2005 TOYOTA AVENSIS radiator

11−20
−
FUEL FUEL INJECTOR ASSY (2AZ −FSE)
AVENSIS Supplement (RM1045E)
36. ADD ENGINE COOLANT (see page 16 −7)
37. CHECK FOR ENGINE COOLANT LEAKS (See page 16 −1)
38. CHECK FOR FUEL LEAKS (See page 11 −4)
39. CHECK FOR ENGINE OIL LEAKS
40. INSTALL ENGINE COVER SUB −ASSY NO.1 (See page 10 −8)
41. INSTALL ENGINE ROOM COVER SIDE
42. INSTALL RADIATOR SUPPORT OPENING COVER

100FO−02
A80092
(b)(a)
(a)
(b)
A85751
A64328
2to7mm0to4mm
(0.08 to 0.28
in.)(0 to 0.16
in.)
− ENGINE CONTROL SYSTEMINTAKE SHUTTER ASSY (1CD−FTV)(From September,
2003)10−27
AVENSIS Supplement (RM1045E)
Removal & Installation and Disassembly & Reassembly
1. REMOVE RADIATOR SUPPORT OPENING COVER
2. REMOVE ENGINE COVER SUB−ASSY NO.1
(a) Remove the 5 nuts and engine cover.
3. REMOVE BATTERY
4. REMOVE AIR HOSE NO.4
(a) Loosen the 2 hose clamps.
(b) Remove the 2 bolts, then separate the air tube No. 2.
(c) Remove the air hose No. 4.
5. REMOVE INTAKE SHUTTER ASSY
(a) Disconnect the 2 connectors.
(b) Remove the 3 nuts, then remove the intake shutter and
gasket.
6. INSTALL INTAKE SHUTTER ASSY
(a) Install a new gasket and the intake shutter with the 3 nuts.
Torque: 21 N
m (209 kgf
cm, 15 ft
lbf)
7. INSTALL AIR HOSE NO.4
(a) Install the air hose No. 4 to the air tube No. 2.
(b) Install the air tube No. 2 with the 2 bolts.
Torque: 25 N
m (255 kgf
cm, 18 ft
lbf)
(c) Install the air hose and hose clamps as shown in the il-
lustration.

100LZ−01
A88269
(a)
(b)
A78436
10 _
10 _ Upper
Engine
Front
10
−16
−
ENGINE CONTROL SYSTEM KNOCK SENSOR (2AZ−FSE)
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. DISCHARGE FUEL SYSTEM PRESSURE (See page 11 −1)
2. REMOVE RADIATOR SUPPORT OPENING COVER (See page 10 −8)
3. REMOVE ENGINE ROOM COVER SIDE (See page 10 −8)
4. DISCONNECT ENGINE WIRE NO.3 (BATTERY NEGATIVE TERMINAL)
5. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 10 −8)
6. DRAIN ENGINE COOLANT (See page 16 −7)
7. REMOVE AIR CLEANER CAP SUB −ASSY (See page 10 −8)
8. REMOVE THROTTLE BODY ASSY (See page 10 −8)
9. REMOVE FUEL TUBE SUB −ASSY (See page 11 −24)
SST 09617 −24011
10. REMOVE FUEL HOSE (See page 11 −24)
11. REMOVE FUEL PIPE SUB −ASSY NO.1 (See page 11 −24)
SST 09023 −12900
12. REMOVE FUEL PUMP ASSY (See page 11 −24)
13. REMOVE CHARCOAL CANISTER ASSY (See page 11 −13)
14. REMOVE VACUUM SENSOR ASSY (LHD STEERING POSITION TYPE) (See page 11 −13)
15. REMOVE INTAKE MANIFOLD (See page 11 −4)
16. REMOVE SURGE TANK STAY NO.1 (See page 11 −13)
17. REMOVE INTAKE MANIFOLD INSULATOR NO.2 (See page 11 −13)
18. REMOVE KNOCK SENSOR
(a) Disconnect the knock sensor connector.
(b) Remove the nut, then remove the knock sensor.
19. INSTALL KNOCK SENSOR
(a) Install the knock sensor with the nut as shown in the il- lustration.
Torque: 20 N
m (204 kgf
cm, 15 ft
lbf)
(b) Connect the knock sensor connector.
20. INSTALL INTAKE MANIFOLD INSULATOR NO.2
21. INSTALL SURGE TANK STAY NO.1 ( See page 11 −13)
22. INSTALL INTAKE MANIFOLD (See page 11 −13)
23. INSTALL VACUUM SENSOR ASSY (LHD STEERING POSITION TYPE) (See page 11 −13)
24. INSTALL CHARCOAL CANISTER ASSY

−
ENGINE CONTROL SYSTEM KNOCK SENSOR (2AZ−FSE)
10 −17
AVENSIS Supplement (RM1045E)
25. INSTALL FUEL PUMP ASSY (See page 11 −24)
26. INSTALL FUEL PIPE SUB −ASSY NO.1 (See page 11 −24)
SST 09023 −12900
27. INSTALL FUEL HOSE
28. INSTALL FUEL TUBE SUB −ASSY (See page 11 −24)
SST 09617 −24011
29. INSTALL THROTTLE BODY ASSY (See page 10 −8)
30. INSTALL AIR CLEANER CAP SUB −ASSY (See page 10 −8)
31. CONNECT ENGINE WIRE NO.3 (BATTERY NEGATIVE TERMINAL) Torque: 5.4 N
m (55 kgf
cm, 48 in.
lbf)
32. ADD ENGINE COOLANT (See page 16 −7)
33. CHECK FOR ENGINE COOLANT LEAKS (See page 16 −1)
34. CHECK FOR FUEL LEAKS (See page 11 −4)
35. CHECK FOR ENGINE OIL LEAKS
36. INSTALL ENGINE COVER SUB −ASSY NO.1 ( See page 10 −8)
37. INSTALL ENGINE ROOM COVER SIDE
38. INSTALL RADIATOR SUPPORT OPENING COVER

141NM−01
14 −166−
ENGINE MECHANICAL CYLINDER HEAD GASKET (1CD −FTV)(From
September, 2003)
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE ENGINE UNDER COVER LH
3. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
4. REMOVE ENGINE UNDER COVER RH
5. REMOVE RADIATOR SUPPORT OPENING COVER
6. REMOVE ENGINE ROOM COVER SIDE
7. DRAIN ENGINE COOLANT (See page 16 −19)
8. DRAIN ENGINE OIL (See Pub. No. RM1018E on page 17 −30)
9. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −90)
10. REMOVE VACUUM RESERVOIR SUB −ASSY (See page 14 −108)
11. REMOVE AIR CLEANER ASSY (See page 14 −108)
12. REMOVE BATTERY
13. REMOVE AIR TUBE NO.2 (See page 14 −108)
14. REMOVE AIR TUBE NO.1 (See page 14 −108)
15. REMOVE INJECTOR DRIVER (See page 14 −108)
16. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See Pub. No. RM1018E on page 14 −269)
17. REMOVE GENERATOR V BELT (See Pub. No. RM1018E on page 14 −269)
18. SEPARATE POWER STEERING IDLE PULLEY BRACKET (See page 14 −138)
19. DISCONNECT ENGINE WIRE (See page 14 −138)
20. DISCONNECT VACUUM HOSE (See page 14 −108)
21. REMOVE DIFFERENTIAL PRESSURE SENSOR ASSY(See page 14 −108)
22. REMOVE ENGINE MOUNTING INSULATOR SUB −ASSY RH (See page 14 −138)
23. REMOVE CRANKSHAFT PULLEY (See page 14 −138)
SST 09213 −54015 (09213 −70020), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05031)
24. REMOVE IDLER PULLEY SUB −ASSY (See page 14 −138)
25. REMOVE TIMING BELT NO.2 COVER (See page 14 −138)
26. REMOVE TIMING BELT NO.1 COVER (See page 14 −138)
27. REMOVE TIMING BELT GUIDE
28. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (See page 14 −138)
29. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −138)
30. REMOVE TIMING CHAIN COVER PLATE (See page 14 −138)
31. REMOVE TIMING BELT (See page 14 −138)
HINT:
If reusing the timing belt, draw an arrow on the timing belt which indicates the engine revolution direction
and put match marks on the pulleys and timing belt.
32. REMOVE FUEL FILTER ASSY (See Pub. No. RM1018E on page 11 −82)
33. REMOVE HEATER PUMP ASSY (W/ COLD AREA) (See page 13 −12)
34. REMOVE HEATER BRACKET (W/ COLD AREA) (See page 13 −12)
35. REMOVE FLOOR PANEL BRACE FRONT (See page 15 −6)
36. REMOVE EXHAUST PIPE ASSY FRONT (See page 15 −6)
37. REMOVE EXHAUST PIPE ASSY (W/ COLD AREA) (See page 13 −12)
38. DISCONNECT RADIATOR HOSE INLET
39. DISCONNECT HEATER INLET WATER HOSE
40. DISCONNECT HEATER OUTLET WATER HOSE
41. DISCONNECT FUEL PIPE TO FUEL TUBE FUEL HOSE
42. DISCONNECT OIL COOLER HOSE

141NK−01
SSTA61187
−
ENGINE MECHANICAL CAMSHAFT (1CD−FTV)(From September, 2003)
14 −151
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE ENGINE UNDER COVER LH
3. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
4. REMOVE ENGINE UNDER COVER RH
5. REMOVE RADIATOR SUPPORT OPENING COVER
6. REMOVE ENGINE ROOM COVER SIDE
7. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −90)
8. REMOVE AIR CLEANER ASSY (See page 14 −108)
9. REMOVE BATTERY
10. REMOVE VACUUM RESERVOIR SUB −ASSY (See page 14 −108)
11. REMOVE AIR TUBE NO.1 (See page 14 −108)
12. REMOVE INJECTOR DRIVER (See page 14 −108)
13. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM1018E on page 14 −269)
14. REMOVE GENERATOR V BELT (See Pub. No. RM1018E on page 14 −269)
15. SEPARATE POWER STEERING IDLE PULLEY BRACKET (See page 14 −138)
16. DISCONNECT ENGINE WIRE (See page 14 −138)
17. DISCONNECT VACUUM HOSE (See page 14 −108)
18. REMOVE ENGINE MOUNTING INSULATOR SUB −ASSY RH (See page 14 −138)
19. REMOVE CRANKSHAFT PULLEY (See page 14 −138)
SST 09213 −54015 (09213 −70020), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05031)
20. REMOVE IDLER PULLEY SUB −ASSY (See page 14 −138)
21. REMOVE TIMING BELT NO.2 COVER (See page 14 −138)
22. REMOVE TIMING BELT NO.1 COVER (See page 14 −138)
23. REMOVE TIMING BELT GUIDE
24. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (See page 14 −138)
25. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −138)
26. REMOVE TIMING CHAIN COVER PLATE (See page 14 −138)
27. REMOVE TIMING BELT (See page 14 −138)
28. REMOVE CAMSHAFT POSITION SENSOR (See page 14 −108)
29. REMOVE CAMSHAFT TIMING PULLEY
(a) Using SST, remove the pulley bolt. SST 09960 −10010 (09962 −01000, 09963 −01000)
(b) Remove the timing pulley.
HINT:
Using a plastic −faced hammer, tap out the pulley.
(c) Remove the set key.
30. REMOVE FUEL PIPE NO.3 (See page 14 −108)
SST 09023 −12700

141NJ−01
A85615
Engine Cover Sub−assy No. 1
Radiator Support Opening Cover
Clip
Clip
Retainer
8.0 (82, 71 in.
lbf)
w/ A/C:
V (Cooler
Compressor to
Crankshaft
Pulley) Belt No. 1
72 (734, 53)
39 (398, 29)
Power Steering
Idle Pulley
Bracket
Clip
N·m (kgf·cm, ft·lbf)
: Specified torque Engine Under
Cover RH
Engine Under
Cover Sub−assy No. 1
Clip
Engine Under Cover LH
Clip
Air Cleaner Cap w/ Hose
Air Cleaner Element
Air Cleaner Case
7.0 (71, 62 in.
lbf)
Mass Air Flow
Meter Connector
Engine Wire Vacuum Hose
14−146
− ENGINE MECHANICALCAMSHAFT (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
CAMSHAFT (1CD−FTV)(From September, 2003)
COMPONENTS

141NI−01
A61175
A84394
A61184
14 −138
−
ENGINE MECHANICAL TIMING BELT (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
3. REMOVE ENGINE UNDER COVER RH
4. REMOVE RADIATOR SUPPORT OPENING COVER
5. REMOVE ENGINE ROOM COVER SIDE
6. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −90)
7. REMOVE INJECTOR DRIVER (See page 14 −108)
8. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM1018E on page 14 −269)
9. REMOVE GENERATOR V BELT (See Pub. No. RM1018E on page 14 −269)
10. SEPARATE PO W ER STEERI NG I DLE PULLEY BRACKET
(a) Remove the 3 bolts and power steering idle pulley brack- et.
11. DISCONNECT ENGINE WIRE
(a) Disconnect the 2 exhaust gas temperature sensor con- nectors.
12. DISCONNECT VACUUM HOSE (See page 14 −108)
13. REMOVE ENGINE MOUNTING INSULATOR SUB−ASSY RH
(a) Place a wooden block on a jack underneath the engine.