2005 DODGE SPRINTER Owners Manual

UNDERSTANDING YOUR INSTRUMENT PANEL 97
4
Odometer and Trip MeterActivate the multi-function indicator. The total
distance covered by the vehicle will be shown.
1. To switch between the odometer and the trip meter, press button (1) briefly.
2. To reset the trip meter, call up trip meter. Press
button (1) and hold until the trip meter shows 0000.
NOTE: Odometer and trip meter display– "mi" in USA only.
– "km" in Canada only.
Instrument and Display LightingDisplay lighting:
3. Press button ç, to display lighting dimmer
4. Press button æ, to display lighting brighter

98 UNDERSTANDING YOUR INSTRUMENT PANELInstrument and display lighting:
1. Switch on the marker lamps, refer to "Combination Switch"
2. Press button ç, to instrument and display
lighting dimmer
3. Press button æ, to instrument display lighting
brighter
Outside Temperature Display1. Clock/outside temperature display selector Press button I briefly. The display will switch
to the required mode.
If button I is pressed twice within one second,
the display will revert to the original mode after
20 seconds.

UNDERSTANDING YOUR INSTRUMENT PANEL 99
4
The outside temperature is displayed when the multi-
function indicator is activated. Sudden changes in
temperature, for instance wh en leaving a garage, are
only shown after a certain delay.
NOTE: Outside temperature display
°F in USA only.
°C in Canada only.
Reversing Aid Distance Display (Optional)When the key is in position 2 in the ignition lock and
the reverse gear is engaged, the reversing aid
automatically begins to monitor the area to the rear of
the vehicle.
WARNING!
Even if the display still reads a few degrees above
32
°F (0
°C), the road surface may be icy, particular-
ly in woods or on bridges. You could skid and lose
control over your vehicle and thereby cause an ac-
cident.
Adapt your speed and driving style to the
prevailing road and weather conditions to prevent
an accident and possible personal injury or
property damage.
in

100 UNDERSTANDING YOUR INSTRUMENT PANELThe following display appears if the reversing aid does
not detect an obstacle.
NOTE: Distance display– "in" in USA only.
– "cm" in Canada only.The distance between the sensors and an obstacle
detected within the monitoring range is displayed in
increments of 2 in (5 cm).
If the distance is less than 40 in (100 cm), a warning
signal also sounds, which is repeated increasingly
frequently as the vehicle approaches the obstacle.A continuous warning signal sounds if the distance
undershoots 20 in (50 cm).
When a continuous warning signal sounds for
approximately three seconds and the error code
appears in the multi-function indicator, the reversing
aid is malfunctioning.
Maneuver with particular care, if interference from an
external source of ultrasonic waves (compressed-air
brakes of trucks, a car wash or a pneumatic drill) is
causing the reversing aid to malfunction.
Dirty reversing aid sensors or malfunctioning backup
lamps could also cause the reversing aid to
malfunction. Clean the reversing aid sensors and check
the backup lamps.
Otherwise have the malfunction traced and rectified by
an authorized Sprinter Dealer.

UNDERSTANDING YOUR INSTRUMENT PANEL 101
4
Tachometer (Engine rpm)Do not exceed the maximum permissible engine speed.
NOTE: To protect the engine, its fuel supply is
interrupted when the maximum rpm is reached.
Despite this, the maximum rpm can still be exceeded in
overrun mode (e.g. when driving downhill).
Coolant Temperature GaugeThe coolant temperature is displayed when the key is
in position 2 in the ignition lock.
If corrosion inhibitor/antifreeze is present in the
correct concentration in the coolant, the coolant
temperature will be between 185 °F (+85 °C) and
250 °F (+120 °C), depending on operating conditions.
If the needle reaches the red section, do not continue to
drive the vehicle.

102 UNDERSTANDING YOUR INSTRUMENT PANELFor coolant level indicator lamp /, refer to "Coolant
Level Indicator Lamp".
NOTE: Coolant temperature display
°F in USA only.
°C in Canada only.
CAUTION!
Do not leave your vehicle unattended with the
engine running as you would not be able to react to
the temperature indicator if the engine overheats.
This would lead in turn to engine damage.
WARNING!
Driving when your engine is badly overheated
can cause some fluids which may have leaked into
the engine compartment to catch fire. You could
be seriously burned. Steam from an overheated
engine can cause serious burns and can occur just
by opening the engine hood. Stay away from the
engine if you see or hear steam coming from it.
Turn off the engine, get out of the vehicle and do
not stand near the vehicle until it cools down.

UNDERSTANDING YOUR INSTRUMENT PANEL 103
4
Fuel Gauge with Reserve Fuel Indicator LampThe fuel level is displayed when the key is in position
2 in the ignition lock. The reserve fuel indicator lamp (1) lights up for
about 2 seconds.
If the reserve fuel indicator lamp remains on or lights
up again when the engine is running, the fuel in the
tank hasreached reserve level.
Reserve level: about 2.8 US gal (10.5 liters).
NOTE:
If the fuel gauge sensor is damaged, the reserve
fuel indictor lamp (1) will light up and the needle will
vary its position between the maximum and minimum
marks. Have the malfunction traced and rectified by an
authorized Sprinter Dealer.

104 UNDERSTANDING YOUR INSTRUMENT PANELBattery Charge Indicator LampWhen the key is in position 2 in the ignition lock, the
battery charge indicator lamp # will light up in the
instrument cluster. It must go out when the engine is
running.
If the battery charge indicator lamp # remains on or
lights up again while the vehicle is moving, a fault has
developed in the battery charge circuit.
Do not drive on. Take your vehicle to an authorized
Sprinter Dealer to have the problem corrected.
Water in Fuel Indicator LampWhen the key is turned to position 2 in the ignition
lock, the fuel filter indicator lamp in the
instrument cluster lights up for about 2 seconds. It
must go out when the engine is running.
If water in fuel indicator lamp does not go out or
comes on with the engine running, drain the water
from the fuel filter as soon as possible.