2001 TOYOTA SEQUOIA TS pin

A02961
V5
VVT Sensor (Bank 1)ECM
1
2R
G
Y
LVVL+
VVL±
VVR+
E5 18
19
19
18
VVR±
1
2E5
E4
E4 V6
VVT Sensor (Bank 2)
± DIAGNOSTICSENGINE
DI±87
281 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0016 is displayed, check left bank VVT sensor.

If DTC P0018 is displayed, check right bank VVT sensor.

Read freeze frame data using hand±held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for deter-
mining whether the vehicle was running or stopped, the engine was warmed up or not, the air±fuel ratio
was lean or rich, etc. at the time of the malfunction.
1 Check valve timing (Check for loose and jumping teeth of timing belt) (See page
EM±16).
NG Adjust valve timing (Repair or replace timing
belt).
OK
Replace ECM (See page SF±80).

DI±146
± DIAGNOSTICSENGINE
340 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1
Sensor 2)
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1
Sensor 2)
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1
Sensor 2)
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2
Sensor 2)
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2
Sensor 2)
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2
Sensor 2)
HINT:
Sensor 2 refers to the sensor mounted behind the Three±Way Catalytic Converter (TWC) and located far
from the engine assembly.
CIRCUIT DESCRIPTION
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide
(NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air±fuel
ratio must be precisely controlled so that it is always close to the stoichiometric air±fuel level. For the purpose
of helping the ECM to deliver accurate air±fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since
the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen
concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air±fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor
informs the ECM that the post±TWC air±fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air±fuel ratio is richer than the stoichiometric air±fuel level, the oxygen concentration
in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post±TWC air±fuel ratio is rich
(high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drasti-
cally when the air±fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air±fuel ratio
after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is work-
DIDFR±01

DI±166
± DIAGNOSTICSENGINE
360 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0171
P0174When air±fuel ratio feedback is stable after warming up the
engine, fuel trim is considered to be in error on LEAN side
(2 trip detection logic)

Air induction system

Injector blockage

Mass air flow meter

Engine coolant temperature sensor

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 1, 2 sensor 1)
circuit

Heated oxygen sensor (bank 1, 2 sensor 1)

Heated oxygen sensor heater (bank 1, 2 sensor 1)

EFI relay

PCV piping

ECM
P0172
P0175When air±fuel ratio feedback is stable after warming up the
engine, fuel trim is considered to be in error on RICH side
(2 trip detection logic)

Injector leak, blockage

Mass air flow meter

Engine coolant temperature sensor

Ignition system

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 1, 2 sensor 1)
circuit

Heated oxygen sensor (bank 1, 2 sensor 1)

ECM
HINT:

When DTC P0171 or P0174 is recorded, the actual air±fuel ratio is on the LEAN side. When DTC
P0172 or P0175 is recorded, the actual air±fuel ratio is on the RICH side.

If the vehicle runs out of fuel, the air±fuel ratio is LEAN and DTC P0171 or P0174 may be recorded.
The MIL then comes on.

If the total of the short±term fuel trim value and long±term fuel trim value is within
35 % (engine cool-
ant temperature is more than 75 C (167F)), the system is functioning normally.

DI±170
± DIAGNOSTICSENGINE
364 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

Read freeze frame data using a hand±held tester. Freeze frame data record the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle
was moving or stationary, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, and
other data, from the time the malfunction occurred.

A low A/F sensor voltage could be caused by a rich air±fuel mixture. Check for conditions that would
cause the engine to run rich.

A high A/F sensor voltage could be caused by a lean air±fuel mixture. Check for conditions that would
cause the engine to run lean.
1 Check any other DTCs output (in addition to DTC P0171, P0172, P0174 or P0175).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
Result:
Display (DTC Output)Proceed To
P0171, P0172, P0174 or P0175A
P0171, P0172, P0174 or P0175 and other DTCsB
HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.
B Go to DTC chart (See page DI±58).
A
2 Check connection of PCV piping.
OK:
PCV hose is connected correctly and is not damaged.
NG Repair or replace PCV piping.
OK

A20646
20 V
/Division Injector Signal Waveform
20 V
/Division
GND
100 msec./Division (Idling)(Magnification)
GND
1 msec./Division (Idling)
Injection duration
± DIAGNOSTICSENGINE
DI±185
379 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0300Misfiring of random cylinders is detected

Open or short in engine wire

Connector connection

Vacuum hose connection
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of each cylinder is detected

Vacuum hose connection

Ignition system

Injector

Fuel pressure

Mass air flow meter

Engine coolant temperature sensor

Compression pressure

Valve clearance

Valve timing

PCV piping

ECM
HINT:
When several codes for a misfiring cylinder are recorded repeatedly but no random misfire code is recorded,
it indicates that the misfires have been detected and recorded at different times.
Reference: Inspection using the oscilloscope.
With the engine idling, check the waveform between terminals #1 to #8 and E01 of the ECM connectors.
HINT:
The correct waveform is as shown in the illustration.

DI±192
± DIAGNOSTICSENGINE
386 Author: Date:
2005 SEQUOIA (RM1146U)
1 Are there any other codes (besides DTC P0300, P0301, P0302, P0303, P0304
P0305, P0306, P0307 or P0308) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTCs using hand±held tester.
RESULT:
Display (DTC Output)Proceed to
ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or
P0308ºA
ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or
P0308º and other DTCsB
HINT:
If any other codes besides ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308º are
output, perform the troubleshooting for those DTCs.
B Go to relevant DTC chart (See page DI±58).
A
2 Check wire harness, connector and vacuum hose in engine room.
CHECK:
(a) Check the connection conditions of the wire harness and connector.
(b) Check for the disconnection, piping and brake of the vacuum hose.
NG Repair or replace, then confirm that there is no
misfire (See confirmation driving pattern).
OK

± DIAGNOSTICSENGINE
DI±193
387 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check connection of PCV piping.
OK:
PCV hose is connected correctly and is not damaged.
NG Repair or replace PCV piping.
OK
4 Connect hand±held tester, and read the number of misfire.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) Start the engine.
(d) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / CYL#1 to CYL#8.
CHECK:
Read the number of misfire on the hand±held tester.
HINT:
When a misfire is not reproduced, be sure to branch below based on the stored DTC.
RESULT:
High Misfire Rate CylinderProceed to
1 or 2 cylindersA
More than 3 cylindersB
B Go to step 15.
A

DI±216
± DIAGNOSTICSENGINE
410 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0340 Camshaft Position Sensor ºAº Circuit
(Bank 1 or Single Sensor)
DTC P0341
Camshaft Position Sensor ºAº Circuit Range/Per-
formance (Bank 1 or Single Sensor)
DTC P0345 Camshaft Position Sensor ºAº Circuit
(Bank 2)
DTC P0346 Camshaft Position Sensor ºAº Circuit
Range/Performance (Bank 2)
CIRCUIT DESCRIPTION
The camshaft position sensor consists of a magnet, an iron core and a pick±up coil. This sensor monitors
a timing rotor located on the camshaft and is used by the ECM to detect the camshaft angle. The camshaft
rotation synchronizes with the crankshaft rotation, and this sensor communicates the rotation of the cam-
shaft timing rotor as a pulse signal to the ECM. Based on the signal, the ECM controls fuel injection time
and ignition timing.
If there is no signal from the camshaft position sensor even though the engine is turning or the rotation of
the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction in the sensor
and sets a DTC.
DTC No.DTC Detection ConditionTrouble Area
P0340
No camshaft position sensor signal to ECM during cranking
(2 trip detection logic)
P0340
P0345No camshaft position sensor signal to ECM with engine
speed 600 rpm or more (1 trip detection logic)
Open or short in camshaft position sensor circuit

VVT sensor
P0341
P0346
While crankshaft rotates twice, camshaft position sensor
signal will be input to ECM 12 times or more (1 trip detec-
tion logic)

Hint:
Under normal condition, the camshaft position signal is
input into the ECM 3 times per 2 engine revolutions
VVT sensor

Camshaft

Jumping teeth of timing belt

ECM
DICEZ±02