2004 DACIA SUPERNOVA brakes

VALUES AND SETTINGS
07BRAKES
Vehicle
DACIA
SupeRN ova Normal
20 Minim
19 Normal
228 Maxim
229 Front
0,1 Rear
-
The width of brake disk and drums diameter (mm)
Front Rear The maxim axial run out
of disk
Vehicle
DACIA
SupeRN ova Normal
14 Minim
7 Normal
5 Minim
0,5 mm
above the r ivets SA
EJ 1703 DOT 4
The thickness of gaskets (mm)
Front Rear Brake fluid
07 - 7
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 57
DIAG
NOSING-INTERPRETING THE STATES
The idle mode rotation
ra tio > maximal limit. The id
le mode rotation ratio is too great.
- Chec k the oil level of the engine
- Chec k the good functioning of the atmospheric pressure sensor.
- Check the tubes connected to the admission collector.
-C heck the fittings of the admission collector
- Check the watertightness fittings of the clapper body
- Check the watertightness of the power-brakes.
- Chec k the presence of the nozzles of the oil-vapour re-aspiration circuit
- Chec k petrol pressure.
- Check the adjustment of the rocker-arms and the settling of the distribution.
If all the above are correct, then the step-by-step engine will have to be replaced.
Perform again the conformity test
AF T E R REPAIR
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 68
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
A
Check if there are cases of lack of watertightness (noise)
on the powe r-brakes.
Connect the “CLIP TEHNIC” device to do this test in
accordance with the usual manner of work.
Disconnect the tube between the draining valve and the
intake collector and strangle it up. If the disturbances
d isappear, the cause was the draining valve.
AFTER REPAIR Erase the def
ects memorized. If there are no other problems,
eras e the parameters memorized by the calculator.
Check the powe r -br a kes
Ch eck t h e engine compression
♦
♦
Check the canister
draining valve♦
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 70
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
Check if the clapper body is not clogged.
Check if there are cases of lack of watertightness (noise)
on the powe r-brakes.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Check if the spurs, the brake cylinders and the wheel ball-
rings are no t seized-up.Check the body o f
the clapper♦
Ch eck t he power-br akes
Check the engine
flywheel
Check the running
train
Check the cooling
of the engine
♦
♦
♦
Check if there is enough engine cooling.♦
Check the canister
draining valve Disconnect the tube between the draining valve and the in-
take collector and strangle it up. If the disturbances disap-
pear, the caus
e was the draining valve.
Check the engine
comp ression Connect the “CLIP TEHNIC” device to do this test in accor-
dance w ith the usual manner of work.
AFTER REPAIR Erase the defec
ts memorized. If there are no other problems,
eras e the parameters memorized by the calculator.
♦
♦
A
vnx.su

30
GENERAL
30 - 11
BRAKING SYSTEM DIAGNOSTIC
II.
CONSTANT EFFECT AT BEHAVIOUR
EFFECTS
Brakes not accomplishing the
required braking distance
Vibrating brakes
When braking, the vehicle ( front
p art) is left/right deviating
Braking
Heating brakes POSSIBLE CAUSES
- No n- un if o rm wo rn brake lin ings
(backing off);
- Brake linings slightly greased;
- Springs with modified characteristics.
- Brake disks with high wobbling;
- Inconstancy brake disks width;
- Particles abnormal deposit on brake disks
(oxidation between linings and disk).
- Front axl e suspension, steering (to be
checked);
- Stuck piston;
- Tires – wear, inflati on pressure;
- Rigid duct narrowed (flattening).
- Stuck piston;
Automatic adjustment : hand brake cable very
tighten.
REMARK :
Automatic recovering is performed by
means of the brake pedal, if there is no ab-
no rm al t ensi on in the hand brake cable
when released (hand brake released).
- Return spring.
- Insufficient hydraulic stroke of the brake
pump, not allowing the return at rest of
the brak e pump pistons ( brake pump
remaining under pressure);
- Stuck pistons or hardly returning;
- Rigid duct narrowed (flattening);
- Def ective adjustment of the hand brake
control.
vnx.su

30
GENERAL
30 - 13
BRAKE FLUID
PERIODICITY OF THE BREAK FLUID CHANGE
The manufacturing conception of the brakes equipping the Dacia vehicles, especially
the di sks brake type (F 54 inner empty pistons, low qua ntity of fluid in t he c ylinders,
sliding calipers avoiding existence of a fl uid reserve in the less cooled area of t he wheel)
enable t he m aximum re jection of fluid vapori zation ri sk, even in c ase of intensive using of
brakes (mountain are a). The current bra ke fluids are subject in all cases to a slight degradation during the fi rst
months of use by a slight humidity absorpt ion seri es (see the Vehicle Warra nty and
Maintenance Booklet, for brake fluid change)
LEVEL COMPLETION
The wear of brakes pads and shoes generate a gradually diminution of brake fluid level
in its reservoi r. It is useless t o compensate t his diminution, because the level will be re -
stored in the moment of next changing the brake pads and shoes. Obviously, in the mean-
time, the level of brake fl uid in re servoir must not go down bellow the minimal mark.
HOMOLOGATED BRAKE FLUIDS
The mixture i n t he bra king circuit of two non compatible brake fluids may leads to loss
important risks mainly due to gasket damage
In order t o avoid such risks, it is obligatory t o use bra ke fluids checked and approved by
our laboratories and which are accordi ng to Norm SAEJ 1703, DOT 4.
vnx.su