2001 TOYOTA SEQUOIA TS pin

FI7187
IN0379
Sensor Side
ECU Side
IN0378
Sensor SideECU Side
IN0380
Sensor SideECU Side
IN0381
Pull Lightly
Looseness of Crimping
IN±36± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
36 Author: Date:
2005 SEQUOIA (RM1146U)
2. CONNECTOR HANDLING
When inserting tester probes into a connector, insert them from
the rear of the connector. When necessary, use mini test leads.
For water resistant connectors which cannot be accessed from
behind, take good care not to deform the connector terminals.
3. CONTINUITY CHECK (OPEN CIRCUIT CHECK)
(a) Disconnect the connectors at both ECU and sensor
sides.
(b) Measure the resistance between the applicable terminals
of the connectors.
Resistance: 1 W or less
HINT:
Measure the resistance while lightly shaking the wire harness
vertically and horizontally.
4. RESISTANCE CHECK (SHORT CIRCUIT CHECK)
(a) Disconnect the connectors on both ends.
(b) Measure the resistance between the applicable terminals
of the connectors and body ground. Be sure to carry out
this check on the connectors on both ends.
Resistance: 1 MW or higher
HINT:
Measure the resistance while lightly shaking the wire harness
vertically and horizontally.
5. VISUAL CHECK AND CONTACT PRESSURE CHECK
(a) Disconnect the connectors at both ends.
(b) Check for rust or foreign material, etc. in the terminals of
the connectors.
(c) Check crimped portions for looseness or damage and
check that the terminals are secured in lock portion.
HINT:
The terminals should not come out when pulled lightly from the
back.

IN±42
± INTRODUCTIONTERMS
42 Author: Date:
2005 SEQUOIA (RM1146U) H/B
Hatchback
H±FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HSGHousing
HTHard Top
HWSHeated Windshield System
ICIntegrated Circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, Valve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
ISCIdle Speed Control
J/BJunction Block
J/CJunction Connector
KDKick±Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft±Hand
LHDLeft±Hand Drive
L/H/WLength, Height, Width
LLCLong±Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Differential
LSP & PVLoad Sensing Proportioning And Bypass Valve
LSPVLoad Sensing Proportioning Valve
MAPManifold Absolute Pressure
MAX.Maximum
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MG1Motor Generator No.1
MG2Motor Generator No.2
MPMultipurpose
MPIMultipoint Electronic Injection
MPXMultiplex Communication System
M/T, MTMManual Transmission (Transaxle)
MTMount
MTGMounting
NNeutral
NANatural Aspiration
NO.Number
O2SOxygen Sensor
O/DOverdrive

± INTRODUCTIONTERMS
IN±43
43 Author: Date:
2005 SEQUOIA (RM1146U) OEM
Original Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead Valve
OPTOption
ORVROn±board Refilling Vapor Recovery
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take±Off
P/WPower Window
R & PRack And Pinion
RAMRandom Access Memory
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight±Hand
RHDRight±Hand Drive
RLYRelay
ROMRead Only Memory
RRRear
RRSRigid Front Suspension
RWDRear±Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold±Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
TCTurbocharger
TCCSTOYOTA Computer±Controlled System
TCVTiming Control Valve
TDCTop Dead Center
TEMP.Temperature
TEMSTOYOTA Electronic Modulated Suspension
TFTTOYOTA Free±Tronic
TISTotal Information System For Vehicle Development

MA0055
MA014±06
MA±6
± MAINTENANCEBRAKE
53 Author: Date:
2005 SEQUOIA (RM1146U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND BOOTS
HINT:
Inspect in a well±lighted area. Inspect the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before inspecting the front
brake.
(a) Check all brake lines and hoses for:

Damage

Wear

Deformation

Cracks

Corrosion

Leaks

Bends

Twists
(b) Check all clamps for tightness and connections for leak-
age.
(c) Check that the hoses and lines are clear of sharp edges,
moving parts and the exhaust system.
(d) Check that the lines installed in grommets pass through
the center of the grommets.
2. INSPECT FRONT AND REAR BRAKE PADS AND
DISCS
(Front pads: See page BR±25)
(Rear pads: See page BR±34)
HINT:
If a squealing or scraping noise occurs from the brake during
driving, check the pad wear indicator.
If there are traces of the indicator contacting the disc rotor, the
disc pad should be replaced.

B13807
A: Propeller Shaft Spiders
B: Propeller Shaft Sliding YokesAB
A
A
MA0568
MA±10
± MAINTENANCECHASSIS
57 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Recoat the drive shaft thrust bush with grease (See page
SA±34).
11. 4WD:
LUBRICATE PROPELLER SHAFT AND TIGHTEN
BOLTS
(a) Lubricate the propeller shaft, referring to the lubrication
chart. Before pumping in grease, wipe off any mud and
dust on the grease fitting.
Grease grade:
Propeller shaft (Except Double±cardan joint)
Lithium base chassis grease NLGI No.2
(b) Tighten the bolts for propeller shaft.
(2WD: See page PR±5)
(4WD: See page PR±9)
12. ROTATE TIRE (See page SA±3)
13. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten the following parts:

Seat mounting bolts
Torque:
37 N´m (375 kgf´cm, 27 ft´lbf)

± PREPARATIONENGINE MECHANICAL
PP±5
63 Author: Date:
2005 SEQUOIA (RM1146U)
(09951±07100)Handle 100Spark plug tube
Valve guide bushing
09960±10010Variable Pin Wrench Set
(09962±01000)Variable Pin Wrench Arm AssyCamshaft sub±gear
(09963±00400)Pin 4Camshaft sub±gear
(09963±00500)Pin 5Camshaft sub±gear
(09963±01000)Pin 10Camshaft sub±gear

PP1BM±08
± PREPARATIONENGINE MECHANICAL
PP±7
65 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Caliper gauge
CO/HC meter
Compression gauge
Connecting rod aligner
Cylinder gauge
Dial indicator
Dye penetrant
Engine tune±up tester
Groove cleaning tool
Heater
Magnetic finger
Micrometer
OBD II scan tool
Pin hole grinder
Piston ring compressor
Piston ring expander
Plastigage
Precision straight edge
Press
Ridge reamer
Soft brush
Solvent
Spring testerValve spring
Steel squareValve spring
Thermometer
Torque wrench
Valve seat cutter
Vernier calipers
V±block
Wire brushValve

PP42S±01
PP±36
± PREPARATIONTRANSFER
94 Author: Date:
2005 SEQUOIA (RM1146U)
TRANSFER
SST (Special Service Tools)
09223±15020Oil Seal & Bearing ReplacerPLANETARY GEAR
09223±46011Crankshaft Front Oil Seal
ReplacerTRANSFER ASSEMBLY
09316±60011Transmission & Transfer Bearing
ReplacerREAR OUTPUT SHAFT
DRIVEN SPROCKET
TRANSFER ASSEMBLY
(09316±00011)Replacer PipeREAR OUTPUT SHAFT
TRANSFER ASSEMBLY
(09316±00031)Replacer ºBºDRIVEN SPROCKET
(09316±00071)Replacer ºFºREAR OUTPUT SHAFT
09330±00021Companion Flange Holding ToolTRANSFER ASSEMBLY
09515±30010Rear Wheel Bearing ReplacerPLANETARY GEAR
09554±30011Differential Oil Seal ReplacerPLANETARY GEAR
09555±55010Differential Drive Pinion
Bearing ReplacerPLANETARY GEAR
REAR OUTPUT SHAFT
DRIVEN SPROCKET
09612±65014Steering Worm Bearing PullerPLANETARY GEAR
(09612±01030)Claw ºCºPLANETARY GEAR