 to 400

CYL #1, #2, #3, #4Misfire ratio of the cylinder 1 to 4/
Min.: 0 %, Max.: 50 %0 %This item is displayed in only idling
MISFIRE RPMEngine RPM for first misfire range/
Min.: 0 rpm, Max.: 6,375 rpmMisfire 0: 0 rpm

FC TAUFuel Cut TAU: Fuel cut during very
light load/ ON or OFFFuel cut operating: ON
The fuel cut is being performed un-
der very light load to prevent the
engine combustion from becoming
incomplete.
CHECK MODECheck mode/ ON or OFFCheck mode ON: ONSee step 3
O2 RL B1 S2
Oxygen sensor rich lean bank 1
sensor 2:
Response time for oxygen sensor
output to switch from rich to lean/
Min.: 0 ms, Max.: 16,702.5 ms
Idling after warming up:
O2 RL B2 S2
Oxygen sensor rich lean bank 2
sensor 2:
Response time for oxygen sensor
output to switch from rich to lean/
Min.: 0 ms, Max.: 16,702.5 ms
Idling after warming u:
0 to 1,000 msec.

MIL ON RUN DIST
Distance since activation of check
engine warning light/
Min.: 0 km, Max.: 65,535 km
When there is no DTC: 0 km

FUEL PRESS
Fuel high pressure inside fuel de-
livery pipe/
Min.: 0 MPa, Max.: 819 MPa
Idling: 8 to 13 MPa

Running without load (3,000
rpm): 9.5 to 10.5 MPa


*1: If no conditions are specifically stated for ºldlingº, it means the shift lever is at the N or P position, the A/C
switch is OFF and all accessory switches are OFF.
*
2: For A/T only

05±308
±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
6CHECK IGNITION TIMING (See page 14±181)
NGPROCEED TO PAGE AND CONTINUE TO TROU- BLESHOOT
OK
PROCEED TO PROBLEM SYMPTOMS TABLE ON PAGE 05±320
7CHECK FUEL PRESSURE (See page 11±33)
NGPROCEED TO PAGE 11±33 AND CONTINUE TO TROUBLESHOOT
OK
8CHECK FOR SPARK (See page 18±12)
NGPROCEED TO PAGE 18±12 AND CONTINUE TO TROUBLESHOOT
OK
PROCEED TO PROBLEM SYMPTOMS TABLE ON PAGE 05±320

A01512
(V)
(3.96)
3.6
2.4
1.2
150 450
750(840)mmHg
kPa
20 60 100(112)
Manifold Absolute PressureOutput Voltage
05±342
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
DTC P0105 MANIFOLD ABSOLUTE
PRESSURE/BAROMETRIC PRESSURE
CIRCUIT
DTC P0107 MANIFOLD ABSOLUTE
PRESSURE/BAROMETRIC PRESSURE
CIRCUIT LOW INPUT
DTC P0108 MANIFOLD ABSOLUTE
PRESSURE/BAROMETRIC PRESSURE
CIRCUIT HIGH INPUT
CIRCUIT DESCRIPTION
By a built±in sensor unit, the manifold absolute pressure sensor
detects the intake manifold pressure as a voltage. The ECM
then determines the basic injection duration and basic ignition
advance angle based on this voltage.
Since the manifold absolute pressure sensor does not use the
atmospheric pressure as a criterion, but senses the absolute
pressure inside the intake manifold (the pressure in proportion
to the preset absolute vacuum 0), it is not influenced by fluctua-
tions in the atmospheric pressure due to high altitude and other
factors. This permits it to control the air fuel ratio at the proper
level under all conditions.
If the ECM detects the DTC ºP0105, P0107 or P0108º, it oper-
ates the fail±safe function, keeping the ignition timing and fuel
injection volume constant and making it possible to drive the ve-
hicle.
DTC No.DTC Detection ConditionTrouble Area
P0105Open or short in manifold absolute pressure sensor circuit for
0.5 sec. or more
Open or short in manifold absolute pressure sensor circuit
P0107Open in manifold absolute pressure sensor circuit for 0.5 sec.
or more
Open or short in manifold absolute pressure sensor circuit

Manifold absolute pressure sensor


ECM
P0108Short in manifold absolute pressure sensor circuit for 0.5 sec.
or more
ECM
HINT:
After confirming DTC ºP0105, P0107 or P0108º, use the hand±held tester to confirm the manifold absolute
pressure from ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALLº.
Manifold Absolute Pressure (kPa)Malfunction
Approximately 0
PIM circuit short
142 or more

VC circuit open or short

PIM circuit open

E2 circuit open
05CJF±01