2005 TOYOTA AVENSIS Actuator

±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
05±301
AVENSIS REPAIR MANUAL (RM1018E)DTC No.
Fail±Safe Deactivation Conditions
Fail±Safe Operation
P2102
P2103
P2111
P2112
P2118
P2119
Turn off the power for the throttle motor, return the throttle
valve in position using the return spring, and fuel cut inter-
mittent.After it is returned to normal condition, turn the ignition switch
ON.
P2120
P2121
P2122
P2123
P2125
P2127
P2128
P2138

If both VPA1 and VPA2 are malfunctioning:
Fixed at idle

If either of VPA1 or VPA2 is malfunctioning:
Fuel cut intermittently
After it is returned to normal condition, turn the ignition switch
ON.
5.CHECK FOR INTERMITTENT PROBLEMS
Hand±held tester only:
By putting the vehicle's ECM in the check mode, the 1 trip detection logic is possible instead \
of the 2 trip
detection logic, and the sensitivity to detect faults is increased. This\
makes it easier to detect intermittent
problems.
(a)Clear the DTCs (See step 2).
(b)Set the check mode (See step 3).
(c)Perform a simulation test (See page 01±22).
(d)Check the connector and terminal (See page 01±32).
(e)Wiggle the harness and the connector (See page 01±32).
6. DATA LIST
HINT:
Using the DATA LIST displayed by the hand±held tester, you can read the value of the switches, sensors,
actuators and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting is one
method to shorten diagnostic time.
NOTICE:
The values given below for ºNormal Conditionº are representative valu\
es. A vehicle may still be nor-
mal even if its value differs from those listed here. So, do not solely dep\
end on the ºNormal Condi-
tionº here when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch ON.
(e) Push the ºONº button of the hand±held tester.
(f) Select the item ºDIAGNOSIS / OBD/MOBD / DATA LISTº.
(g) According to the display on tester, read the ºDATA LISTº.
Hand±held Tester DisplayMeasurement Item/Range
(Display)Normal Condition *1Diagnostic Note
INJECTOR
Injection period of the No. 1 cylin-
der/
Min.: 0 ms, Max.: 32.64 ms
Idling: 0.40 to 0.78 ms

IGN ADVANCE
Ignition timing advance for No. 1
cylinder/
Min.: ±64 deg., Max.: 63.5 deg.
Idling: BTDC 5 to 23


CALC LOADCalculated load by ECM/
Min.: 0 %, Max.: 100 %
Idling: 21.6 to 31.4 %

Running without load (2,500
rpm): 19.6 to 29.4 %

05±306
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
7. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one method
to shorten diagnostic time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch ON.
(e) Push the ºONº button of the hand±held tester.
(f) Select the item ºDIAGNOSIS / OBD/MOBD / ACTIVE TESTº
(g) According to the display on tester, perform the ºACTIVE TESTº.
Hand±held Tester DisplayTest DetailsDiagnostic Note
INJ VOL
[Test Details]
Control the injection volume
Min.: ±12.5 %, Max.: 25 %
[Vehicle Condition]
Engine speed: 3,000 rpm or less
All injectors are tested at once.

Injection volume is gradually
changed between ±12.5 and 25
%.
A/F CONTROL
[Test Details]
Control the injection volume
±12.5 or 25 % (Change the injection volume ±12.5 % or 25 %.)
[Vehicle Condition]
Engine speed: 3,000 rpm or less
The following procedure of A/F
CONTROL enables the user to
check its output (show its graph
indication) of sensor 1 and sensor
2:
For displaying the graph indication,
enter ºACTIVE TEST / A/F CON-
TROL / USER DATAº, then select
ºO2S B1 S1 and O2S B1 S2º by
pressing ºYESº button and push
ºENTERº button before pressing
ºF4º button.
SCV VSV
[Test Details]
Activate the VSV for intake air control valve.
ON or OFF


EVAP VSV (ALONE)
[Test Details]
Activate the VSV for EVAP control
ON or OFF


FUEL PUMP / SPD
[Test Details]
Control the fuel pump
ON or OFF


VVT CTRL B1
[Test Details]
Active the VVT system (Bank 1).
ON or OFF
ON: Rough idle or engine stall.

OFF: Normal engine speed.
TC/TE1
[Test Details]
Connect the TC and TE1
ON or OFF


FC IDL PROHBT
[Test Details]
Control the idle fuel cut prohibit
ON or OFF

A71007
Air Flow Meter Crankshaft Position Sensor
Actual Valve TimingCorrection Target Valve Timing
Feedback
Duty Control ECM
Camshaft Timing
Oil Control
Valve (OCV)
Vehicle Speed Signal Engine Coolant Temp. SensorThrottle Position Sensor
Camshaft Position Sensor
05±322
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
DTC P0010 CAMSHAFT POSITION ºAº ACTUATOR
CIRCUIT (BANK 1)
HINT:
This is the procedure of oil control valve (OCV).
CIRCUIT DESCRIPTION
The VVT system controls the intake camshaft to provide the optimal valve timing for every driving condition. This control
is performed based on the signals, such conditions as intake air volume, throttle position and engine coolant tempera-
ture.
The ECM controls the oil control valve (OCV), based on the signals output from the sensors. The VVT controller regu-
lates the intake camshaft angle using oil pressure through the OCV. As result, the relative position between the camshaft
and the crankshaft becomes optimal, and the engine torque improves, fuel economy improves, exhaust emissions de-
crease under overall driving conditions. Also, the ECM detects the actual valve timing using the signals from the cam-
shaft position sensor and the crankshaft position sensor, and performs feedback control. This is how target valve timing
is achieved by the ECM.
DTC No.DTC Detection ConditionTrouble Area
P0010Open or short in OCV circuit

Open or short in OCV circuit

OCV

ECM
05CDY±01

05±470
±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
DTCP0604INTERNAL CONTROL MODULE RANDOM ACCESS MEMORY (RAM) ERROR
DTCP0606ECM/PCM PROCESSOR
DTCP0607CONTROL MODULE PERFORMANCE
DTCP0657ACTUATOR SUPPLY VOLTAGE CIRCUIT/OPEN
CIRCUIT DESCRIPTION
DTC No.DTC Detection ConditionTrouble Area
P0604
P0606
P0607
P0657
ECM inside error
ECM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions when
a malfunction is detected, when troubleshooting it is useful for determi\
ning whether the vehicle was running
or stopped, the engine warmed up or not, the air±fuel ratio lean or ric\
h, etc. at the time of the malfunction.
REPAIR OR REPLACE ECM (See page 01±32)
05CJA±01

05±490
±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
DTCP2119THROTTLE ACTUATOR CONTROL THROTTLE BODY RANGE/PERFORMANCE
CIRCUIT DESCRIPTION
The Electric Throttle Control System (ETCS) is composed of the throttle m\
otor that operates the throttle
valve, the throttle position sensor that detects the opening angle of the throttle valve, the accelerator pedal
position sensor that detects the accelerator pedal position, the ECM that contro\
ls the ETCS, and the one
valve type throttle body.
The ECM controls the throttle motor to provide the proper throttle valve\
opening angle in response to the
driving condition.
The throttle position sensor which is mounted on the throttle body detects \
the opening angle of the throttle
valve, and it provides feedback to the ECM to control the throttle motor.
If the ETCS has a malfunction, the ECM shuts down the power for the throttle motor, and the throttle valve
is closed by the return spring. And the throttle valve is locked at a ce\
rtain opening angle. Also, the whole
electronically controlled throttle operation is cancelled until the system returns to normal and the ignition
switch is turned OFF.
DTC No.DTC Detection ConditionTrouble Area
P2119Throttle opening angle continues to vary greatly from target
throttle opening angle
Electric throttle control system

ECM
WIRING DIAGRAM
Refer to DTC P2102 on page 05±483.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, it is useful for determi\
ning whether the vehicle was running
or stopped, the engine was warmed up or not, the air±fuel ratio was lea\
n or rich, etc. at the time of the mal-
function.
1CHECK OTHER DTC OUTPUT(IN ADDITION TO DTC P2119)
(a)Read the DTC using hand±held tester.
Result:
Display (DTC output)Proceed to
Only P2119 is outputA
P2119 and other DTCs are outputB
HINT:
If any other codes besides P2119 are output, perform the troubleshooting for those DTCs first.
BGO TO RELEVANT DTC CHART (See page 05±309)
A
05CKS±01

A76877
ECM
+BM
FL MAINTHROTTLE Engine Room J/B No. 1 and
Engine Room R/B No. 1
E10
IE2 1A 4B15
2 Engine Room J/B No. 4
6
B±G
Battery4A1
B±G
1 1
1G±R G±Y
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±487
AVENSIS REPAIR MANUAL (RM1018E)
DTC P2118 THROTTLE ACTUATOR CONTROL MOTOR
CURRENT RANGE/PERFORMANCE
CIRCUIT DESCRIPTION
If this DTC is detected, the ECM shuts down the power for the throttle motor, and the throttle valve is closed
by the return spring. And the throttle valve is locked at a certain opening angle. Also, the whole electronically
controlled throttle operation is cancelled until the system returns to normal and the ignition switch is turned
OFF.
HINT:
This electrical throttle control system (ETCS) does not use the throttle cable.
DTC No.DTC Detection ConditionTrouble Area
P2118Open in ETCS power source circuit
Open in ETCS power source circuit

ECM
WIRING DIAGRAM
05CKR±01

A54292
T1
Throttle Control Motor
(Built in Throttle Body)
2
1B
WECM
3
2
17M+
M±
E11
(Shielded)
E11
E11
GE01
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±483
AVENSIS REPAIR MANUAL (RM1018E)
DTC P2102 THROTTLE ACTUATOR CONTROL MOTOR
CIRCUIT LOW
DTC P2103 THROTTLE ACTUATOR CONTROL MOTOR
CIRCUIT HIGH
CIRCUIT DESCRIPTION
The throttle motor is operated by the ECM and it opens and closes the throttle valve.
The opening angle of the throttle valve is detected by the throttle position sensor which is mounted on the
throttle body. It provides feedback to the ECM to control the throttle motor in order to regulate the throttle
valve opening angle properly in response to the driving condition.
If this malfunction is detected, the ECM shuts down the power for the throttle motor, and the throttle valve
is closed by the return spring. And the throttle valve is locked at a certain opening angle. Also, the whole
electronically controlled throttle operation is cancelled until the system returns to normal and the ignition
switch is turned OFF.
HINT:
This electrical throttle system does not use the throttle cable.
DTC No.DTC Detection ConditionTrouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds:
(a) Throttle control motor output duty greater than 80 %
(b) Throttle control motor current less than 0.5 A
Open in throttle control motor circuit

Throttle control motor

ECM
Throttle control motor current greater than 10 A
Short in throttle control motor circuit
P2103Condition (a) continues for 0.6 seconds:
(a) Throttle control motor current greater than 7 A
Short in throttle control motor circuit

Throttle control motor

ECM
WIRING DIAGRAM
05CKP±01

A76875
ECM
SCV 5
E13 EFI Relay
1 1 23
Engine Room
J/B No. 4B±W
1MREL 8
E9
Battery FL MAIN B±G2 5
GR
V6
VSV (Intake Air Control Valve)
2
L±B EFI No. 2 1
B±G
W±B
ECW±B
4A
14B11AEFI
1B±Y
1
2 4
4
44
4
4
B±W Engine Room
R/B No. 1
and
Engine Room
J/B No. 1Engine Room R/B No. 4
GR
B±W
EA113IE1 2 05±480
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
DTC P2008 INTAKE MANIFOLD RUNNER CONTROL
CIRCUIT / OPEN (BANK 1)
CIRCUIT DESCRIPTION
The Intake Air Control valve (IACV) is opened and shut by the actuator with intake manifold vacuum.
It stabilizes the engine combustion. The IACV operation generates swirl air flow in the cylinder.
DTC No.DTC Detection ConditionTrouble Area
P2008Open or short in VSV for IACV circuit 0.5 sec. or more
(2 trip detection logic)
Open of short in VSV for IACV circuit

VSV for IACV

ECM
WIRING DIAGRAM
05CK5±01