2004 DACIA SUPERNOVA lock

82B
HORN - ENGINE IMMOBILISER
82B - 42
The anti intrusio
n system may be activated or deactivated by pushing the button of the RF remote
control of the vehicle key and it is achieving the peripheral protection of the vehicle and the volumetric
protectio n of the cockpit. The activation of the system is indicated on the instru ment panel by the LED
indicator, which will start to blink, and is confirmed by two blinks of the turning lights. Deactivation is
confirmed by a blink of the turning lights and LED indicator switching off.
In case of the vehicles equipped with central locking system, the doors will lock when the system
is activated and will unlock when deactivating the anti intrusion system. After 40 seconds from
remote control activatio n, the opening of a door, of the hood or the hatchback will cause the siren
starting and turning lights blinking for 30 seconds; after 30 seconds, the system remains activated.
During those 40 seconds, the volumetric sensors will “read” the volume of the cockpit, this
“reading” being reinitialised on every activation of the system, in order to take into account the
potential volume modifications. Any modifications of the inner volume of the cockpit ( broken
w indow glass, intrusion in the cockpit or movement inside the cockpit) will perturb the ultra-
sound emission field causing the siren starting.
The system does not normally operate unless all doors, the engine hood, the hatchback and
the window glasses are properly closed. If one of the front doors, the engine hood or the hatchback
is not well c losed, at the doors locking with the RF remote c ontrol, the t urning lights will not
switch on at all. At the deactivation with RF remote control, the traffic indicators will switch on,
just once.
AT TENT ION
In case of one door opening by key, while the anti intrusion system is
activated, the siren will start and it can be stopped by pressing the remote button or by
introducing the PIN code which is written on the vehicle invoice.
SY STEM FUNCTIONNING
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 43
THE PIN CODE
The PIN code is formed of four figures and it can be used only for deactivating the anti intrusion
s ystem, if this operation can not be performed by pushing the deactivating button from the RF
remote control of the vehicle. For introducing the PIN code, perform as follows:-set on the contact key in the M position and take it off it for three times in seven seconds,
after which the anti intrusion LED indicator will switch on for three seconds; -set on the contact again on the M position and maintain it until the number of the L ED
blinks is e qual with the first figure of the PIN code, then take off the contact; -set on the contact in the M position and maintain it until the number of LED blinks is equal
w ith the second figure of the PIN code, then take off the contact;
-perform the above mentioned method in order to introduce the third and the fourth figure
of the PIN code;
-after that, the system is deactivated and the siren stops automatically;
- set on the contact again – the anti LED indicator must switch on, confirming in this way
that the c orrect introduction of the PIN code.
AT TENT ION
If it i s necessary the checking of the PIN code, t his will be pe rformed
only after al least 20 seconds have passed, since the anti intrusion ECU has been
connected to the vehicle’s wiring or since the connecting of t he vehicle’s battery.
The COBRA anti intrusion system can operate in t hree different modes (2,3 or 4).
For the Super Nova vehicles, the system has been programmed to work in the second operation
mode. If by mistake the PIN code was introduced in less than 20 seconds since the battery
connecting or since connecting the anti intrusion ECU, this can involve the change of the operation
way of the system, which will generate errors during the operation. There is, although, the possibility
of reprogramming the correct operation way (type 2) and in this purpose, perform the following
operations : - disconnect and then reconnect the anti intrusion ECU; when connecting the anti intrusion
ECU the anti intrusion LED indicator will switch on once, confirming the correct connecting;
-af ter at least 5 seconds from the previous operation, but no more than 20 second from it,
perform the following operation s:
-s et on the contact key in the M position for three times and then release it;
- the anti intrusion LED indicator will switch on for three seconds and then will switch off;
- set on again the contact key in the “M” position and maintain it, counting two blinks of the
anti intrusion LED indicator, then take off the contact;
- the LED indicator will blink for two times in two series, confirming in this way the proper
performance of the previous operations;
press the doors locking button of the dashboard, in order to lock and unlock the doors; the anti
intrusion LED indicator must not blink;
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 44
This cycle indicating the aggression type, stops after setting on the contact.
THE SYSTEM’S MEMORY
If after the deactivating command of the system, the turning lights will blink four times and a
sound will be heard also four times, this proves that previous the deactivating, an active cycle of
the system has t aken place and the reason for it will be shown by the LED indicator as follows:
TEMPORARY CANCELLING OF THE VOLUMETRIC PROTECTION
In case you want to let a window glass partially opened or a passenger remains in the vehicle,
it is possible to temporary cancel the volumetric protection function, but the peripheral protection
remains active. Proceed as follows:
- set on the contact key in the M position and then take it off, in no more than seven
seconds; - get off the ve hicle a nd press once the button of the remote c ontrol, in no more t han 20
seconds. The volumetric protection is again active after the next locking of the doors using the remote
control.
LED indicator
1 blink
3 blinks
4 blinks
8 blinksCause
Engine hood, door or hatchback opening
V olumetric detection
St arting attempt detected
Errant communication with the siren
-get off the vehicle and press the button of the RF remote control – the doors of the vehicle
will lock and the anti intrusion indicator will start blinking, confirming that the anti intrusion system
is activated; -press again the button of the RF remote – the doors will unlock and the anti intrusion LED
indicator must switch off.
THE SYSTEM’S MEMORY
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 45
Vo l u m etric protection checking.
Perform the following checking steps after locking using the RF remote control, the doors, the
engine hood and the hatchback. The operations must be performed in no more than 40 seconds
since the anti i ntrusion system has been activated with the RF remote control; if operating after
these 40 seconds, the siren will start and the turning lights will blink.
Close the door. The sound signal (buzzer)
will stop.
Th e pr oper operation of the anti intrusion system on different situations must be according to
those shown in Table 01. For detecting the causes of possible incidents of the anti intrusion system, perform the checking
steps presented in Table 02.
Lo wer the rear windows with about 10
cm. Close the doors, the engine hood
and the ha tchback.
Check out if there is any movement in
the cockpit.
Ac tivate the system pressing the button
of the RF remote control.
In troduce a hand through the window,
inside the cockpit and move it.
Th e LED indicator will blink quickly,
showing there has been a volumetric
detection and that volumetric sensors are
f unctioning correctly.
Deac tivate the system using the RF
remote contro l, then clos e al l the
vehicle windows.
Reactivate the system and then hit by
ha nd the windows surfa c e of the
vehicle. The LED indicator should
continue to normally blink and the siren
starting shall not occur.
Functional checking of the peripheral
protection.
Close the doors, the engine hood and the
hatchback.
Ac tivate the system pressing the button
of th e RF remote.
The doors will lock and the LED indicator
will blink.
Open a do or with the vehicle key.
The LED indicator will continuously be on,
a nd a sound signal (buzzer) will be heard.
Deac tivate and reactivate the sys tem
w ith the RF remote control.
Deac tivate t he system by pressing the
button of the RF remote control.
The do ors will unlock and t he LED
indicator will go off.
Rep eat a.m. operations for both front
door s, engine hood and hatchback.
FUNCTIONAL CHECKING OF THE SYSTEM
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 51
If after a complete checking of the anti intrusion system,
the replacement of the E.C.U. anti
intrusion is required, proceed as follows:
- remove from the central console the tape recorder’s frame and the tape recorder pulling
backward but without disconnecting the tape recorder from the vehicle’s wiring;
- dismount by detaching the aeration grill located on the right side of the central console ;
- dismount the t wo screws attaching t he E CU support i n t he ri ght side of the climate
control unit;
- take off the anti intrusion ECU together with its support through the central zone of the
central console; - disconnect the 24 ways connector from the anti intrusion ECU proceeding as follows:
remove towards exterior the two blocking clips of the connector and then carefully pull out the
connector; - dismount carefully the two way connector from the anti intrusion ECU;
- dismount the two screw attaching the anti intrusion ECU on its support;
- proceed the in reverse order of the dismounting;
- check the proper operation of the anti intrusion system. DISMOUNTING – REMOUNTING
OF THE ANTI INTRUSION ECU
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 52
If siren dismounting is required, proceed as follows:
- dismount the two attachment nuts of the siren on its support;
- pull carefully the blocking clip of the wire connector to the siren and then disconnect the
siren;
- connect to the siren the connector of the wiri ng, by pushing, until you hear a “click”
confirming the correct c onnecting, then mount the two attachment screws of the siren on the
support;
- check the proper operation of the anti intrusion system. SIR
EN DISMOUNTING –REMOUNTING
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 53
The engine hood connector is dismounted as follows:
- easy pull the blocking clip of the wirin g connector and then disconnect the engine hood contact;
- press the blocking clips of the lateral sides of the contact;
- push upward the contact i n order to remove it from its place.
Mount the new contact in its support by downward pushing, until a “click” is heard, confirming
the correct connecting. Connect the wires connector to t he contact of the hood.
Check the proper operation of the hood contact and of the anti intrusion system. DISMOUNTING – REMOUNTING OF THE HOOD CONTACT
vnx.su

84
CONTROLS - SIGNALLING
84 -1
(STARTING – IGNITION SWITCH)
The anti theft mechanism is placed on the right part of the steering column and has the purpose
to starter control when electric system is connected, being provided in the same time also with a
steering locking device, with anti theft lock.
NOTE
At the anti theft mechanism there is not any more marked G position (garage) because
it does not allow the taking out of the key in this position but helps in pi n unblocking
for removing the mechanism from the steering column.
Disconnect the battery.
Dismount the steering wheel casings.
Disconnect the anti-starting bushing.
Remove the bushing off the steering column.
Disconnect the switch connection wires.
B ring the key in the interme diary position (ex G).
Dismount the attachment screw (1).
P ush the mobile pin ( 2) and pull backwards
the switch.
REMOUNTING
Mount the switch in its place.
Tighten the attachment screw(1).
Connect :
- the switch
- the battery.
Position and mount the anti-star ting bushing.
Connect the anti-starting bushing to the ve-
h icle wirin g.
Check the switch operation.
Mount the steering wheel casings. DISMOUNTING
ANTI THEFT MECHANISM
vnx.su