2001 TOYOTA SEQUOIA battery

I05476
2
1
I054772
1
I153572
1
I153582
1
I15353
2
1
BE±70
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
3474 Author: Date:
2005 SEQUOIA (RM1146U)
5. Passenger 's Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the power window mo-
tor.
NOTICE:
Since the jam protection may not work properly, be sure to
conduct procedures described in ºHOW TO RESET POW-
ER MOTOR (RESET AND PULSE SWITCH)º after this in-
spection.
6. Rear Right Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminals 2, and check that
the motor turns clockwise.
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the power window mo-
tor.
7. Rear Left Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2, and check that
the motor turns clockwise.

I15354
2
1
I14317
21
I1431821
I21531
21
I21532
21
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE±71
3475 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the power window mo-
tor.
8. Front Door:
INSPECT PTC OPERATION
(a) Disconnect the connector from the wire harness side con-
nector.
(b) Connect the negative (±) lead from the ammeter to termi-
nal 1 of the motor side connector and the positive (+) lead
to negative terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal
2 of the motor side connector, and raise the window to the
fully closed position.
(d) Continue to apply voltage and check that the current
changes from approximately 14 A to less than 1 A within
4 to 90 seconds.
(e) Disconnect the leads from the terminals.
(f) Approximately 90 seconds later, connect the positive (+)
lead from the battery to terminal 1 and the negative (±)
lead to terminal 2, and check that the window begins to
goes down.
If operation is not as specified, replace the power window mo-
tor.
9. Rear Door:
INSPECT PTC OPERATION
(a) Disconnect the connector from the wire harness side con-
nector.
(b) Connect the negative (±) lead from the ammeter to termi-
nal 1 of the motor side connector and the positive (+) lead
to negative terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal
2 of the motor side connector, and raise the window to the
fully closed position.
(d) Continue to apply voltage and check that the current
changes from approximately 14 A to less than 1 A within
4 to 90 seconds.
(e) Disconnect the leads from the terminals.
(f) Approximately 90 seconds later, connect the positive (+)
lead from the battery to terminal 1 and the negative (±)
lead to terminal 2, and check that the window begins to
goes down.
If operation is not as specified, replace the power window mo-
tor.

BE2MM±01
I18616
I18690
2
3 1DOWN UP
I27714
I27715
± BODY ELECTRICALBACK DOOR POWER WINDOW CONTROL SYSTEM
BE±75
3479 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT BACK DOOR POWER WINDOW SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
UP3 ± 6Continuity
OFF±No continuity
DOWN3 ± 5Continuity
If continuity is not as specified, replace the switch.
2. INSPECT BACK DOOR KEY LOCK AND UNLOCK
SWITCH CONTINUITY (Back Door Control Switch)
Switch positionTester connectionSpecified condition
UP1 ± 3Continuity
OFF±No continuity
DOWN2 ± 3Continuity
If continuity is not as specified, replace the switch.
3. INSPECT BACK DOOR POWER WINDOW MOTOR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 4 and check that
the motor turns clockwise.
(b) Connect the positive (+) lead from the battery to terminal
4 and the negative (±) lead to terminal 1 and check that
the motor turns counterclockwise.
If operation is not as specified, replace the back door power
window motor.

BE2MN±01
± BODY ELECTRICALBACK DOOR POWER WINDOW CONTROL SYSTEM
BE±77
3481 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. RESET (INITIALIZE) POWER WINDOW REGULATOR MOTOR
NOTICE:
Resetting the power window regulator motor (initializing the pulse sensor) is necessary if: 1) the bat-
tery terminal cable is disconnected; 2) the back door ECU, wire harness, power window regulator
switch, power window regulator assembly and power window regulator motor are replaced or re-
moved/installed; or 3) the P/W fuse is replaced or removed. If resetting is not performed, the master
switch assembly will not be able to operate the AUTO operation function, jam protection function and
remote operation function.
(a) Turn the ignition switch ON.
(b) Open the power window halfway by pressing the power window switch.
(c) Fully pull up on the switch until the power window is fully closed and continue to hold the switch for
at least 1 second.
(d) Check that the AUTO UP/DOWN function operates normally.
If the AUTO UP/DOWN function operates normally, reset operations are complete. If abnormal, follow the
steps (e) to (g) below.
(e) Disconnect the negative battery terminal cable for 10 seconds.
(f) Connect the battery terminal cable.
(g) Perform the steps (a) to (d) again.

I04138
1 21 2
I04139
5 65 6
I04140
1 21 2
I04141
3 43 4
I04141
3 43 4
BE±80
± BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
3484 Author: Date:
2005 SEQUOIA (RM1146U)
6. INSPECT DRIVER'S DOOR LOCK MOTOR OPERA-
TION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2, and check that
the door lock cable moves to the UNLOCK position.
(b) Reverse the polarity and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock motor.
7. INSPECT PASSENGER'S DOOR LOCK MOTOR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
5 and the negative (±) lead to terminal 6, and check that
the door lock cable moves to the UNLOCK position.
(b) Reverse the polarity and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock motor.
8. INSPECT REAR LEFT SIDE DOOR LOCK MOTOR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2, and check that
the door lock cable moves to the UNLOCK position.
(b) Reverse the polarity and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock motor.
9. INSPECT REAR RIGHT SIDE DOOR LOCK MOTOR
OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative (±) lead to terminal 4, and check that
the door lock cable moves to the UNLOCK position.
(b) Reverse the polarity and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock motor.
10. INSPECT BACK DOOR LOCK MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative (±) lead to terminal 4, and check that
the door lock cable moves to the UNLOCK position.
(b) Reverse the polarity and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock motor.

Disarmed state
Perform any of the following and the system will go on to ºArming preparationº:

With all the doors, the engine hood and the back door closed, lock all doors with the key.

With all the doors, the engine hood and the back door closed, lock all doors by the
wireless remote control.

With all the doors, engine hood and back door locked, open and close any of the doors, the
engine hood or the back door, then close and lock all doors, the engine hood and the back door.
Arming preparation
Perform the following and the system will
go on to ºArmed stateº:

Let 30 seconds elapse with all the doors,
engine hood and the back door closed and
locked.
Perform any of the following and the system
will return to ºDisarmed stateº:

Open any of the doors, the engine hood or
the back door .

Unlock any of the doors or the back door.

Put the key in the key cylinder.

Reconnect the battery.
Armed state
Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors or the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
Perform any of the following and the system
will go on to ºAlarm soundingº:

Open any of the doors or the back door.

Unlock any of the doors or the back door in
any way other than with a key or by the wireless
remote control.

Open the engine hood.

Reconnect the battery.

When input from the optional glass break sensor
is detected (Dealer option).(Key not inserted in key cylinder.)
Alarm sounding
The vehicle's horn and security horn will sound,
and the hazard, interior, tail and head lights come
on for 60 seconds.
After the alarm has stopped, the system will
return to ºArmed stateº. Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors and the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±83
3487 Author: Date:
2005 SEQUOIA (RM1146U)
2. ACTIVE ARMING MODE

Perform any of the following and the system will go to disarmed state (B):

Turn the key from IG to OFF and remove the key from the ignition, open the driver's door.
Disarmed state (A)
Perform any of the following and the system
will return to disarmed state (A):

Push the unlock switch on the transmitter.

Put the key in the key cylinder.

Reconnect the battery.

Turn the ignition from OFF to ON.

Unlock any of the doors or back door with
the key.Disarmed state (B)Perform the following and the system will go
to arming preparation:

Close all the doors, hood and
back door.
Perform any of the following
and the system
will return to disarmed state
(B):

Open any of the doors, the
hood or the back door.
Arming preparation
Perform the following and the
system will go to armed state:

Allow 30 seconds to elapse
with all the doors, hood and
back door closed.
Perform any of the following and
the system
will return to disarmed state (A):

Push the unlock switch on the
transmitter.

Put the key in the ignition.

Reconnect the battery.

Turn the ignition from OFF to
ON.

Unlock any of the doors or back
door with the key.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±85
3489 Author: Date:
2005 SEQUOIA (RM1146U)
3. PASSIVE ARMING MODE
This mode can be switched by the C±BEST customizing
function (See page DI±1684).
All modes are initially set to active when shipped from fac-
tory (no passive mode).

Perform the following and the system will return
to armed state:

Allow the alarm sounding period to pass.
Alarm sounding
Perform any of the following and the system will
return to disarmed state (A):

Push the unlock switch on the transmitter.

Put the key in the key cylinder and turn it ON.

Unlock any of the doors or the back door
with the key.
Perform any of the following and the system will
return to disarmed state (A): *

Push the unlock switch on the transmitter.

Put the key in the key cylinder and turn it ON.

Unlock any of the doors or the back door
with the key.
Armed state
Perform and/or detect any of the following
and the system will go on to alarm sounding:

Open any of the doors or the back door and
allow the entry delay time to pass.

Open the hood.

Reconnect the battery.

Ignition switch is connected directly.

Broken window glass.
BE±86
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
3490 Author: Date:
2005 SEQUOIA (RM1146U)