2001 TOYOTA SEQUOIA terminal TC

± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1759
1953 Author: Date:
2005 SEQUOIA (RM1146U)
Illumination circuit
CIRCUIT DESCRIPTION
The body ECU and the back door ECU detect the condition of each door courtesy light switch.
FRONT COURTESY LIGHT SWITCH CONTROL:
The 2 front courtesy light switches are directly connected to the body ECU and back door ECU. If the courte-
sy light switch is turned on (a front door is opened), voltage applied to terminal ILE of the body ECU is
grounded inside the ECU and the step light, front courtesy light, etc. come on.
REAR COURTESY LIGHT SWITCH CONTROL:
The 2 rear courtesy light switches are directly connected to the body ECU and back door ECU via each cour-
tesy light. The rear courtesy light comes on when a rear door is opened.
DID9B±01

DI±1770
± DIAGNOSTICSBODY CONTROL SYSTEM
1964 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check remote control mirror switch (See page BE±115).
NG Replace remote control mirror switch.
OK
3 Check voltage between remote control mirror switch and battery, remote control
mirror switch and body ground.
PREPARATION:
(a) Disconnect the remote control mirror switch connector.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals R5±6 (B) and R5±2 (E) of the remote control mirror switch.
OK:
Voltage: 10 to 14 V
NG Repair or replace harness or connector.
OK
4 Check wire harness and connector between remote control mirror switch and re-
mote control mirror (See page IN±35).
NG Repair or replace harness or connector.
OK
5 Check retract motor operation (See page BE±115).
NG Replace remote control mirror.
OK

DI±1776
± DIAGNOSTICSBODY CONTROL SYSTEM
1970 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check voltage between terminals GBIG, GB+B and GND of glass breakage sen-
sor ECU.
PREPARATION:
Disconnect the glass breakage sensor ECU connector.
CHECK:
Measure the voltage between terminals GB+B and GND of the glass breakage sensor ECU.
OK:
Voltage: 10 to 14 V
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals GBIG and GND of the glass breakage sensor ECU.
OK:
Voltage: 10 to 14 V
NG Repair or replace wire harness or connector.
OK
2 Check wire harness and connector between glass breakage sensor ECU and
body ECU (See page IN±35).
NG Repair or replace harness or connector.
OK
3 Check wire harness and connector between glass breakage sensor ECU and
glass breakage sensor microphone (See page IN±35).
NG Repair or replace harness or connector.
OK

I28726
G4
I28727
± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1777
1971 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check glass breakage sensor ECU (microphone output).
PREPARATION:
(a) Reconnect the glass breakage sensor ECU, glass break-
age sensor microphone and body ECU connectors.
(b) Connect an oscilloscope to terminal G4±3 of the glass
breakage sensor ECU and body ground.
(c) Turn the ignition switch ON.
CHECK:
Check the signal waveform according to the condition(s) in the
table below.
ItemCondition
Tool setting12 V/DIV, 300 ms/DIV
Vehicle condition
Tap the glass breakage sensor micro-
phone with a hard object such as your
fingernail.
OK:
As shown in the illustration.
NG Replace glass breakage sensor microphone.
HINT:
If the problem recurs even after replacement, replace the glass
breakage sensor ECU.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1686).

DIDEI±01
DI±1778
± DIAGNOSTICSDRIVER DOOR CONTROL SYSTEM
1972 Author: Date:
2005 SEQUOIA (RM1146U)
DRIVER DOOR CONTROL SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77

DI1PB±09
I18633
D22
DRIVER DOOR ECU :
± DIAGNOSTICSDRIVER DOOR CONTROL SYSTEM
DI±1783
1977 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECU
Symbols (Terminal No.)Wiring ColorTerminal DescriptionConditionSpecified Condi-
tion
CPUB e GND
(23 e 13)W±R e W±BBatteryAlways10 to 14 V
BDR e GND
(25 e 13)L±W e W±BBatteryAlways10 to 14 V
CTYB e DCYL
(5 e 6)R e R±WCourtesy switch driver
sideDriver's door closed10 to 14 V
CTYB e DCYL
(5 e 6)R e R±WCourtesy switch driver
sideDriver's door openBelow 1 V
SIG e GND
(21 e 13)B±R e W±BIgnition switchIgnition switch ON10 to 14 V
GND e Body Ground
(13 e Body Ground)W±B e Body
GroundGroundAlwaysBelow 1 V
PLS e SGND
(3 e 4)L±R e W±BPower window pulse
sensorPower window is operatedPulse
Generation
PLS e SGND
(3 e 4)L±R e W±BPower window pulse
sensorPower window is not operated (Switch ON)Below 1 V
PLS e SGND
(3 e 4)L±R e W±BPower window pulse
sensorPower window is not operated (Switch OFF)10 to 14 V
LMT e SGND
(2 e 4)L±Y e W±BPower window limit
switchDriver's door window not fully closed positionBelow 1 V
LMT e SGND
(2 e 4)L±Y e W±BPower window limit
switchDriver's door window fully closed position10 to 14 V
DU e DDN
(1 e 14)R e GPower window motor
(UP)Ignition switch ON and driver's window switch OFFBelow 1 V
DU e DDN
(1 e 14)R e GPower window motor
(UP)Ignition switch ON and driver's window switch UP10 to 14 V
DDN e DU
(14 e 1)G e RPower window motor
(DOWN)Ignition switch ON and driver's window switch OFFBelow 1 V
DDN e DU
(14 e 1)G e RPower window motor
(DOWN)Ignition switch ON and driver's window switch DOWN10 to 14 V
MPX1 e ±
(20 e ±)G±B e ±Multiplex communica-
tion lineMultiplex communication circuit±

± DIAGNOSTICSDRIVER DOOR CONTROL SYSTEM
DI±1789
1983 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check ECU±IG, AM1, PWR No. 1 and ECU±B fuse.
CHECK:
Check continuity of the ECU±IG, AM1, PWR No. 1 and ECU±B fuse.
OK:
Continuity
NG Replace the faulty fuse.
OK
2 Check voltage between terminals BDR, CPUB, SIG and GND of driver door ECU
connector.
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals SIG and GND of the driver door ECU of the wire harness side con-
nector.
OK:
Voltage: 10 to 14 V
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the driver door ECU connector.
CHECK:
Measure the voltage between terminals BDR, CPUB and GND of the driver door ECU of the wire harness
side connector.
OK:
Voltage: 10 to 14 V
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1782).
NG

I18710
D22
Driver Door ECU
D20
Door Key Lock and
Unlock SW Front LH
LSWE
KUL
KL 9
10
22 W±B
LG±R
LG±B 3
6
5 DI±1794
± DIAGNOSTICSDRIVER DOOR CONTROL SYSTEM
1988 Author: Date:
2005 SEQUOIA (RM1146U)
Door key lock and unlock switch circuit
CIRCUIT DESCRIPTION
The door key lock and unlock switch is built in the door lock motor. When the key is turned to the lock side,
terminal 5 of the switch is grounded and when the key is turned to the unlock side, terminal 6 of the switch
is grounded.
The door key lock and unlock switch can be checked using the DTC check (refer to DI±1904).
WIRING DIAGRAM
DI1PH±17