TRANSFER ASSEMBLY
TF-111
C
E
F
G
H
I
J
K
L
MA
B
TF
TRANSFER ASSEMBLYPFP:33100
Removal and InstallationEDS0032O
REMOVAL
1. Switch 4WD shift switch to 2WD and set transfer assembly to 2WD.
2. Remove the drain plug and gasket. Drain the fluid. Refer toTF-12, "
Replacement".
3. Remove the transmission undercover.
4. Remove the main muffler. Refer toEX-3, "
Removal and Installation".
5. Remove the front and rear propeller shafts. Refer toPR-4, "
Removal and Installation"(front) andPR-8,
"Removal and Installation"(rear).
CAUTION:
Do not damage spline, sleeve yoke and rear oil seal when removing rear propeller shaft.
NOTE:
Insert a plug into the rear oil seal after removing the rear propeller shaft.
6. Remove transmission bolts. Refer toAT-247, "
Removal and Installation"(A/T models) orMT-16,
"Removal and Installation from Vehicle"(M/T models).
7. Position two suitable jacks under the transmission and transfer assembly.
8. Remove the transmission crossmember. Refer toAT- 2 4 7 , "
Removal and Installation"(A/T models) orMT-
16, "Removal and Installation from Vehicle"(M/T models).
WARNING:
Support transmission and transfer assembly using two suitable jacks while removing transmis-
sion crossmember.
9. Disconnect the electrical connectors from the following:
lAT P s w i t c h
l4LO switch
lWait detection switch
lTransfer control device
10. Disconnect each air breather hose from the following. Refer toTF-107, "
A/T MODELS"(A/T models) or
TF-109, "
M/T MODELS"(M/T models).
lTransfer control device
lBreather tube (transfer)
11. Remove the transfer to transmission and transmission to trans-
fer bolts.
WARNING:
Support transfer assembly with suitable jack while remov-
ing it.
12. Remove the transfer assembly.
CAUTION:
Do not damage transmission rear oil seal.
SDIA3181E
PRECAUTION
WW-3
C
D
E
F
G
H
I
J
L
MA
B
WW
PRECAUTIONPFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EKS00N1N
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
lTo avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
lImproper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
lDo not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Wiring Diagrams and Trouble DiagnosisEKS00L9V
When you read wiring diagrams, refer to the following:
lRefer toGI-15, "HowtoReadWiringDiagrams".
lRefer toPG-4, "POWER SUPPLY ROUTING CIRCUIT".
When you perform trouble diagnosis, refer to the following:
lRefer toGI-11, "How to Follow Trouble Diagnoses".
lRefer toGI-24, "How to Perform Efficient Diagnosis for an Electrical Incident".
