2005 NISSAN NAVARA heater

SE-24
FRONT SEAT
INSTALLATION
Install is in the reverse order of removal.
Disassembly and AssemblyEIS00BCC
SEAT CUSHION (POWER SEAT)
Disassembly
1. Remove the hog rings on the seat cushion frame, and then disconnect the seat harness connectors.
2. Remove the nuts, and then the seat cushion assembly.
3. Remove the screw, and remove the seat cushion front finisher.
4. Remove the screw, and remove the outer and inner seat cush-
ion finisher.
5. Remove the power seat switch knobs(1)(2) and then power seat
switch escutcheon(3).
6. Remove the retainer on the seat cushion frame, then remove the seat cushion trim&pad.
7. Remove the hog ring to separate the seat cushion trim, pad, and seat cushion heater unit.
8. Remove the screw and remove the power seat switch.
MIIB0737E
MIIB0738E
MIIB0739E
MIIB0740E

FRONT SEAT
SE-25
C
D
E
F
G
H
J
K
L
MA
B
SE
Assembly
Assemble in the reverse order of disassembly.
SEAT CUSHION (MANUAL SEAT)
Disassembly
1. Hang snap ring(1) on wire(A), and pull it up to remove.Remove
lifter dial(2).
2. Remove the hog rings on the seat cushion frame, and then disconnect the seat harness connectors.
3. Remove the nuts, and then the seat cushion assembly.
4. Pull up tabs of reclining lever from inside.Slide knob forward to
remove.
5. Remove the screw, and remove the outer and inner seat cush-
ion finisher.
6. Remove the retainer on the seat cushion frame, then remove the seat cushion trim&pad.
7. Remove the hog rings to separate the seat cushion trim, pad, and seat cushion heater unit.
Assembly
Assemble in the reverse order of disassembly.
MIIB0741E
MIIB0742E
MIIB0743E
MIIB0739E

FRONT SEAT
SE-27
C
D
E
F
G
H
J
K
L
MA
B
SE
6. Remove the headrest holder.
Squeeze and pull up headrest holder tabs to remove from
seatback frame.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
7. Disconnect the seatback heater harness. Remove the seatback trim and pad assembly. Remove the hog
ring to separate the seatback trim from the pad and the heater unit.
Assembly
Assemble in the reverse order of disassembly.
SEATBACK (FRAT FOLD SEAT)
Disassembly
WARNING:
Removal of front side air bag module should only be done to allow deployment of front side air bag
module prior to disposal of seatback assembly.
NOTE:
Only complete seatback assemblies can be replaced.
1. Pull the seatback knob(1) and remove the seatback knob
cover(2).
2. Remove the seatback board from the back of the seatback.
PIIB4084J
MIIB0748E
MIIB0745E

SE-28
FRONT SEAT
3. Remove the retainer(1) from the seatback frame(2).
4. Remove the hog ring(A) and separate the seatback trim lower
side.
5. Remove the mounting nut of side air bag module.
6. Remove the headrest holder.
Squeeze and pull up headrest holder tabs to remove from
seatback frame.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
7. Disconnect the seatback heater harness. Remove the seatback trim and pad assembly. Remove the hog
ring to separate the seatback trim from the pad and the heater unit.
8. Remove fixing clip(2) from the seatback frame(1) and remove
cablewirefromthereleaselatchlever(3),andthenremove
screw and remove the seatback knob.
Assembly
Assemble in the reverse order of disassembly.
MIIB0746E
MIIB0747E
PIIB4084J
MIIB0749E