2005 TOYOTA AVENSIS sensor

05−566− DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U151E)
AVENSIS Supplement (RM1045E)
DTC P0705 TRANSMISSION RANGE SENSOR CIRCUIT
MALFUNCTION (PRNDL INPUT)
CIRCUIT DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.DTC Detection ConditionTrouble Area
P0705
(A) Any 2 or more signals of the following are ON simulta-
neously (2−trip detection logic)
SP input signal is ON.
SN input signal is ON.
SR input signal is ON.
SD input signal is ON.
(B) When any of following conditions is met for 2.0 sec. or
more in the S position (2−trip detection logic)
SP input signal is ON.
SN input signal is ON.
SR input signal is ON.
SOpen or short in park/neutral position switch circuit
SPark/neutral position switch
SECM
MONITOR DESCRIPTION
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started
only when the vehicle is in P or N shift position.
When the park/neutral position switch sends more than one signal at a time from switch positions P, R, N
or D, the ECM interprets this as a fault in the switch. The ECM will turn on the MIL and store the DTC.
05CVP−02

C91579
Switch Side:
(Connector Front View):
N1
05−568− DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U151E)
AVENSIS Supplement (RM1045E)
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the hand−held tester, you can read the value of the switch, sensor,
actuator and so on without parts removal. Reading the DATA LIST as the first step of troubleshooting is one
method to shorten labor time.
(a) Turn the ignition switch off.
(b) Connect the hand−held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Push the ”ON” button of the hand−held tester.
(e) Select the item ”DIAGNOSIS / OBD/MOBD / DATA LIST”.
(f) According to the display on tester, read the ”DATA LIST”.
ItemMeasurement Item/
Range (display)Normal ConditionDiagnostic Note
REVERSEPNP SW Status/
ON or OFFShift lever position is;
R: ON
Except R: OFF
When the shift lever position dis-
played on the hand−held tester dif-
fers from the actual position, ad-
justment of the PNP switch or the
shift cable may be incorrect.
DRIVEPNP SW Status/
ON or OFFShift lever position is;
D and S: ON
Except D and S: OFF


1INSPECT PARK/NEUTRAL POSITION SWITCH ASSY
(a) Disconnect the park/neutral position switch connector.
(b) Measure resistance according to the value(s) in the table
below when the shift lever is moved to each position.
Standard:
Shift PositionTester ConnectionSpecified Condition
P1−3 and 6−9Below1
Except P
10kor higher
R2−3Below1
Except R
10kor higher
N3−5 and 6−9Below1
Except N
10kor higher
D, S, ”+” and ”−”3−7Below1
Except D, S, ”+” and ”−”
10kor higher
NG REPLACE PARK/NEUTRAL POSITION SWITCH
ASSY
OK

056IK−05
05 −564−
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U 151E)
AVENSIS Supplement (RM 1045E)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the page
given.
HINT:
S *1 : F ... MIL (Malfunction Indicator Lamp) light up
S *2 : ’’ f ’’ mark means ECM memorizes the malfunction code if the ECM detects the DTC detection
condition.
S This DTC may be output when the clutch, brake and gear components etc. inside the automatic trans-
axle are damaged.
DTC No.
(See Page)Detection ItemTrouble AreaMIL *1Memory *2
P0500
(05 −1 83)Vehicle Speed Sensor ”A”
SCombination meter
S Open or short in vehicle speed sensor circuit
S Vehicle speed sensor
S ECM
Ff
P0705
(05 −566)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input)SOpen or short in park/neutral position switch circuit
S Park/neutral position switch
S ECM
Ff
P07 10
(05 −57 1)Transmission Fluid Temperature
Sensor ”A” CircuitS Open or short in ATF temperature sensor circuit
S Transmission wire (ATF temperature sensor)
S ECM
Ff
P07 11
(05 −574)Transmission Fluid Temperature
Sensor ”A” PerformanceSOpen or short in ATF temperature sensor circuit
S Transmission wire (ATF temperature sensor)
S ECM
Ff
P07 12
(05 −57 1)Transmission Fluid Temperature
Sensor ”A” Circuit Low InputS Short in ATF temperature sensor circuit
S Transmission wire (ATF temperature sensor)
S ECM
Ff
P07 13
(05 −57 1)Transmission Fluid Temperature
Sensor ”A” Circuit High InputS Open in ATF temperature sensor circuit
S Transmission wire (ATF temperature sensor)
S ECM
Ff
P07 17
(05 −577)Turbine Speed Sensor Circuit No
Signal
SOpen or short in transmission revolution sensor NT (speed
sensor NT) circuit
S Transmission revolution sensor NT (speed sensor NT)
S ECM
S Automatic transaxle assembly
Ff
P0724
(05 −580)Brake Switch ”B” Circuit High
SShort in stop light switch circuit
S Stop light switch
S ECM
Ff
P074 1
(05 −582)Torque Converter Clutch Sole-
noid Performance
(Shift Solenoid Valve DSL)
S Shift solenoid valve DSL remains open or closed
S Valve body is blocked
S Shift solenoid valve DSL
S Torque converter clutch
S Automatic transaxle (clutch, brake or gear etc.)
S Line pressure is too low
S ECM
Ff
P0743
(05 −586)Torque Converter Clutch Circuit
Electrical
(Shift Solenoid Valve DSL)SOpen or short in shift solenoid valve DSL circuit
S Shift solenoid valve DSL
S ECM
Ff
P0746
(05 −589)Pressure Control Solenoid ”A”
Performance
(Shift Solenoid Valve SL 1)
SShift solenoid valve SL 1remains open or closed
S Valve body is blocked
S Shift solenoid valve SL 1
S Automatic transaxle (clutch, brake or gear etc.)
S ECM
Ff

−
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U 151E)05 −565
AVENSIS Supplement (RM 1045E)
P0748
(05 −592)
Pressure Control Solenoid ”A”
Electrical
(Shift Solenoid Valve SL 1)SOpen or short in shift solenoid valve SL 1circuit
S Shift solenoid valve SL 1
S ECM
Ff
P0766
(05 −595)Shift Solenoid ”D” Performance
(Shift Solenoid Valve S4)
SShift solenoid valve S4 remains open or closed
S Valve body is blocked
S Shift solenoid valve S4
S Automatic transaxle (clutch, brake or gear etc.)
S ECM
Ff
P077 1
(05 −598)Shift Solenoid ”E” Performance
(Shift Solenoid Valve SR)
SShift solenoid valve SR remains open or closed
S Valve body is blocked
S Shift solenoid valve SR
S Automatic transaxle (clutch, brake or gear etc.)
S ECM
Ff
P0776
(05 −60 1)Pressure Control Solenoid ”B”
Performance
(Shift Solenoid Valve SL2)
S Shift solenoid valve SL2 remains open or closed
S Valve body is blocked
S Shift solenoid valve SL2
S Automatic transaxle (clutch, brake or gear etc.)
S ECM
Ff
P0778
(05 −604)Pressure Control Solenoid ”B”
Electrical
(Shift Solenoid Valve SL2)SOpen or short in shift solenoid valve SL2 circuit
S Shift solenoid valve SL2
S ECM
Ff
P0793
(05 −607)Intermediate Shaft Speed Sen-
sor ”A”
SOpen or short in transmission revolution sensor NC (speed
sensor NC) circuit
S Transmission revolution sensor NC (speed sensor NC)
S ECM
Ff
P0796
(05 −610)Pressure Control Solenoid ”C”
Performance
(Shift Solenoid Valve SL3)
SShift solenoid valve SL3 remains open or closed
S Valve body is blocked
S Shift solenoid valve SL3
S Automatic transaxle (clutch, brake or gear etc.)
S ECM
Ff
P0798
(05 −613)Pressure Control Solenoid ”C”
Electrical
(Shift Solenoid Valve SL3)SOpen or short in shift solenoid valve SL3 circuit
S Shift solenoid valve SL3
S ECM
Ff
P0982
(05 −616)Shift Solenoid ”B” Control Circuit
Low (Shift Solenoid Valve S4)SShort in shift solenoid valve S4 circuit
S Shift solenoid valve S4
S ECM
Ff
P0983
(05 −616)Shift Solenoid ”B” Control Circuit
High (Shift Solenoid Valve S4)SOpen in shift solenoid valve S4 circuit
S Shift solenoid valve S4
S ECM
Ff
P0985
(05 −619)Shift Solenoid ”E” Control Circuit
Low (Shift Solenoid Valve SR)SShort in shift solenoid valve SR circuit
S Shift solenoid valve SR
S ECM
Ff
P0986
(05 −619)Shift Solenoid ”E” Control Circuit
High (Shift Solenoid Valve SR)SOpen in shift solenoid valve SR circuit
S Shift solenoid valve SR
S ECM
Ff
P27 16
(05 −622)Pressure Control Solenoid ”D”
Electrical
(Shift Solenoid Valve SLT)SOpen or short in shift solenoid valve SLT circuit
S Shift solenoid valve SLT
S ECM
Ff

05JLF−01
05 −562−
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U 151E)
AVENSIS Supplement (RM 1045E)
DATA LIST/ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the hand −held tester, you can read the value of the switch, sensor,
actuator and so on without parts removal. Reading the DATA LIST as the first step of troubleshooting is one
method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand −held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ”ON” button of the hand −held tester.
(f) Select the item ”DIAGNOSIS / OBD/MOBD / DATA LIST”.
(g) According to the display on tester, read the ”DATA LIST”.
ItemMeasurement Item/
Range (display)Normal ConditionDiagnostic Note
STOP LIGHT SWStop light SW Status/ ON or OFFS Brake Pedal is depressed: ON
S Brake Pedal is released: OFF−
REVERSEPNP SW Status/
ON or OFFShift lever position is;
R: ON
Except R: OFF
When the shift lever position dis-
played on the hand −held tester dif-
fers from the actual position, ad-
justment of the PNP switch or the
shift cable may be incorrect.
HINT:
When the failure still occurs even
after adjusting these parts,
see page 05 −566.
DRIVEPNP SW Status/
ON or OFFShift lever position is;
D and S: ON
Except D and S: OFF


SHIFTActual Gear Position/
1 st, 2nd, 3rd, 4th or 5thShift lever position is;
SD: 1st, 2nd, 3rd, 4th or 5th
S S: 1st, 2nd, 3rd, 4th or 5th
−
LOCK UP SOLLock Up Solenoid Status/
ON or OFFSLock Up: ON
S Except Lock Up: OFF−
SOLENOID (SLT)Shift Solenoid SLT Status/
ON or OFF
SAccelerator pedal is depressed:
OFF
S Accelerator pedal is released:
ON
−
AT FLUID TEMP
ATF Temp. Sensor Value/
min.: −40 _C( −40 _F)
max.: 2 15_C(4 19_F)S After Stall Test;
Approx. 80 _C( 176 _F)
S Equal to ambient temperature
when the engine is coldIf the value is ” −40 _C( −40 _F)” or
”2 15_C(4 19_F)”, ATF temp. sen-
sor circuit is opened or shorted.
SPD (NC)Counter Gear Speed/
display: 50 r/min
[HINT]
3rd when shift lever position is D
position (After warming up the en-
gine);
SIntermediate shaft speed (NC)
becomes close to the engine
speed.
−

05JLE−01
05−560− DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U151E)
AVENSIS Supplement (RM1045E)
FAIL−SAFE CHART
1. FAIL−SAFE
This function minimizes the loss of the ECT functions when any malfunction occurs in each sensor or sole-
noid.
(a) ATF (Automatic Transmission Fluid) temperature sensor:
When the ATF temperature sensor has a malfunction, 5th upshift is prohibited.
(b) Counter gear speed sensor NC (Speed sensor NC):
When the counter gear speed sensor has a malfunction, 5th upshift is prohibited.
(c) Shift solenoid valve DSL:
When the solenoid valve DSL has a malfunction, the current to the solenoid valve is stopped.
This stops lock−up control, then fuel economy decreases.

056IN−05
−
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U 151E)05 −545
AVENSIS Supplement (RM 1045E)
PROBLEM SYMPTOMS TABLE
HINT:
If a normal code is displayed during the diagnostic trouble code check although the trouble still occurs, check
the electrical circuits for each symptom in the order given in the charts on the following pages and proceed
to the page given for troubleshooting.
The Matrix Chart is divided into 2 chapters.
1. Chapter 1: Electronic Circuit Matrix Chart
S Refer to the table below when the trouble cause is considered to be electrical.
S If the instruction ”Proceed to next circuit inspection shown on matrix chart” is given in the flow chart
of each circuit, proceed to the circuit with the next highest number in the table to continue the check.
S If the trouble still occurs even though there are no abnormalities in any of the other circuits, check and
replace the ECM.
HINT:
* 1 : When the circuit on which mark * 1 is attached is a malfunction, DTC could be output (see page 05 −564).
*2: LHD
SymptomSuspect AreaSee page
No down −shift
(A particular gear, from 1st to 4th gear, is not down −shifted)
1. Shift solenoid valve (SL 1) circuit*1
2. Shift solenoid valve (SL2) circuit*1
3. Shift solenoid valve (SL3) circuit*1
4. Shift solenoid valve (SR) circuit*1
5. ECM
05 −589
05 −60 1
05 −61 0
05 −598
0 1− 32
No down −shift (5th
4th)
1. Park/neutral position switch circuit *1
2. Shift solenoid valve (S4) circuit*1
3. ECM
05 −566
05 −595
0 1− 32
No up −shift
(A particular gear, from 1st to 4th gear, is not up −shifted)1. Shift solenoid valve (SL 1) circuit*1
2. Shift solenoid valve (SL2) circuit*1
3. ECM
05 −589
05 −60 1
0 1− 32
No up −shift (4th
5th)
1. Park/neutral position switch circuit *1
2. Shift solenoid valve (S4) circuit*1
3. ECM
05 −566
05 −595
0 1− 32
No lock −up
1. Shift solenoid valve (DSL) circuit*1
2. Stop light switch circuit*1
3. Engine coolant temp. sensor circuit*1
4. ECM
05 −582
05 −580
05 −31
0 1− 32
No lock −up off1. Shift solenoid valve (DSL) circuit*1
2. ECM
05 −582
0 1− 32
Shift point too high or too low
1. Throttle position sensor circuit*1
2. Shift solenoid valve (SLT) circuit*1
3. ECM
05 −31
05 −622
0 1− 32
Up −shift to 5th from 4th while engine is cold1. Engine coolant temp. sensor circuit*1
2. ECM
05 −31
0 1− 32
No gear change by shifting into ”+” or ” −” while the shift lever is in
the S position1 . Transmission control switch circuit
2. ECM05 −625
0 1− 32
Harsh engagement (N
D)1. Shift solenoid valve (SL 1) circuit*1
2. ECM
05 −589
0 1− 32
Harsh engagement (Lock −up)1. Shift solenoid valve (SL2) circuit*1
2. ECM
05 −60 1
0 1− 32
Harsh engagement (Any driving position)1. Shift solenoid valve (SLT) circuit*1
2. ECM
05 −622
0 1− 32
Poor acceleration1. Shift solenoid valve (SLT) circuit*1
2. ECM
05 −622
0 1− 32

G31593
Warmed up
sufficiently
Approx.100 km/h
(62 mph)
Vehicle Speed
Approx. 80 km/h
(50 mph)
0
Normal acceleration
through all the gears from1st to 5th
Lock−up ON
Vehicle Speed
Stop
(Idling)
Maintain a constant speed or gradual acceleration (with the throttle open)
for 3 minutes or more.
*1 05−544
− DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U151E)
AVENSIS Supplement (RM1045E)
HINT:
*1: Drive at such a speed in the uppermost gear, to engage lock−up. The vehicle can be driven at a speed
lower than that in the above diagram under the lock−up condition.
NOTICE:
It is necessary to drive the vehicle for approximately 30 minutes to detect DTC P0711(ATF tempera-
ture sensor malfunction).