Page 917 of 3870
Fig. 69: Measuring Terminal Voltage Between Special Tool 23
-
Pin Connector Terminal 33 And Ground
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage (approximately 12
volts) when the brake pedal is depressed and 1 volt or less when the brake
pedal is released?
YES : Go to Step 21 .
NO : Go to Step 16.
STEP 16. Check PCM connector B-19 and stoplight switch connector C-03
for loose, corroded or dama
ged terminals, or terminals
pushed back in the
connector.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 928 of 3870
Fig. 78: Connecting Special Tool MB991923
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Turn the ignition switch to the "ON" position.
4. Measure the terminal voltage between special tool 23-pin connector
(without red tape) terminal 33 (PCM connector B-19 terminal 33) and
ground.
When the brake pedal is depressed, the voltage should measure
battery positive voltage (approximately 12 volts). When the brake pedal is released, the voltage should measure 1 volt
or less.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 929 of 3870
Fig. 79: Measuring Terminal Voltage
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage (approximately 12
volts) when the brake pedal is depressed and 1 volt or less when the brake
pedal is released?
YES : It can be assumed that this malfunction is intermittent. (Refer to
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
).
Then go to Step 22 .
NO : Replace the PCM. [Refer to POWERTRAIN CONTROL
MODULE (PCM)
]. Then go to Step 22 .
STEP 21. Using scan tool MB991958, read the diagnostic trouble codes.
1. Connect scan tool MB991958 to the data link connector. (Refer to AUTO
-
CRUISE CONTROL SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY
).
CAUTION: To prevent damage to scan tool MB991958,
always turn the ignition switch to the
"LOCK" (OFF) position before connecting or
disconnecting scan tool MB991958.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 990 of 3870
Fig. 2: Identifying Normal And Abnormal Characteristic Curve
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. If 0 V is indicated at A, there is a break in the positive terminals from A.
Defect where the voltage changes suddenly (12 V) in the same method
described above.
REAR WINDOW DEFOGGER SWITCH REMOVAL AND INSTALLATION Refer to HEATER CONTROL ASSEMBLY AND A/C SWITCH
.
INSPECTION REAR WINDOW DEFOGGER RELAY CONTINUITY CHECK Fig. 3: Identifying Battery Voltage Specification
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor XLS
2004 BODY & ACCESSORIES Rear Window Defogger - Endeavor
Page 1018 of 3870
Fig. 14: Checking Power Window Fuse Voltage
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
POWER WINDOW RELAY CHECK POWER WINDOW RELAY CHECK SPECIFICATION BATTERY VOLTAGE
TESTER CONNECTION
SPECIFIED
CONDITION
Not applied
4-5
Open circuit
Connect terminal
No. 3 and the
negative battery
terminal. Connect terminal
No. 1 and the
positive battery
4-5
Less than 2 ohms
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor
Page 1039 of 3870
< FRONT DOOR > DOOR WINDOW REGULATOR CHECK SPECIFICATION BATTERY CONNECTION
SLIDER POSITION
Connect terminal No. 1 and the
negative battery terminal. Connect terminal No. 2 and the
positive battery terminal.
UP
Connect terminal No. 2 and the
negative battery terminal. Connect terminal No. 1 and the
positive battery terminal.
DOWN
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor
Page 1041 of 3870
Fig. 30: Identifying Door Window Motor Terminals (Rear Door)
negative battery terminal. Connect terminal No. 2 and the
positive battery terminal. Connect terminal No. 2 and the
negative battery terminal. Connect terminal No. 1 and the
positive battery terminal.
DOWN
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor
Page 1045 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
>>B<< LOWER SASH INSTALLATION Securely insert the lower sash into the window rear sash. INSPECTION FRONT DOOR LATCH CHECK The illustration shows when the door lock actuator is viewed from inside the door. DOOR LOCK ACTUATOR INCORPORATED IN DOOR LATCH CHECK < LEFT SIDE> FRONT DOOR LATCH CHECK SPECIFICATION LEVER POSITION
BATTERY
CONNECTION
LEVER OPERATION
At the "UNLOCK"
position
Connect terminal No.
4 and the negative
battery terminal. Connect terminal No.
6 and the positive
battery terminal.
The lever moves from
the "UNLOCK" position
to the "LOCK" position.
At the "LOCK" position
Connect terminal No.
6 and the negative
battery terminal. Connect terminal No.
4 and the positive
battery terminal.
The lever moves from
the "LOCK" position to
the "UNLOCK"
position.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor
