Page 1679 of 3870
Fig. 49: Measuring Voltage Between Terminal 6 And Ground
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Measure the voltage between terminal 16 and ground.
The voltage should measure approximately 12 volts (battery positive
voltage).
Q: Is the measured voltage approximately 12 volts (battery positive
voltage)?
YES: Go to Step 4 .
NO: Go to Step 2.
STEP 2. Check audio amplifier connector C-11 for loose, corroded or
damaged terminals, or terminals pushed back in the connector.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor
Page 1799 of 3870
Fig. 146: Identifying Connector C
-105
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Measure the voltage between terminal number 21 and ground.
The voltage should measure approximately 12 volts (battery positive
voltage).
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor
Page 1800 of 3870
Fig. 147: Measuring Voltage Between Terminal Number 21 And Ground
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the measured voltage approximately 12 volts (battery positive
voltage)?
YES: Either repair or replace the radio and CD player or radio, CD player
and CD changer. Check that a memory is retained.
NO: Go to Step 2.
STEP 2. Check radio and CD player or radio, CD player and CD changer
connector C-105 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor
Page 1831 of 3870
Fig. 6: Disconnecting Connector D
-36
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Ignition switch: ACC
3. The voltage between rear display connector D-36 terminal No.1 and body
ground
OK: Battery positive voltage
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Video Entertainment System - Endeavor
Page 2184 of 3870
Fig. 120: Locating Connector C
-106
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Measure the voltage between terminal 1 and ground.
The measured value should be approximately 12 volts (battery
positive voltage).
Q: Does the measured voltage correspond with this range?
YES:
Go to Step 5 .
NO:
Go to Ste
p 4.
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
Page 2209 of 3870
Fig. 140: Measuring Voltage Between Terminal 1 And Ground
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
The measured value should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approx. 12 volts?
YES:
Go to Step 15 .
NO:
Go to Step 9.
STEP 9. Measure the voltage at A/C compressor clutch relay connector B-
16X.
CAUTION: The top and bottom of the A/C compressor
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
Page 2210 of 3870
1. Disconnect A/C compressor connector B-16X and measure the voltage at
the relay box side.
2. Turn the ignition switch to the "ON" position.
Fig. 141: Locating Connector B
-16X
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Measure the voltage between terminal 2 and ground.
The measured value should be approximately 12 volts (battery
positive voltage).
connector are difficult to identify. Prior to
inspection, confirm the trian
gle mark on the rela
y
box.
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
Page 2217 of 3870
The measured value should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approx. 12 volts?
YES:
Go to Step 13 .
NO:
Go to Step 12.
Fig. 148: Measuring Voltage Between Connector Terminal 1 And Ground
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
STEP 12. Check the wiring harness between A/C compressor clutch relay
connector B-16X
(terminal 1
) and the batter
y.
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
