2005 TOYOTA AVENSIS radiator

141NH−01
A85614
Clip
ClipRetainer
8.0 (82, 71 in.
lbf)
Engine Cover Sub−assy No. 1
Clip
Engine Under Cover RH
Clip
w/ A/C:
V (Cooler
Compressor to
Crankshaft
Pulley) Belt No. 1
Engine Mounting Insulator Sub−assy RH
x3
5.5 (56, 49 in.·lbf)
Injector Driver
39 (398, 29)
72 (734, 53)
52 (530, 38)
Power Steering
Idle Pulley
Bracket
52 (530, 38)
52 (530, 38)
Radiator Support Opening Cover
: Specified torqueN·m (kgf·cm, ft·lbf)Engine Wire Vacuum Hose
Engine Under Cover Sub−assy No. 1 14−136
− ENGINE MECHANICALTIMING BELT (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
TIMING BELT (1CD−FTV)(From September, 2003)
COMPONENTS

141NG−01
A84393
(a)
(a)
(b)(b)
(a)
A84286
14 −108−
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1CD −FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEELS
2. REMOVE ENGINE UNDER COVER LH
3. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
4. REMOVE ENGINE UNDER COVER RH
5. REMOVE RADIATOR SUPPORT OPENING COVER
6. REMOVE ENGINE ROOM COVER SIDE
7. DRAIN ENGINE COOLANT (See page 16 −19)
8. DRAIN ENGINE OIL (See Pub No. RM1018E on page 17 −30)
9. DRAIN MANUAL TRANSAXLE OIL
Torque: 49 N
m (500 kgf
cm, 36 ft
lbf)
10. REMOVE ENGINE COVER SUB −ASSY NO.1
(a) Remove the 5 nuts, then remove the engine cover.
11. REMOVE BATTERY
12. REMOVE AIR CLEANER ASSY
(a) Disconnect the mass air flow meter connector.
(b) Remove the air cleaner cap together with the air cleaner hose.
(c) Remove the air cleaner filter element.
(d) Remove the 3 bolts and air cleaner case.
13. REMOVE VACUUM RESERVOIR SUB −ASSY
(a) Disconnect the 2 vacuum hoses and connector.
(b) Remove the 2 bolts and vacuum reservoir.
14. REMOVE FUEL FILTER ASSY (See Pub. No. RM1018E on page 11 −82)
15. REMOVE RADIATOR HOSE INLET
16. REMOVE RADIATOR HOSE OUTLET
17. DISCONNECT WATER BY−PASS HOSE NO.2

A84285
A87968
Air Hose No. 3
(a)(b)
(a)
(b)
A79178
− ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD−FTV)(From September,
2003)14−109
AVENSIS Supplement (RM1045E)
18. REMOVE ENGINE ROOM RELAY BLOCK NO.3
(a) Remove the 2 bolts, then remove the engine room relay
block.
19. REMOVE RADIATOR ASSY (W/ AIR CONDITIONING)
(See Pub. No. RM1018E on page 16−51)
20. DISCONNECT HEATER INLET WATER HOSE
21. DISCONNECT HEATER OUTLET WATER HOSE
22. DISCONNECT FUEL HOSE NO.2
23. REMOVE AIR TUBE NO.2
(a) Loosen the 2 hose clamps, then disconnect the air hose
No. 3.
(b) Remove the 2 bolts and air tube No. 2.
24. SEPARATE TRANSMISSION CONTROL CABLE ASSY
(a) Remove the 2 clips, then separate the control cable assembly.
25. REMOVE INJECTOR DRIVER
(a) Remove the 2 nuts which secure the injector driver.
(b) Disconnect the injector driver connector and harness clamp.
(c) Remove the injector driver.
26. DISCONNECT ENGINE WIRE
(a) Remove the glove compartment door.
(b) Disconnect the engine wire from the ECM and junction
block.
(c) Pull out the engine wire.
(d) Disconnect the engine wire from the engine room junction
block.
(e) Remove the bolt, then disconnect the wire harness from
the body.

A87967
Upward90_
Clamp
Bolt
Turbocharger Side:
Air Hose No. 2 Side:
Front 90
_ Clamp Bolt
20.4_
14
−134
−
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1CD −FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
(b) Tighten the 2 hose clamps as shown in the illustration. Torque: 6.0 N
m (61 kgf
cm, 53 in.
lbf)
(c) Install the air tube No. 1 with the 3 bolts and nut. Torque: 25 N
m (255 kgf
cm, 18 ft
lbf)
208. INSTALL DIFFERENTIAL PRESSURE SENSOR ASSY Torque: 5.5 N
m (56 kgf
cm, 49 in.
lbf)
209. INSTALL RADIATOR ASSY (W/ AIR CONDITIONING) (See Pub. No. RM1018E on page 16 −51)
210. INSTALL ENGINE ROOM RELAY BLOCK NO.3
Torque: 5.3 N
m (54 kgf
cm, 47 in.
lbf)
211. INSTALL FUEL FILTER ASSY (See Pub. No. RM1018E on page 11 −82)
212. INSTALL AIR CLEANER ASSY Torque: 7.0 N
m (71 kgf
cm, 62 in.
lbf)
213. INSTALL BATTERY Torque:
5.0 N
m (51 kgf
cm, 44 in.
lbf) for bolt
3.0 to 4.0 N
m (31 to 41 kgf
cm, 27 to 35 in.
lbf) for nut
5.4 N
m (55 kgf
cm, 48 in.
lbf) for terminal
214. INSTALL ENGINE COVER SUB −ASSY NO.1
Torque: 8.0 N
m (82 kgf
cm, 71 in.
lbf)
215. BLEED CLUTCH PIPE LINE (See Pub. No. RM1018E on page 42 −12)
216. INSTALL FRONT WHEELS
Torque: 103 N
m (1,050 kgf
cm, 76 ft
lbf)
217. ADD MANUAL TRANSAXLE OIL (See Pub. No. RM1018E on page 41 −5)
218. ADD ENGINE OIL (See Pub. No. RM1018E on page 17 −30)
219. ADD ENGINE COOLANT (See page 16 −19)
220. CHECK CLUTCH FLUID LEAKAGE
221. CHECK FLUID LEVEL IN RESERVOIR
222. CHECK BRAKE FLUID LEAKAGE
223. CHECK FOR ENGINE OIL LEAKS
224. CHECK FOR FUEL LEAKS (See page 11 −46)
225. CHECK FOR ENGINE COOLANT LEAKS (See page 16 −15)
226. CHECK FOR EXHAUST GAS LEAKS
227. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (See Pub. No. RM1018E on page 26 −6)

141NE−01
A93837
To
Turbocharger
Air Hose No. 2
A93406
SST
14 −90−
ENGINE MECHANICAL VALVE CLEARANCE (1CD−FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
VALVE CLEARANCE (1CD −FTV)(From September, 2003)
ADJUSTMENT
NOTICE:
S Before removing the injection pipes, clean them up with a soft brush and compressed air.
S After removing the injection pipes, cover the supply pump, common rail and injector mounting
area of the cylinder head cover with vinyl tape to prevent dust from being introduced.
S After removing the cylinder head cover, protect the injector inlet with a vinyl or plastic bag to
prevent foreign objects from being introduced.
HINT:
Inspect and adjust the valve clearance after the engine becomes cold.
1. REMOVE RADIATOR SUPPORT OPENING COVER
2. REMOVE FRONT WHEEL RH
3. REMOVE ENGINE UNDER COVER LH
4. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
5. REMOVE ENGINE UNDER COVER RH
6. REMOVE ENGINE COVER SUB −ASSY NO.1
(a) Remove the 5 nuts, then remove the engine cover.
7. REMOVE BATTERY
8. REMOVE AIR TUBE NO.1
(a) Disconnect the vacuum hoses and connectors.
(b) Loosen the 2 hose clamps.
(c) Remove the 3 bolts and nut, then detach the air tube No.1.
9. REMOVE TIMING BELT NO.2 COVER (See page 14 −138)
10. REMOVE FUEL PIPE NO.3 (See page 14 −108)
SST 09023 −12700
11. REMOVE INJECTION PIPE SUB −ASSY NO.1
(a) Remove the 2 upper injection pipe clamps from the intake
manifold.
(b) Using SST, remove the injection pipe from the common
rail side.
SST 09023 −12700
(c) Using SST, remove the injection pipe from the injector
side.
SST 09023 −12700
(d) After removing the fuel pipe, in order to prevent dust or foreign objects from being introduced, cover the common
rail with vinyl tape and protect the injector inlet with a vinyl
or plastic bag.

141NC−01
Cut Position
A13332
A77419
SST
−
ENGINE MECHANICAL TIMING GEAR CASE OR TIMING CHAIN CASE OIL
SEAL (2AZ−FSE)14 −85
AVENSIS Supplement (RM1045E)
TIMING GEAR CASE OR TIMING CHAIN CASE OIL
SEAL (2AZ −FSE)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE RADIATOR SUPPORT OPENING COVER (See page 14 −23)
3. REMOVE ENGINE ROOM COVER SIDE (See page 14 −23)
4. REMOVE ENGINE UNDER COVER LH (See page 14 −23)
5. REMOVE ENGINE UNDER COVER NO.4 RH (See page 14 −23)
6. REMOVE ENGINE UNDER COVER RH (See page 14 −23)
7. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −45)
8. REMOVE FAN AND GENERATOR V BELT (See page 14 −5)
SST 09249 −63010
9. REMOVE CRANKSHAFT PULLEY (See page 14 −45)
SST 09213 −54015 (91651 −60855), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05021)
10. REM O VE TI M I NG G EAR CASE O R T I M I NG CHAI NCASE OIL SEAL
(a) Using a screwdriver with tip wrapped in the tape, pry out the oil seal.
HINT:
After removal, check that the crankshaft is not damaged.
If damaged, smooth the surface with 400 −grit sandpaper.
11. I NSTALL TI M I NG G EAR CASE O R T I M I NG CHAI N CASE OIL SEAL
(a) Apply MP grease to a new oil seal lip.
NOTICE:
Keep the lip off foreign materials.
(b) Using SST and a hammer, tap in the oil seal until its sur- face is flush with the rear oil seal retainer edge.
SST 09223 −22010
NOTICE:
Wipe off extra grease on the crankshaft.
12. INSTALL CRANKSHAFT PULLEY (See page 14 −45)
SST 09213 −54015 (91651 −60855), 09330 −00021
13. INSTALL FAN AND GENERATOR V BELT (See page 14 −5)
SST 09249 −63010
14. INSTALL ENGINE COVER SUB −ASSY NO.1
Torque: 7.0 N
m (71 kgf
cm, 62 in.
lbf)
15. INSTALL FRONT WHEEL RH Torque: 103 N
m (1,050 kgf
cm, 76 ft
lbf)
16. CHECK FOR ENGINE OIL LEAKS

141NB−01
−
ENGINE MECHANICAL CYLINDER HEAD GASKET (2AZ −FSE)
14 −79
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. DISCHARGE FUEL SYSTEM PRESSURE (See page 11 −4)
2. REMOVE FRONT WHEEL RH
3. REMOVE RADIATOR SUPPORT OPENING COVER (See page 14 −23)
4. REMOVE ENGINE ROOM COVER SIDE (See page 14 −23)
5. REMOVE ENGINE UNDER COVER LH (See page 14 −23)
6. REMOVE ENGINE UNDER COVER NO.4 RH (See page 14 −23)
7. REMOVE ENGINE UNDER COVER RH (See page 14 −23)
8. DRAIN COOLANT (See page 16 −7)
9. DRAIN ENGINE OIL (See page 17 −6)
10. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −45)
11. REMOVE FUEL PRESSURE PULSATION DAMPER ASSY
12. SEPARATE FUEL TUBE SUB −ASSY (See page 11 −4)
13. REMOVE FUEL PIPE SUB −ASSY NO.1 (See page 11 −24)
SST 09023 −12900
14. REMOVE FUEL PUMP ASSY (See page 11 −24)
15. REMOVE FAN AND GENERATOR V BELT (See page 14 −5)
SST 09249 −63010
16. REMOVE GENERATOR ASSY (See page 19 −8)
17. REMOVE EXHAUST PIPE ASSY FRONT (See page 15 −2)
18. SEPARATE VANE PUMP ASSY (See page 14 −45)
19. REMOVE IGNITION COIL ASSY (See page 14 −45)
20. SEPARATE RETURN TUBE SUB −ASSY (See page 14 −45)
21. SEPARATE COOLER REFRIGERANT SUCTION HOSE NO.1 (LHD STEERING POSITION TYPE) (See page 14 −45)
22. REMOVE VANE PUMP OIL RESERVOIR ASSY (See page 14 −45)
23. REMOVE OIL RESERVOIR BRACKET NO.1 (See page 14 −45)
24. SEPARATE ENGINE WIRE (See page 14 −23)
25. REMOVE COOLER BRACKET (LHD STEERING POSITION TYPE) (See page 14 −45)
26. REMOVE ENGINE SERVICE COVER BRACKET RH (RHD STEERING POSITION TYPE)
(See page 14 −45)
27. REMOVE CYLINDER HEAD COVER SUB −ASSY (See page 14 −45)
28. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −45)
29. REMOVE ENGINE MOUNTING BRACKET NO.2 RH (See page 14 −45)
30. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (See page 14 −45)
31. REMOVE CRANKSHAFT PULLEY (See page 14 −45)
SST 09213 −54015 (91651 −60855), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05021)
32. REMOVE CHAIN TENSIONER ASSY NO.1 (See page 14 −45)
33. REMOVE CRANKSHAFT POSITION SENSOR (See page 14 −45)
34. REMOVE OIL PAN SUB −ASSY (See page 14 −45)
SST 09032 −00100
35. REMOVE V −RIBBED BELT TENSIONER ASSY (See page 14 −45)
36. REMOVE TIMING CHAIN OR BELT COVER SUB −ASSY (See page 14 −45)
37. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO.1 (See page 14 −45)
38. REMOVE CHAIN TENSIONER SLIPPER (See page 14 −45)
39. REMOVE CHAIN VIBRATION DAMPER NO.1 (See page 14 −45)
40. REMOVE TIMING CHAIN GUIDE (See page 14 −45)
41. REMOVE CHAIN SUB −ASSY (See page 14 −45)

A32664
A56213
Wooden Block
A83481
14−80
−
ENGINE MECHANICAL CYLINDER HEAD GASKET (2AZ −FSE)
AVENSIS Supplement (RM1045E)
42. REMOVE BATTERY (See page 14 −45)
43. REMOVE AIR CLEANER ASSEMBLY WITH HOSE (See page 14 −23)
44. DISCONNECT RADIATOR HOSE INLET (See page 14 −23)
45. DISCONNECT UNION TO CONNECTOR TUBE HOSE (See page 14 −23)
46. DISCONNECT HEATER INLET WATER HOSE (See page 14 −23)
47. SEPARATE FUEL TUBE SUB −ASSY (See page 11 −1)
48. SEPARATE ENGINE WIRE
49. REMOVE THROTTLE BODY ASSY (See page 10 −8)
50. REMOVE CHARCOAL CANISTER ASSY
51. REMOVE INTAKE MANIFOLD (See page 11 −13)
52. REMOVE MANIFOLD CONVERTER INSULATOR NO.1 (See page 14 −23)
53. REMOVE EXHAUST MANIFOLD CONVERTER SUB −ASSY (See page 14 −23)
54. REMOVE NO.2 CAMSHAFT (See page 14 −64)
55. REMOVE CAMSHAFT (See page 14 −64)
56. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSY (See page 14 −23)
57. REMOVE CAMSHAFT BEARING NO.2
58. SUPPORT ENGINE ASSEMBLY WITH TRANSAXLE
(a) Install the oil pan sub −assy.
(b) Set the jack under the engine assembly with transaxle,
then place a wooden block on the jack.
(c) Remove the chain block and sling devise.
59. REMOVE CYLINDER HEAD SUB −ASSY
(a) Remove the bolt, then separate the water by −pass pipe.
(b) Remove the camshaft housing plug.