2004 DACIA SUPERNOVA lock

82A
HORN - ENGINE IMMOBILISER
82A - 27
7. 11 STATE: OPERATE THE RF REMOTE CONTROL / GOOD RF SIGNAL
INDICATION
Do not access the following diagnostic
unless the state 11D
RECOMMENDATION becomes ACTIVE when operating the RF remote control. Check if the keys belong to the vehicle in question.
There is a desynchronising between the code of the RF remote control and the E.C.U. decoder
if at the activation of the remote control, the 111D state remains PASSIVE and the state 11G
becomes AC TIVE for 3 seconds, then becomes PASSIVE. The blocking / unlocking of the
do ors is not possible in this case.
Apply the corresponding procedure of resynchronisation (for one or two keys).
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 28
8. 14G STATE : BLOCKING/ UNLOCKING DOORS
RECOMMENDATION The state 10G (anti starting) must be ACTIVE.
Check the continuity and the isolation related to the +12 V and to the ground of the electric
wiring on the line
E.C.U. decoder Pin B2 pole 1 door locking switch. Pin B5 pole 3
Fix the electric wiring if necessary or replace the switch.
If the incident persists, replace the E.C.U. decoder.
Remove the memorised failure by means of the CLIP tester.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 32
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
(even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHE D OFF.
RECOMMENDATIONCheck if the “Procedure E.C.U. decoder replacement” was correctly
performed.
Check the fuse F15 ( up to 01.06.2001) or
F07 (after 01.06.2001).
Is the fuse good?
Is there the failure “ DOORS’ LOCKING
CONTACT”?
Check the continuity and the isolation related
to the ground, between t he pin A 5 of the
E.C.U. decoder and the dashboard.
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
failure element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder and check if the indicator switches off;
- if the anti starting system is turned off,
c onnect the pin A5 of the wiring connector from
the E.C.U. decoder to an electric ground and
check if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system. Remove by means of the CLIP tester the possibl e memorised failures.
No
No
No
Yes
Yes
No
Yes
YesDIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 35
A
LP6. BLOCKING/UNLOCKING DOORS NOT OPERATING
RECOMMENDATION Check with the CLIP tester the absence of the failures.
If there are memorised failures, these must be removed.
Are the doors blocking mechanisms correctly
operating ?Repair the damaged mechanisms.No
Check the continuity a nd the isolation related to the ground
of the wiring between :
E.C.U . d ecoder pin B8 actuators
Pin B9 doors
Is the wiring in good condition?
Fix the wiring.No
Check the continuity a nd the isolation related
to the ground of the wiring between
E.C.U .pin B8 switch
d ecoder pin B9 blocking doors
Is the wiring in good condition?
Repair.
Di sconnect the E.C.U. decoder, then supply
the wiring connector with +12 V at pin B9 and
the ground at the pin B8, than versa (+ 12 V at
pin B8 and the ground at pin B9).
Ar e the actuators bl ocking/unlocking the
doors?
Damaged actuators.
Replace them.
Replace the E.C.U. decoder, then perform the “E.C.U. decoder replacement
procedure”. No
Yes
Yes
No
YesYes
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 36
A
LP7. UNLOCKING DOORS NOT OPERATING BY RF REMOTE CONTROL
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, these must be repaired.
Are the states 11G and 11D ACTIVE when
the RF remote control is activated?S ee the treatment states 11G and
1 1D cf. Chapter “Diagnostic”.No
Check the fuse F15 ( up to 01.06.2001) or
F 07 (after 01.06.2001).
Is it good?
Replace the fuse.No
Yes
Yes
Activate the doors’ locking switch from t he
dashboard.
Are the doors blocking/ unlocking ? S
ee the treatment of the failure
“Doors blocking contact” and the
state 14 G cf. Chapter “Diagnostic”.
S ee ALP 6.
Yes
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 37
A
LP8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester.
If there are failures, fix them first.
Check if the synchronisatio n of the RF remote control and the E.C.U. decoder has been performed .
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation related to
the ground and the +12 V of the electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalli ng system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F15 ( up to 01.06.2001) or
F 07 (after 01.06.2001).
Is it good?Replace the fuse.
Disconnect the FLASH relay. Supply with
+ 12, the pole 4 of the relay. Are the l eft
turning lights turning on? Supply with +12 V
the pole 5 of the signal relay.
Are the right turning lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 38
No
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
A LP9. THE CEILING LAMP DOES NOT SWITCH ON AT THE BLO CKING /
UNLOCKING OF THE DOORS OR IT REMAINS PERMANENTLY TURNED ON.
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, fix them first.
Check if t he doors are locked?
Has the ceiling lamp turned on? The ceiling lamp was in the
position “p
ermanently
lighting”. Normal
operation.Yes Yes
Unlock the doors with the RF remote control.
The ceiling is in the position “dome lighting”
Has the ceiling lamp turned on?
Check the isolation of the wiring
related to the ground on the line pinA1.
decoder ceiling
After 15 seconds, the ceiling lamp will
turn off.
Normal operation.
Was the E.C.U. decoder confi gured “With
dome ceiling ”?Configure the E.C.U. decoder with
the CLIP tester.
Check the continuity on the line
E. C.U. decoder pin A1 ceiling
Is the line good?Repair .
Check the ceiling lamp bulb.
No
No
No
Yes
Yes Yes
No
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 40
11. Remote control signal reception 11G = activate the RF ACTIVE for 3 secondsremote control decoder receives the
Received signal indication the remote control signal
12. Remote control signal validation 11D = activate the RF ACTIVE for three sec. remote control if the signal received at
Good signal indication the decoder is good
13. Communication doors locking 14G = blocking/ unlocking ACTIVE when the switch E.C.U. decoder E.C.U. decoder receives
control fr om the
doors’ locking switch
14. Co mmunication E.C.U .decoder - 14D =activation of the doors ACTIVE doors when
doors ac tuators actuators the E.C.U. decoder
sends the command
blocking/unlocking to
the actuators of the
doors.
15. The state of the doors contact 16G = doors contact ACTIVE when the front doors are opened.
NOTE: the state
ACTIVE occurs also
if front hood or hatchback
are opened when the
vehicle is equipped
with anti intrusion system
16. Remote controls synchronisation in 17G =programming in progress ACTIVE when the process or resynchronisation TIR/ TRF remote control
resynchronisation
procedure is in pr ocess
17. RF remote controls synchronisation 17D = not performed TIR ACTIVE when the
not perfor med programming remote control
synchronisation is not
performed.
18. Not performe d key code programming 19G = unperformed key ACTIVE when the
programming key programming is
not pe rformed
19 . Validated key code programming 19D = unblocked key programmi ng ACTIVE when the
validation of the key
programming is not
performed
20 . Th e pr og ramming of the first key 18G = the memorising of the ACTIVE when the
first key programming of the
fir st key is in process
DIAGNOSTIC
vnx.su