2005 MERCEDES-BENZ SPRINTER injector

REMOVAL
WARNING: HIGH-PRESSURE FUEL LINES DELIVER
DIESEL FUEL UNDER EXTREME PRESSURE FROM
THE INJECTION PUMP TO THE FUEL INJECTORS.
THIS MAY BE AS HIGH AS 1600BAR (23,200 PSI).
USE EXTREME CAUTION WHEN INSPECTING FOR
HIGH-PRESSURE FUEL LEAKS. FUEL UNDER THIS
AMOUNT OF PRESSURE CAN PENETRATE SKIN
CAUSING PERSONAL INJURY OR DEATH. INSPECT
FOR HIGH-PRESSURE LEAKS WITH A SHEET OF
CARD BOARD. WEAR SAFETY GOGGLES AND
ADEQUATE PROTECTIVE CLOTHING WHEN SER-
VICING FUEL SYSTEM.
WARNING: NO SPARKS, OPEN FLAMES OR SMOK-
ING. RISK OF POISONING FROM INHALING AND
SWALLOWING FUEL. RISK OF INJURY TO EYES
AND SKIN FROM CONTACT WITH FUEL. POUR
FUELS ONLY INTO SUITABLE AND APPROPRI-
ATELY MARKED CONTAINERS. WEAR PROTECTIVE
CLOTHING.
(1) Disconnect negative battery cable.
(2) Remove fuel rail (Refer to 14 - FUEL SYSTEM/
FUEL INJECTION/FUEL INJECTOR - REMOVAL).
(3) Clamp fuel rail securely in vise with protective
jaws.
NOTE: Once removed, the pressure solenoid must
always be replaced.
(4) Remove fuel pressure solenoid retaining screws
and remove solenoid (Fig. 16).
INSTALLATION
WARNING: HIGH-PRESSURE FUEL LINES DELIVER
DIESEL FUEL UNDER EXTREME PRESSURE FROM
THE INJECTION PUMP TO THE FUEL INJECTORS.
THIS MAY BE AS HIGH AS 1600BAR (23,200 PSI).
USE EXTREME CAUTION WHEN INSPECTING FOR
HIGH-PRESSURE FUEL LEAKS. FUEL UNDER THIS
AMOUNT OF PRESSURE CAN PENETRATE SKIN
CAUSING PERSONAL INJURY OR DEATH. INSPECT
FOR HIGH-PRESSURE LEAKS WITH A SHEET OF
CARD BOARD. WEAR SAFETY GOGGLES AND
ADEQUATE PROTECTIVE CLOTHING WHEN SER-
VICING FUEL SYSTEM.WARNING: NO SPARKS, OPEN FLAMES OR SMOK-
ING. RISK OF POISONING FROM INHALING AND
SWALLOWING FUEL. RISK OF INJURY TO EYES
AND SKIN FROM CONTACT WITH FUEL. POUR
FUELS ONLY INTO SUITABLE AND APPROPRI-
ATELY MARKED CONTAINERS. WEAR PROTECTIVE
CLOTHING.
NOTE: Apply a thin film of special grease to the
seals before installing. If the seals are damaged
when being installed, an internal leak may occur
which can not be recognized externally.
(1) Position fuel pressure solenoid to fuel rail and
retain with screws (Fig. 16). Tighten in two stages,
3N´m (26 lbs. in.) then 5N´m (44 lbs. ft.).
(2) Install fuel rail (Refer to 14 - FUEL SYSTEM/
FUEL INJECTION/FUEL INJECTOR - INSTALLA-
TION).
(3) Connect negative battery cable.
Fig. 16 FUEL PRESSURE SOLENOID ASSEMBLY
1 - RETAINING BOLT
2 - FUEL PRESSURE SOLENOID
3 - RETAINING BOLT
4 - O-RING LOCATION
5 - FUEL RAIL
6 - VISE
14 - 28 FUEL INJECTIONVA
FUEL PRESSURE SOLENOID (Continued)

CIRCUIT BREAKER - OPERATION......8W-97-2
CIRCUIT INFORMATION - DESCRIPTION . 8W-01-5
CLAMP PLATES - INSTALLATION,
SPRING..............................2-8
CLAMP PLATES - REMOVAL, SPRING......2-8
CLASSIFICATION - STANDARD
PROCEDURE, INJECTOR...............14-22
CLEARANCE LAMP BULB -
INSTALLATION........................8L-8
CLEARANCE LAMP BULB - REMOVAL.....8L-8
CLEARANCE LAMP UNIT -
INSTALLATION........................8L-9
CLEARANCE LAMP UNIT - REMOVAL......8L-8
CLOCK - DESCRIPTION................8J-13
CLOCK - OPERATION..................8J-14
CLOCKSPRING - DESCRIPTION.........8O-12
CLOCKSPRING - INSTALLATION.........8O-15
CLOCKSPRING - OPERATION...........8O-13
CLOCKSPRING - REMOVAL............8O-14
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-13
CLOGGED INDICATOR - DESCRIPTION,
FUEL FILTER........................8J-15
CLOGGED INDICATOR - OPERATION,
FUEL FILTER........................8J-15
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-7
CLUSTER - INSTALLATION, INSTRUMENT . . 8J-9
CLUSTER - INSTALLATION, TOP COVER . . . 23-62
CLUSTER - OPERATION, INSTRUMENT.....8J-5
CLUSTER - REMOVAL, INSTRUMENT......8J-7
CLUSTER - REMOVAL, TOP COVER......23-62
CLUSTER BEZEL - INSTALLATION........23-54
CLUSTER BEZEL - REMOVAL...........23-53
CLUTCH - ASSEMBLY, FREEWHEELING . . 21-107
CLUTCH - DESCRIPTION, A/C
COMPRESSOR........................24-8
CLUTCH - DESCRIPTION,
FREEWHEELING.....................21-105
CLUTCH - DISASSEMBLY,
FREEWHEELING.....................21-106
CLUTCH - INSTALLATION, FAN DRIVE
VISCOUS............................7-16
CLUTCH - OPERATION, A/C
COMPRESSOR........................24-8
CLUTCH - OPERATION, FREEWHEELING . . 21-105
CLUTCH - REMOVAL, FAN DRIVE
VISCOUS............................7-16
CLUTCH AIR GAP - STANDARD
PROCEDURE, COMPRESSOR............24-9
CLUTCH B1 - ASSEMBLY, HOLDING.....21-113
CLUTCH B1 - DISASSEMBLY, HOLDING . . 21-112
CLUTCH B2 - ASSEMBLY, HOLDING.....21-116
CLUTCH B2 - DISASSEMBLY, HOLDING . . 21-115
CLUTCH BREAK-IN - STANDARD
PROCEDURE, COMPRESSOR............24-9
CLUTCH COIL - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-12
CLUTCH K1 - ASSEMBLY, DRIVING.......21-75
CLUTCH K1 - DISASSEMBLY, DRIVING....21-74
CLUTCH K2 - ASSEMBLY, DRIVING.......21-78
CLUTCH K2 - DISASSEMBLY, DRIVING....21-76
CLUTCH K3 - ASSEMBLY, DRIVING.......21-80
CLUTCH K3 - DISASSEMBLY, DRIVING....21-80
CLUTCH/COIL - INSPECTION,
COMPRESSOR.......................24-10
CLUTCHES - DESCRIPTION, DRIVING.....21-72
CLUTCHES - DESCRIPTION, HOLDING . . . 21-111
CLUTCHES - OPERATION, DRIVING......21-72
CLUTCHES - OPERATION, HOLDING.....21-112
CODES - SPECIFICATIONS, PAINT........23-74
COIL - DIAGNOSIS AND TESTING,
COMPRESSOR CLUTCH...............24-12
COLUMN OPENING COVER -
INSTALLATION, STEERING.............23-66
COLUMN OPENING COVER - REMOVAL,
STEERING..........................23-66
COMPRESSION TESTING ENGINE -
STANDARD PROCEDURE.................9-3
COMPRESSOR - DESCRIPTION, A/C......24-49
COMPRESSOR - INSTALLATION, A/C
.....24-51
COMPRESSOR - OPERATION, A/C
........24-49
COMPRESSOR - REMOVAL, A/C
.........24-50
COMPRESSOR CLUTCH - DESCRIPTION,
A/C
................................24-8
COMPRESSOR CLUTCH - OPERATION,
A/C
................................24-8COMPRESSOR CLUTCH AIR GAP -
STANDARD PROCEDURE................24-9
COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE................24-9
COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-12
COMPRESSOR CLUTCH/COIL -
INSPECTION........................24-10
COMPRESSOR NOISE - DIAGNOSIS AND
TESTING...........................24-49
CONDENSER - DESCRIPTION, A/C.......24-52
CONDENSER - INSTALLATION, A/C.......24-52
CONDENSER - OPERATION, A/C.........24-52
CONDENSER - REMOVAL, A/C..........24-52
CONDITIONER - DESCRIPTION, HEATER
AND AIR ............................24-1
CONDITIONER - OPERATION, HEATER
AND AIR ............................24-2
CONNECTING FUEL LINES - STANDARD
PROCEDURE, DISCONNECTING...........14-2
CONNECTING ROD - DESCRIPTION,
PISTON.............................9-40
CONNECTING RODS - STANDARD
PROCEDURE, CHECKING AND
REPAIRING..........................9-40
CONNECTOR - INSTALLATION........8W-01-9
CONNECTOR - REMOVAL............8W-01-8
CONNECTOR, GROUND AND SPLICE
INFORMATION - DESCRIPTION........8W-01-5
CONNECTOR/GROUND/SPLICE LOCATION
- DESCRIPTION....................8W-91-1
CONTACT - DESCRIPTION, PARK/
NEUTRAL..........................21-139
CONTACT - OPERATION, PARK/NEUTRAL . 21-140
CONTAMINATION - DIAGNOSIS AND
TESTING, BRAKE FLUID................5-14
CONTAMINATION - DIAGNOSIS AND
TESTING, FLUID....................21-102
CONTINUITY - STANDARD PROCEDURE,
TESTING.........................8W-01-8
CONTROL ARM - INSTALLATION, LOWER . . . 2-6
CONTROL ARM - REMOVAL, LOWER.......2-6
CONTROL INDICATOR - DESCRIPTION,
TRACTION..........................8J-24
CONTROL INDICATOR - OPERATION,
TRACTION..........................8J-24
CONTROL MALFUNCTION INDICATOR -
DESCRIPTION, TRACTION..............8J-25
CONTROL MALFUNCTION INDICATOR -
OPERATION, TRACTION................8J-25
CONTROL MODULE - DESCRIPTION......24-24
CONTROL MODULE - DESCRIPTION,
AIRBAG.............................8O-8
CONTROL MODULE - DESCRIPTION,
ENGINE.............................8E-3
CONTROL MODULE - DESCRIPTION,
TRANSMISSION.......................8E-5
CONTROL MODULE - DIAGNOSIS AND
TESTING...........................24-24
CONTROL MODULE - INSTALLATION.....24-25
CONTROL MODULE - INSTALLATION,
AIRBAG............................8O-11
CONTROL MODULE - INSTALLATION,
ENGINE.............................8E-4
CONTROL MODULE - OPERATION.......24-24
CONTROL MODULE - OPERATION,
AIRBAG.............................8O-9
CONTROL MODULE - OPERATION,
TRANSMISSION.......................8E-5
CONTROL MODULE - REMOVAL.........24-24
CONTROL MODULE - REMOVAL, AIRBAG . 8O-10
CONTROL MODULE - REMOVAL, ENGINE . . . 8E-4
CONTROLLER - INSTALLATION, ALB......5-15
CONTROLLER - REMOVAL, ALB..........5-15
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION........................8E-3
CONTROLLER ANTILOCK BRAKE -
INSTALLATION........................8E-3
CONTROLLER ANTILOCK BRAKE -
REMOVAL...........................8E-3
CONVERTER - DESCRIPTION, TORQUE . . . 21-141
CONVERTER - INSTALLATION, CATALYTIC . . 11-3
CONVERTER - INSTALLATION, TORQUE
. . 21-146
CONVERTER - OPERATION, TORQUE
....21-143
CONVERTER - REMOVAL, CATALYTIC
......11-3
CONVERTER - REMOVAL, TORQUE
......21-146
CONVERTER HUB SEAL - INSTALLATION,
TORQUE
...........................21-147CONVERTER HUB SEAL - REMOVAL,
TORQUE...........................21-147
COOLANT - DESCRIPTION...............7-9
COOLANT - DESCRIPTION, ENGINE........0-1
COOLANT - DESCRIPTION, HOAT..........0-2
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL..................7-11
COOLANT LEVEL SENSOR -
INSTALLATION........................7-13
COOLANT LEVEL SENSOR - REMOVAL.....7-13
COOLANT LOW INDICATOR -
DESCRIPTION.......................8J-14
COOLANT LOW INDICATOR - OPERATION . 8J-14
COOLANT PUMP - DESCRIPTION,
ELECTRIC..........................24-57
COOLANT PUMP - INSTALLATION,
ELECTRIC..........................24-57
COOLANT PUMP - OPERATION,
ELECTRIC..........................24-57
COOLANT PUMP - REMOVAL, ELECTRIC . . 24-57
COOLANT TEMP SENSOR -
DESCRIPTION, ENGINE.................7-14
COOLANT TEMP SENSOR -
INSTALLATION, ENGINE................7-15
COOLANT TEMP SENSOR - REMOVAL,
ENGINE.............................7-14
COOLANT THERMOSTAT -
INSTALLATION, ENGINE................7-16
COOLANT THERMOSTAT - REMOVAL,
ENGINE.............................7-15
COOLER & LINES - INSTALLATION, OIL....9-50
COOLER & LINES - REMOVAL, OIL.......9-50
COOLER AND PLUMBING - CLEANING,
CHARGE AIR.........................11-5
COOLER AND PLUMBING -
DESCRIPTION, CHARGE AIR.............11-4
COOLER AND PLUMBING - INSPECTION,
CHARGE AIR.........................11-5
COOLER AND PLUMBING -
INSTALLATION, CHARGE AIR............11-5
COOLER AND PLUMBING - OPERATION,
CHARGE AIR.........................11-4
COOLER AND PLUMBING - REMOVAL,
CHARGE AIR.........................11-5
COOLER SYSTEM - LEAKS - DIAGNOSIS
AND TESTING, CHARGE AIR.............11-4
COOLER TUBE - INSTALLATION, FLUID . . . 19-14
COOLER TUBE - INSTALLATION, RETURN
HOSE FROM GEAR TO................19-15
COOLER TUBE - INSTALLATION, RETURN
LINE FROM PUMP TO.................19-15
COOLER TUBE - REMOVAL, FLUID.......19-14
COOLER TUBE - REMOVAL, RETURN
HOSE FROM GEAR TO................19-15
COOLER TUBE - REMOVAL, RETURN
LINE FROM PUMP TO.................19-15
COOLING SYSTEM - DIAGNOSIS AND
TESTING.............................7-2
COOLING SYSTEM - OPERATION..........7-1
COOLING SYSTEM - STANDARD
PROCEDURE, DRAINING................7-12
COOLING SYSTEM - STANDARD
PROCEDURE, REFILLING................7-12
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING........................7-10
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION........................24-1
CORE - DESCRIPTION, HEATER.........24-57
CORE - INSTALLATION, HEATER.........24-58
CORE - OPERATION, HEATER...........24-57
CORE - REMOVAL, HEATER............24-58
CORE AND OIL GALLERY PLUGS -
STANDARD PROCEDURE, REPLACING
ENGINE.............................9-34
COVER - CLUSTER - INSTALLATION, TOP . 23-62
COVER - CLUSTER - REMOVAL, TOP.....23-62
COVER - INSTALLATION, CYLINDER
HEAD FRONT.........................9-26
COVER - INSTALLATION, ENGINE..........9-7
COVER - INSTALLATION, STEERING
COLUMN OPENING...................23-66
COVER - INSTALLATION, TIMING CHAIN
. . . 9-60
COVER - INSTALLATION, TOP
...........23-65
COVER - REMOVAL, CYLINDER HEAD
FRONT
..............................9-23
COVER - REMOVAL, ENGINE
..............9-4
COVER - REMOVAL, STEERING COLUMN
OPENING
...........................23-66
4 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

FREEWHEELING CLUTCH -
DISASSEMBLY......................21-106
FREEWHEELING CLUTCH - OPERATION . . 21-105
FROM FUEL FILTER - STANDARD
PROCEDURES, DRAINING WATER........14-2
FROM GEAR TO COOLER TUBE -
INSTALLATION, RETURN HOSE..........19-15
FROM GEAR TO COOLER TUBE -
REMOVAL, RETURN HOSE.............19-15
FROM PUMP TO COOLER TUBE -
INSTALLATION, RETURN LINE..........19-15
FROM PUMP TO COOLER TUBE -
REMOVAL, RETURN LINE..............19-15
FRONT - INSTALLATION............5-14,5-24
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-38
FRONT - INSTALLATION, SEAT..........23-77
FRONT - INSTALLATION, SEAT
ADJUSTERS.........................23-78
FRONT - INSTALLATION, SEAT BACK.....23-77
FRONT - INSTALLATION, SEAT CUSHION . . 23-78
FRONT - REMOVAL................5-13,5-24
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-38
FRONT - REMOVAL, SEAT..............23-77
FRONT - REMOVAL, SEAT ADJUSTERS . . . 23-78
FRONT - REMOVAL, SEAT BACK.........23-77
FRONT - REMOVAL, SEAT CUSHION......23-78
FRONT BUMPER - STEPS -
INSTALLATION........................13-2
FRONT BUMPER - STEPS - REMOVAL.....13-2
FRONT COVER - INSTALLATION,
CYLINDER HEAD......................9-26
FRONT COVER - REMOVAL, CYLINDER
HEAD...............................9-23
FRONT DOOR INNER BELT
WEATHERSTRIP - INSTALLATION........23-87
FRONT DOOR INNER BELT
WEATHERSTRIP - REMOVAL............23-87
FRONT DOOR OUTER BELT
WEATHERSTRIP - INSTALLATION........23-87
FRONT DOOR OUTER BELT
WEATHERSTRIP - REMOVAL............23-87
FRONT (DRW) - INSTALLATION . . 5-11,5-13,5-21
FRONT (DRW) - REMOVAL.......5-12,5-20,5-9
FRONT FASCIA - INSTALLATION..........13-2
FRONT FASCIA - REMOVAL..............13-2
FRONT LAMP UNIT - ADJUSTMENT......8L-12
FRONT LAMP UNIT - INSTALLATION.....8L-12
FRONT LAMP UNIT - REMOVAL.........8L-12
FRONT POSITION LAMP BULB -
INSTALLATION.......................8L-14
FRONT POSITION LAMP BULB -
REMOVAL..........................8L-14
FRONT SEAT BELT & RETRACTOR -
INSTALLATION......................8O-21
FRONT SEAT BELT & RETRACTOR -
REMOVAL..........................8O-19
FRONT SEAT BELT BUCKLE -
INSTALLATION......................8O-23
FRONT SEAT BELT BUCKLE - REMOVAL . . 8O-22
FRONT (SRW) - INSTALLATION . . 5-10,5-12,5-21
FRONT (SRW) - REMOVAL.......5-11,5-19,5-9
FRONT SUSPENSION, SPECIAL TOOLS....19-11
FRONT SUSPENSION, SPECIAL TOOLS.....2-2
FRONT TURN/PARK/SIDE MARKER LAMP
BULB - INSTALLATION................8L-15
FRONT TURN/PARK/SIDE MARKER LAMP
BULB - REMOVAL....................8L-14
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-30
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-30
FUEL DOSING PUMP - DESCRIPTION.....24-74
FUEL DOSING PUMP - INSTALLATION....24-74
FUEL DOSING PUMP - OPERATION......24-74
FUEL DOSING PUMP - REMOVAL........24-74
FUEL FILL DOOR - INSTALLATION.......23-47
FUEL FILL DOOR - REMOVAL...........23-47
FUEL FILTER - DESCRIPTION............14-5
FUEL FILTER - INSTALLATION
............14-6
FUEL FILTER - OPERATION
..............14-5
FUEL FILTER - REMOVAL
...............14-5
FUEL FILTER - STANDARD
PROCEDURES, DRAINING WATER
FROM
..............................14-2
FUEL FILTER CLOGGED INDICATOR -
DESCRIPTION
.......................8J-15FUEL FILTER CLOGGED INDICATOR -
OPERATION.........................8J-15
FUEL GAUGE - DESCRIPTION...........8J-16
FUEL GAUGE - OPERATION.............8J-16
FUEL INDICATOR - DESCRIPTION, LOW . . . 8J-18
FUEL INDICATOR - OPERATION, LOW.....8J-18
FUEL INJECTOR, DESCRIPTION.........14-20
FUEL INJECTORS - STANDARD
PROCEDURE, CLEANING...............14-22
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION.......................14-15
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION.......................14-15
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL..........................14-15
FUEL LINE - INSTALLATION............24-76
FUEL LINE - REMOVAL................24-75
FUEL LINES - DIAGNOSIS AND TESTING,
HIGH PRESSURE......................14-1
FUEL LINES - STANDARD PROCEDURE,
DISCONNECTING AND CONNECTING......14-2
FUEL PRESSURE SOLENOID -
DESCRIPTION.......................14-27
FUEL PRESSURE SOLENOID -
INSTALLATION.......................14-28
FUEL PRESSURE SOLENOID -
OPERATION.........................14-27
FUEL PRESSURE SOLENOID - REMOVAL . . 14-28
FUEL PUMP TEST - STANDARD
PROCEDURE, LOW PRESSURE...........14-3
FUEL RAIL - DESCRIPTION..............14-11
FUEL RAIL - INSTALLATION............14-11
FUEL RAIL - OPERATION...............14-11
FUEL RAIL - REMOVAL................14-11
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION........................0-1
FUEL SENSOR - DESCRIPTION, WATER
IN ................................14-16
FUEL SENSOR - OPERATION, WATER IN . . 14-16
FUEL SHUTOFF SOL - DESCRIPTION, HI
PRESSURE.........................14-16
FUEL SHUTOFF SOL - OPERATION, HI
PRESSURE.........................14-16
FUEL SUPPLY RESTRICTIONS -
DIAGNOSIS AND TESTING..............14-5
FUEL SYSTEM - DIAGNOSIS AND
TESTING, AIR IN......................14-2
FUEL SYSTEM COMPONENTS -
STANDARD PROCEDURES, CLEANING.....14-2
FUEL SYSTEM PRESSURE - WARNING,
HIGH...............................14-1
FUEL SYSTEM, SPECIAL TOOLS..........14-5
FUEL TANK - DESCRIPTION............14-12
FUEL TANK - INSTALLATION............14-13
FUEL TANK - REMOVAL...............14-12
FUEL TANK MODULE - DESCRIPTION.....14-13
FUEL TANK MODULE - INSTALLATION....14-14
FUEL TANK MODULE - REMOVAL........14-13
FUEL TEMPERATURE SENSOR -
DESCRIPTION.......................14-29
FUEL TEMPERATURE SENSOR -
INSTALLATION.......................14-29
FUEL TEMPERATURE SENSOR -
OPERATION.........................14-29
FUEL TEMPERATURE SENSOR -
REMOVAL..........................14-29
FUNCTION TEST - DIAGNOSIS AND
TESTING............................24-3
FUSE BLOCK #1 - DESCRIPTION......8W-97-2
FUSE BLOCK #1 - INSTALLATION......8W-97-3
FUSE BLOCK #1 - OPERATION........8W-97-2
FUSE BLOCK #1 - REMOVAL.........8W-97-3
FUSE BLOCK #2 - DESCRIPTION......8W-97-3
FUSE BLOCK #2 - OPERATION........8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.......8W-01-8
GALLERY PLUGS - STANDARD
PROCEDURE, REPLACING ENGINE
CORE AND OIL.......................9-34
GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH AIR
.............24-9
GAP AND FLUSH - SPECIFICATIONS
......23-88
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE
......................8J-15
GAUGE - DESCRIPTION, FUEL
...........8J-16
GAUGE - OPERATION, ENGINE
TEMPERATURE
......................8J-15GAUGE - OPERATION, FUEL............8J-16
GAUGES - DIAGNOSIS AND TESTING,
PRESSURE..........................22-8
GEAR - DESCRIPTION..................19-8
GEAR - INSTALLATION.................19-8
GEAR - INSTALLATION, INTERMEDIATE....9-66
GEAR - REMOVAL.....................19-8
GEAR - REMOVAL, INTERMEDIATE........9-61
GEAR SELECTOR INDICATOR -
DESCRIPTION.......................8J-17
GEAR SELECTOR INDICATOR -
OPERATION.........................8J-17
GEAR TO COOLER TUBE -
INSTALLATION, RETURN HOSE FROM....19-15
GEAR TO COOLER TUBE - REMOVAL,
RETURN HOSE FROM.................19-15
GEARSHIFT CABLE - DIAGNOSIS AND
TESTING..........................21-109
GEARSHIFT CABLE - INSTALLATION.....21-109
GEARSHIFT CABLE - REMOVAL........21-109
GEARTRAIN - ASSEMBLY, PLANETARY . . . 21-131
GEARTRAIN - DESCRIPTION,
PLANETARY........................21-130
GEARTRAIN - DISASSEMBLY,
PLANETARY........................21-131
GEARTRAIN - OPERATION, PLANETARY . . 21-130
GENERAL - WARNINGS.............8W-01-6
GENERATOR - DESCRIPTION...........8F-18
GENERATOR - INSTALLATION...........8F-18
GENERATOR - OPERATION.............8F-18
GENERATOR - REMOVAL...............8F-18
GENERATOR DECOUPLER - DIAGNOSIS
AND TESTING.......................8F-19
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-19
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-21
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-19
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-20
GLASS - INSTALLATION, DOOR....23-15,23-31,
23-46
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-49
GLASS - REMOVAL, DOOR . . . 23-15,23-31,23-46
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-49
GLOVE BOX - INSTALLATION...........23-56
GLOVE BOX - REMOVAL...............23-56
GLOW PLUG - INSTALLATION............8I-1
GLOW PLUG - REMOVAL................8I-1
GLOW PLUG RELAY - DESCRIPTION.......8I-2
GLOW PLUG RELAY - OPERATION........8I-2
GLOW PLUG RELAYS - DIAGNOSIS AND
TESTING.............................8I-2
GRILLE - INSTALLATION...............23-47
GRILLE - REMOVAL..................23-47
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-8
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-5
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO
..............................8W-01-8
GUIDE RAIL - INSTALLATION, CYLINDER
HEAD
...............................9-26
GUIDE RAIL - REMOVAL, CYLINDER
HEAD
...............................9-24
HANDLE - INSTALLATION, ASSIST
.......23-68
HANDLE - INSTALLATION, EXTERIOR
....23-16,
23-33,23-36
HANDLE - INSTALLATION, LATCH
RELEASE
...........................23-52
HANDLE - REMOVAL, ASSIST
...........23-68
HANDLE - REMOVAL, EXTERIOR
. . . 23-16,23-32,
23-36
HANDLE - REMOVAL, LATCH RELEASE
. . . 23-52
HANDLE ACTUATOR - INSTALLATION,
INSIDE
........................23-34,23-37
HANDLE ACTUATOR - REMOVAL, INSIDE
. 23-34,
23-37
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE
...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-6
VAINDEX 7
Description Group-Page Description Group-Page Description Group-Page

INDICATOR - OPERATION, COOLANT
LOW...............................8J-14
INDICATOR - OPERATION, FUEL FILTER
CLOGGED...........................8J-15
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-17
INDICATOR - OPERATION, HIGH BEAM....8J-17
INDICATOR - OPERATION, LOW FUEL.....8J-18
INDICATOR - OPERATION, LOW OIL
LEVEL.............................8J-18
INDICATOR - OPERATION,
MAINTENANCE.......................8J-19
INDICATOR - OPERATION, MULTI-
FUNCTION..........................8J-21
INDICATOR - OPERATION, SEATBELT.....8J-22
INDICATOR - OPERATION, TRACTION
CONTROL...........................8J-24
INDICATOR - OPERATION, TRACTION
CONTROL MALFUNCTION..............8J-25
INDICATOR - OPERATION, TURN SIGNAL . . 8J-25
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-26
INDICATOR - OPERATION, WASHER
FLUID..............................8J-27
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-28
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-20
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-20
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-12
INJECTOR CLASSIFICATION - STANDARD
PROCEDURE........................14-22
INJECTOR, DESCRIPTION - FUEL........14-20
INJECTORS - STANDARD PROCEDURE,
CLEANING FUEL.....................14-22
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-29
INLET AIR TEMPERATURE SENSOR -
INSTALLATION.......................14-30
INLET AIR TEMPERATURE SENSOR -
OPERATION.........................14-29
INLET AIR TEMPERATURE SENSOR -
REMOVAL..........................14-30
INLET HOSE - INSTALLATION...........24-78
INLET HOSE - REMOVAL...............24-78
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR...........23-87
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR..............23-87
INPUT SPEED SENSORS - DESCRIPTION . 21-119
INPUT SPEED SENSORS - OPERATION . . . 21-119
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-34,23-37
INSIDE HANDLE ACTUATOR -
REMOVAL.....................23-34,23-37
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-7
INSTRUMENT CLUSTER - INSTALLATION . . . 8J-9
INSTRUMENT CLUSTER - OPERATION.....8J-5
INSTRUMENT CLUSTER - REMOVAL......8J-7
INSTRUMENT PANEL - INSTALLATION....8L-29
INSTRUMENT PANEL - REMOVAL........8L-28
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-2
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-1
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-61
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-57
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-55
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-55
INSTRUMENT PANEL DUCTS -
INSTALLATION
.......................24-38
INSTRUMENT PANEL DUCTS - REMOVAL
. 24-37
INTAKE MANIFOLD - INSTALLATION
.......9-58
INTAKE MANIFOLD - REMOVAL
..........9-57
INTERIOR - CAUTION
.................23-67INTERIOR - DESCRIPTION, LAMPS/
LIGHTING..........................8L-25
INTERIOR - OPERATION, LAMPS/
LIGHTING..........................8L-26
INTERIOR LIGHTING - SPECIFICATIONS . . . 8L-26
INTERMEDIATE GEAR - INSTALLATION.....9-66
INTERMEDIATE GEAR - REMOVAL........9-61
INTERMEDIATE SHAFT - INSTALLATION....19-5
INTERMEDIATE SHAFT - REMOVAL.......19-5
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-2
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-9
INTRUSION SENSOR - INSTALLATION.....8Q-2
INTRUSION SENSOR - REMOVAL.........8Q-2
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
ISO FLARING - STANDARD PROCEDURE....5-8
JAMB SWITCH - INSTALLATION, DOOR . . . 8L-31
JAMB SWITCH - REMOVAL, DOOR.......8L-31
JET - DESCRIPTION, OIL................9-51
JET - INSTALLATION, OIL...............9-51
JET - REMOVAL, OIL...................9-51
JOINT - INSTALLATION, LOWER BALL......2-6
JOINT - REMOVAL, LOWER BALL..........2-6
JOURNALS - STANDARD PROCEDURE,
MEASURE CRANKSHAFT AND BLOCK......9-35
JUMP STARTING - STANDARD
PROCEDURE............................0-6
K1 - ASSEMBLY, DRIVING CLUTCH.......21-75
K1 - DISASSEMBLY, DRIVING CLUTCH....21-74
K2 - ASSEMBLY, DRIVING CLUTCH.......21-78
K2 - DISASSEMBLY, DRIVING CLUTCH....21-76
K3 - ASSEMBLY, DRIVING CLUTCH.......21-80
K3 - DISASSEMBLY, DRIVING CLUTCH....21-80
KEY - DESCRIPTION, TRANSPONDER.....8Q-5
KEY - OPERATION, TRANSPONDER.......8Q-5
KEY REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY................8Q-2
KEY REMOTE ENTRY MODULE -
INSTALLATION, SENTRY................8Q-4
KEY REMOTE ENTRY MODULE -
OPERATION, SENTRY..................8Q-3
KEY REMOTE ENTRY MODULE -
REMOVAL, SENTRY...................8Q-3
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-2
KEY/LOCK CYLINDER - INSTALLATION.....19-7
KEY/LOCK CYLINDER - REMOVAL........19-6
KNUCKLE - INSTALLATION...............2-5
KNUCKLE - REMOVAL...................2-5
LAMP BULB - INSTALLATION, BACKUP....8L-6
LAMP BULB - INSTALLATION,
BRAKE/PARK.........................8L-7
LAMP BULB - INSTALLATION,
CARGO/DOME.......................8L-27
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-7
LAMP BULB - INSTALLATION,
CLEARANCE..........................8L-8
LAMP BULB - INSTALLATION,
DOME/READING.....................8L-29
LAMP BULB - INSTALLATION,
ENTRY/EXIT.........................8L-32
LAMP BULB - INSTALLATION, FOG.......8L-10
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-14
LAMP BULB - INSTALLATION, FRONT
TURN/PARK/SIDE MARKER.............8L-15
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-18
LAMP BULB - INSTALLATION, REAR
SIDE MARKER.......................8L-21
LAMP BULB - INSTALLATION, REAR
TURN..............................8L-22
LAMP BULB - INSTALLATION, REPEATER . . 8L-22
LAMP BULB - REMOVAL, BACKUP........8L-5
LAMP BULB - REMOVAL, BRAKE/PARK....8L-7
LAMP BULB - REMOVAL, CARGO/DOME . . 8L-27
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-7
LAMP BULB - REMOVAL, CLEARANCE
.....8L-8
LAMP BULB - REMOVAL, DOME/
READING
...........................8L-29
LAMP BULB - REMOVAL, ENTRY/EXIT
....8L-31
LAMP BULB - REMOVAL, FOG
..........8L-10
LAMP BULB - REMOVAL, FRONT
POSITION
..........................8L-14LAMP BULB - REMOVAL, FRONT
TURN/PARK/SIDE MARKER.............8L-14
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-17
LAMP BULB - REMOVAL, REAR SIDE
MARKER...........................8L-21
LAMP BULB - REMOVAL, REAR TURN....8L-21
LAMP BULB - REMOVAL, REPEATER.....8L-22
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-20
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR.............8J-20
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING............................8L-9
LAMP RELAY - INSTALLATION, FOG......8L-11
LAMP RELAY - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP RELAY - REMOVAL, FOG.........8L-10
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-6
LAMP SWITCH - INSTALLATION, FOG....8L-12
LAMP SWITCH - REMOVAL, BRAKE.......8L-6
LAMP SWITCH - REMOVAL, FOG........8L-11
LAMP UN - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-8
LAMP UN - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-8
LAMP UNIT - ADJUSTMENT, FRONT......8L-12
LAMP UNIT - INSTALLATION, ASH
RECEIVER/CIGAR LIGHTER.............8L-27
LAMP UNIT - INSTALLATION, CARGO/
DOME...............................8L-28
LAMP UNIT - INSTALLATION,
CLEARANCE..........................8L-9
LAMP UNIT - INSTALLATION, DOME/
READING...........................8L-30
LAMP UNIT - INSTALLATION, ENTRY/
EXIT...............................8L-32
LAMP UNIT - INSTALLATION, FRONT.....8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-18
LAMP UNIT - INSTALLATION, REPEATER . . 8L-23
LAMP UNIT - INSTALLATION, TAIL.......8L-23
LAMP UNIT - REMOVAL, ASH
RECEIVER/CIGAR LIGHTER.............8L-27
LAMP UNIT - REMOVAL, CARGO/DOME . . . 8L-28
LAMP UNIT - REMOVAL, CLEARANCE.....8L-8
LAMP UNIT - REMOVAL, DOME/
READING...........................8L-30
LAMP UNIT - REMOVAL, ENTRY/EXIT....8L-32
LAMP UNIT - REMOVAL, FRONT.........8L-12
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-18
LAMP UNIT - REMOVAL, REPEATER......8L-22
LAMP UNIT - REMOVAL, TAIL...........8L-23
LAMP/INTRUSION SENSOR -
INSTALLATION, DOME.................8L-31
LAMP/INTRUSION SENSOR - REMOVAL,
DOME.............................8L-31
LAMP/INTRUSION SENSOR BULB -
INSTALLATION, DOME.................8L-30
LAMP/INTRUSION SENSOR BULB -
REMOVAL, DOME....................8L-30
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-3
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS......................8L-5
LAMPS/LIGHTING - INTERIOR -
DESCRIPTION.......................8L-25
LAMPS/LIGHTING - INTERIOR -
OPERATION.........................8L-26
LATCH - INSTALLATION.....23-18,23-35,23-51
LATCH - INSTALLATION, REAR..........23-40
LATCH - INSTALLATION, SAFETY........23-52
LATCH / LOCK CONTROL -
INSTALLATION.......................23-40
LATCH / LOCK CONTROL - REMOVAL.....23-39
LATCH - REMOVAL.........23-18,23-34,23-51
LATCH - REMOVAL, REAR..............23-40
LATCH - REMOVAL, SAFETY............23-52
LATCH RELEASE CABLE - INSTALLATION . . 23-51
LATCH RELEASE CABLE - REMOVAL.....23-51
LATCH RELEASE HANDLE -
INSTALLATION
.......................23-52
LATCH RELEASE HANDLE - REMOVAL
....23-52
LATCH STRIKER - INSTALLATION
........23-18
LATCH STRIKER - INSTALLATION, REAR
. . 23-41
LATCH STRIKER - REMOVAL
...........23-18
VAINDEX 9
Description Group-Page Description Group-Page Description Group-Page