2002 ISUZU AXIOM air condition

RESTRAINT CONTROL SYSTEM 9J1±32
5. This test determines whether the malfunction is in
CKT IB06±YEL/BLK.
6. This test determines whether the malfunction is in
the SRS coil assembly or the driver air bag
assembly.Diagnostic Aids:
An intermittent condition is likely to be caused by a short
to ground in the driver air bag assembly circuit. Inspect
CKTs IB05±YEL and IB06±YEL/BLK carefully for cutting
or chafing.
DTC 24 Driver Deployment Loop Short To Ground
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Ignition switch ªOFF.º
3. Connect scan tool data link connector. Follow directions as
given in the scan tool operator's manual.
Ignition switch ªON.º
4. Read driver sense LO.
Is driver sense LO less than 1.5 volts?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Disconnect SRS coil assembly yellow 2±pin connector located
at base of the steering column. Leave passenger air bag
assembly connected.
3. Connect SRS driver / passenger load tool J±41433 and
appropriate adapter to SRS coil assembly harness connector.
4. Ignition switch ªON.º
Is DTC 24 current?
Go to Step 4 Go to Step 6
41. Ignition switch ªOFF.º
2. Disconnect SDM.
3. Disconnect SRS driver / passenger load tool.
4. Measure resistance on SDM harness connector ª3º to terminal
ª6º (ground).
Does J±39200 display ª0Lº (infinite)?
Go to Step 5
Replace SRS
harness.
Go to
Step 7
5Measure resistance on SDM harness connector from terminal ª4º
to terminal ª6º (ground).
Does J±39200 display ª0Lº (infinite)?
Go to Chart A .
Replace SRS
harness.
Go to
Step 7
61. Ignition switch ªOFF.º
2. Disconnect SRS driver / passenger load tool J±41433 from
SRS coil assembly harness connector.
3. Connect SRS driver / passenger load tool J±41433 and
appropriate adapter J±35616±A to driver air bag assembly
harness connector. Located top of the steering column.
4. Reconnect SRS coil assembly harness connector as the base
of steering column.
5. Ignition switch ªON.º
Is DTC 24 current?
Ignition switch
ªOFF.º
Replace SRS coil
assembly.
Refer to in this
section 9J±24.
Go to
Step 7
Ignition switch
ªOFF.º
Replace driver air
bag assembly.
Go to
Step 7
71. Reconnect all components, ensure all component are properly
mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 7

9J1±33
RESTRAINT CONTROL SYSTEM
DTC 25 Driver Deployment Loop Short To Voltage
D09R200001
Circuit Description:
When the ignition switch is turned ªONº, the SDM will
perform tests to diagnose critical malfunctions within
itself. Upon passing these tests, ªignition 1º, and
deployment loop voltages are measured to ensure they
are within their respective normal voltage ranges.
The SDM monitors the voltage at ªDriver Bag Lowº
terminal ª4º and ªPassenger Bag Lowº terminal ª16º to
detect shorts to B+ in the air bag assembly circuits.
DTC Will Set When:
ªIgnition 1º is in the normal operating voltage range. This
test is run once each ignition cycle and ªContinuous
Monitoringº. Once these conditions are met and the
voltage at ªDriver Bag Lowº is above a specified value,
DTC 25 will set.
Action Taken:
SDM turns ªONº the ªAIR BAGº warning lamp and sets
DTC 25 and also DTC 71
DTC Will Clear When:
The SDM is replaced.
DTC Chart Test Description:
Number(s) below refer to step number(s) on the
diagnostic chart:
2. This test determines whether the SDM is
malfunctioning.
3. This test isolates the malfunction to one side of the
SRS coil assembly yellow 2±pin connector at the
base of steering column.
4. This test determines whether the malfunction is in
CKT IB05±YEL.
5. This test determines whether the malfunction is in
CKT IB06±YEL/BLK.

RESTRAINT CONTROL SYSTEM 9J1±34
6. This test determines whether the malfunction is in
the SRS coil assembly or the driver air bag
assembly.
Diagnostic Aids:
An intermittent condition is likely to be caused by a short
to B+ in the driver air bag assembly circuit. Inspect CKTs
IB05±YEL and IB06±YEL/BLK carefully for cutting or
chafing. If the wiring pigtail of the driver air bag assembly
and SRS coil assembly is damaged, the components
must be replaced. A careful inspection of CKT IB05±YEL
and IB06±YEL/BLK, including the SRS coil assembly and
driver air bag assembly is essential to ensure that the
replacement SDM will not be damaged.

9J1±35
RESTRAINT CONTROL SYSTEM
DTC 25 Driver Deployment Loop Short To Ignition
CAUTION: When DTC 25 has been set, it is necessary to replace the SDM. Setting DTC 25 will also cause DTC
71 to set. When a scan tool ªCLEAR CODESº command is issued and the malfunction is no longer present,
DTC 71 will remain current. Ensure that the short to voltage condition is repaired prior to installing a
replacement SDM to avoid damaging the SDM.
Step
ActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Ignition switch ªOFF.º
3. Connect scan tool data link connector. Follow directions as
given in the scan tool operator's manual.
4. Ignition switch ªON.º
5. Read driver sense LO.
Is driver sense LO more than 3.5 volts?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Disconnect SRS coil assembly yellow 2±pin connector at the
base of the steering column. Leave passenger air bag
assembly connected.
Connect SRS driver / passenger load tool J±41433 and
appropriate adapter to SRS coil assembly harness connector.
3. Ignition switch ªON.º
Is driver sense LO more than 3.5 volts?
Go to Step 4 Go to Step 6
41. Ignition switch ªOFF.º
2. Disconnect SDM.
3. Disconnect SRS drive / passenger load tool.
4. Measure resistance on SDM harness connector from terminal
ª3º to terminal ª12º (Ignition 1).
Does J±39200 display ª0Lº (infinite)?
Go to Step 5
Replace SRS
harness.
Go to
Step 7
5Measure resistance on SDM harness connector from terminal ª4º
to terminal ª12º (Ignition 1).
Does J±39200 display ª0Lº (infinite)?
Go to Chart A .
Replace SRS
harness.
Go to
Step 7
61. Ignition switch ªOFF.º
2. Connect SRS driver / passenger load tool J±41433 and
appropriate adapter J±35616±A to driver air bag assembly
harness connector located of top of the steering column.
3. Reconnect SRS coil assembly harness connector as the base
of steering column.
4. Ignition switch ªON.º
Is driver sense LO more than 3.5 volts?
Ignition switch
ªOFF.º
Replace SRS coil
assembly.
Go to
Step 7
Ignition switch
ªOFF.º
Replace driver air
bag assembly.
Go to
Step 7
71. Reconnect all components, ensure all components are
properly mounted.
2. Ignition switch ªON.º
Is passenger sense LO less than 3.5 volts?
Replace SDM.
Go to
Step 8 Go to Chart A .
81. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 8

9J1±37
RESTRAINT CONTROL SYSTEM
2. This test verifies proper connection of the yellow
2±pin connector at the base of the steering column.
3. This test checks for proper contact and/or corrosion
of the yellow 2±pin connector at the base of the
steering column.
4. This test isolates the malfunction to one side of the
SRS coil assembly yellow 2±pin connector located
at the base of steering column.
5. This test determines whether the open is in the
wiring.
6. This test determines whether the malfunction is in
the SRS coil assembly or the driver air bag
assembly.
Diagnostic Aids:
An intermittent condition is likely to be caused by a poor
connection at the driver air bag assembly harness 2±pin
connector terminals ª1º and ª2º at the top of the steering
column, SRS coil assembly harness 2±pin connection
terminals ª1º and ª2º, SDM terminals ª3º and ª4º, or an
open in CKTs IB05±YEL and IB06±YEL/BLK.

9J1±45
RESTRAINT CONTROL SYSTEM
DTC 71 Internal SDM Fault
D09R200001
Circuit Description:
DTC 71 is an indication of a potential internal SDM
malfunction and will set if any of the following conditions
are detected:
1) Deployment or microprocessor energy reserve failure.
2) EEPROM failure.
3) ROM failure.
4) RAM failure.
5) Calibration check sum failure.
6) Deployment switch faults.
7) Accelerometer fault.
8) Arming sensor fault.
9) Diagnostic current faults.
10) DTC 19
11) DTC 25
12) DTC 51
13) DTC 53
DTC Will Set When:
Any of the above indicated malfunctions are detected by
the SDM. The malfunctions described above are tested
mainly during ªContinuous Monitoringº and some ones
run each ignition cycle.
Action Taken:
SDM turns ªONº the ªAIR BAGº warning lamp and sets a
diagnostic trouble code.
DTC Will Clear When:
A scan tool ªClear Codesº commanded is received by the
SDM. Some of the indicated malfunctions will only allow
the ªAIR BAGº warning lamp to go out.
But when DTC 19, 25, 51, 53 are also set, SDM is
Replaced.

RESTRAINT CONTROL SYSTEM 9J1±46
DTC 71 Internal SDM Fault
WARNING: DURING SERVICE PROCEDURES. BE VERY CAREFUL WHEN HANDLING A SENSING AND
DIAGNOSTIC MODULE (SDM). NEVER STRIKE OR JAR THE SDM. NEVER POWER UP THE SRS WHEN THE
SDM IS NOT RIGIDLY ATTACHED TO THE VEHICLE. ALL SDM AND MOUNTING BRACKET FASTENERS MUST
BE CAREFULLY TORQUED AND THE ARROW MUST BE POINTING TOWARD THE FRONT OF THE VEHICLE
TO ENSURE PROPER OPERATION OF THE SRS. THE SDM COULD BE ACTIVATED WHEN POWERED WHILE
NOT RIGIDLY ATTACHED TO THE VEHICLE WHICH COULD CAUSE DEPLOYMENT AND RESULT IN
PERSONAL INJURY.
CAUTION: When DTC 19 or 25 or 51 or 53 has been set it is necessary to Replace the SDM. Setting DTC 19 and
25 or 51 or 53 will also cause DTC 71 to set. When a scan tool ªCLEAR CODESº command is issued and the
malfunction is no longer present, DTC 51 or 53 and DTC 71 will remain current. Ensure that the short to voltage
condition DTC 19, 25 is repaired prior to installing a Replacement SDM to avoid damaging the SDM.
Step
ActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
2Confirm SRS ªDiagnostic System Check.º
Is DTC 19 or 25 or 51 or 53 also set (current or history)? (Refer to
notice above).Go to DTC 19 if
DTC 19 is set.
Go to
DTC 25 if
DTC 25 is set.
Go to
DTC 51 if
DTC 51 is set.
Go to
DTC 53 if
DTC 53 is set.
Ignition switch
ªOFF.º
Replace SDM.
Repeat the ªSRS
Diagnostic
System Check.º