2001 TOYOTA SEQUOIA terminal TC

F19749
Junction Connector ºAº Side
(w/ Earth Terminal) Wire Harness View:
J54
W B
Earth Terminal
12345678
9 10111213141516
F19737
DLC3:
D6CANH
CANL
BAT
DI±1108
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
1302 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check CAN bus line for short to +B (DLC3 sub bus line).
PREPARATION:
Disconnect the DLC3 sub bus line connector (J54) from the
junction connector.
NOTICE:

Before disconnecting the connector, make a note of
where it is connected.

Reconnect the connector to its original position.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified value
D6±16 (BAT) ±
D6±6 (CANH)Ignition Switch OFF1 MW or higher
D6±16 (BAT) ±
D6±14 (CANL)Ignition Switch OFF1 MW or higher
NG Repair or replace DLC3 sub bus line or connec-
tor (CAN±H, CAN±L).
OK
2 Connect the connector.
Reconnect the DLC3 sub bus line connector (J54) to the junction connector.
NEXT

F19749
Junction Connector ºAº Side
(w/ Earth Terminal)
Wire Harness View:
J53
W L
Earth Terminal
12345678
9 10111213141516
F19737
DLC3:
D6CANH
CANL
BAT
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
DI±1109
1303 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check CAN bus line for short to +B (ECM main bus line).
PREPARATION:
Disconnect the ECM main bus line connector (J53) from the
junction connector.
NOTICE:

Before disconnecting the connector, make a note of
where it is connected.

Reconnect the connector to its original position.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified value
D6±16 (BAT) ±
D6±6 (CANH)Ignition Switch OFF1 MW or higher
D6±16 (BAT) ±
D6±14 (CANL)Ignition Switch OFF1 MW or higher
OK Go to step 8.
NG
4 Connect the connector.
Reconnect the ECM main bus line connector (J53) to the junction connector.
NEXT

F19749
Junction Connector ºAº Side
(w/ Earth Terminal)
Wire Harness View:
J55
W R
Earth Terminal
12345678
9 10111213141516
F19737
DLC3:
D6CANH
CANL
BAT
DI±1110
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
1304 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check CAN bus line for short to +B (Translate ECU main bus line).
HINT:
For vehicles without an enhanced air suspension system, go to
step 11.
PREPARATION:
Disconnect the translate ECU main bus line connector (J55)
from the junction connector.
NOTICE:

Before disconnecting the connector, make a note of
where it is connected.

Reconnect the connector to its original position.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified value
D6±16 (BAT) ±
D6±6 (CANH)Ignition Switch OFF1 MW or higher
D6±16 (BAT) ±
D6±14 (CANL)Ignition Switch OFF1 MW or higher
OK Go to step 10.
NG
6 Connect the connector.
Reconnect the translate ECU main bus line connector (J55) to the junction connector.
NEXT

F19749
CAN J/C ºAº Side (w/ Earth Terminal)
Wire Harness View:
J56
G
WEarth Terminal
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
DI±1115
1309 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check for an open in one side of the CAN sub bus line (Suspension control ECU
sub bus line).
HINT:
For vehicles without an enhanced air suspension system, go to
step 3.
PREPARATION:
(a) Turn the ignition switch LOCK position.
(b) Disconnect the suspension control ECU sub bus line con-
nector (J56) from the CAN J/C.
NOTICE:

Check the colors of the wire harnesses before dis-
connecting the connector.

Before disconnecting the connector, make a note of
where it is connected.

Reconnect the connector to its original position.
(c) Connect the hand±held tester to the DLC3 via CAN VIM.
(d) Turn the ignition switch ON.
CHECK:
Select ºBUS CHECKº on the hand±held tester display via the
CAN VIM (see page DI±1073).
RESULT:
AºREAR AIRSUSº does not appear
B2 or more ECUs and/or sensors do not appear
A Go to step 4.
B
2 Connect the connector.
(a) Turn the ignition switch LOCK position.
(b) Reconnect the suspension control ECU sub bus line connector (J56) to the CAN J/C.
NEXT

DICY7±02
DI±1118
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1312 Author: Date:
2005 SEQUOIA (RM1146U)
SUPPLEMENTAL RESTRAINT SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77
1. HANDLING PRECAUTIONS FOR AIRBAG SENSOR
HINT:
In this section, the airbag sensor assembly, front airbag sensor LH, front airbag sensor RH, side airbag sen-
sor assembly LH, side airbag sensor assembly RH, curtain shield airbag sensor assembly LH, curtain shield
airbag sensor assembly RH and seat position airbag sensor assembly are collectively referred to as the air-
bag sensor.
(a) Before starting the following operations, wait at least 90 seconds after disconnecting the negative (±)
terminal of the battery:
(1) Replacement of the airbag sensor.
(2) Adjustment of the front/rear doors of the vehicle equipped with the side airbag and curtain shield
airbag (fitting adjustment).
(b) When connecting or disconnecting the airbag sensor connector, ensure that all of the sensors are
installed in the vehicle.
(c) Do not use an airbag sensor which has been dropped during the operation or transportation.
(d) Do not disassemble the airbag sensor.
2. INSPECTION PROCEDURE FOR VEHICLE INVOLVED IN ACCIDENT
(a) When the airbag has not deployed, confirm the DTC by checking the SRS warning light. If there is any
malfunction in the SRS airbag system, perform troubleshooting.
(b) When any of the airbags have deployed, replace the airbag sensor and check the installation condition.
(c) Perform the zero point calibration and sensitivity check under the condition is listed below (see page
DI±1128).

The occupant classification ECU is replaced.

Accessories (seatback tray, seat cover, etc.) are installed.

The passenger seat removed from the vehicle.

The passenger airbag ON/OFF indicator (ºOFFº) comes on when the passenger seat is not occu-
pied.

The vehicle is brought to the workshop for repair due to an accident or a collision.
NOTICE:
When an accident vehicle is brought into the workshop for repair, check the flatness of the body side
that is installed on the passenger seat. If the flatness is not within ± 3.0 mm (0.118 in.), repair it to
the specified range (within ± 3.0 mm (0.118 in.)).

DI6P2±15
DI±1132
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1326 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
Proceed with troubleshooting of each circuit in the table below.
SymptomSuspected AreaSee page

The front passenger seat condition differs from the indication by
the passenger airbag ON/OFF indicator (DTC is not output).
Trouble in indication of Passenger airbag ON/OFF indica-
torDI±1485

With the ignition switch is in ON position, the SRS warning light
sometimes comes on after approximately 6 seconds.
SRS warning light circuit (Always comes on, when DTC is
not output)DI±1491

The SRS warning light always comes on even when DTC is not
output.
SRS warning light circuit (Always comes on, when DTC is
not output)DI±1491

With the ignition switch is in the ON position, the SRS warning
light does not come on.
SRS warning light circuit (Does not come on, when igni-
tion switch is turned to the ON position)DI±1496

Although an SRS warning light operates normally, DTC or a
normal system code is not display.
TC terminal circuitDI±1498

Although terminals TC and CG of DLC3 are not connected, DTC
or a normal system code is display.
TC terminal circuitDI±1498

DIDGL±01
H24009
A19A20A21
17
24 18
23 19
22 20
21 4 8372615
12 13 11 14 10
15 9
16
28 27 26 25 30 294 8372615 4 8372615
10 9 12 13 11 14 15 16 10 9 12 13 11 14 15 16
17 18 19 20 24 23 22 21 17 18 19 20 24 23 22 21
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1133
1327 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECU
1. AIRBAG SENSOR ASSEMBLY
Terminal No.Terminal SymbolDestination
A19±1 (*1)SFL+Side airbag assembly LH (Side squib LH)
A19±2 (*1)SFL±Side airbag assembly LH (Side squib LH)
A19±3 (*1)ICL±Curtain shield airbag assembly LH (Curtain shield airbag LH
squib)
A19±4 (*1)ICL+Curtain shield airbag assembly LH (Curtain shield airbag LH
squib)
A19±5PL+Front seat outer belt LH (P/T squib LH)
A19±6PL±Front seat outer belt LH (P/T squib LH)
A19±9LSP+Seat position airbag sensor assembly
A19±10LBE+Front seat inner belt RH (Seat belt buckle switch LH)
A19±17LSP±Seat position airbag sensor assembly
A19±18LBE±Front seat inner belt RH (Seat belt buckle switch LH)
A19±19 (*1)VUPLSide airbag sensor assembly LH
A19±20 (*1)VUCLCurtain shield airbag sensor assembly LH
A19±21 (*1)ESLSide airbag sensor assembly LH
A19±22 (*1)ESCLCurtain shield airbag sensor assembly LH
A20±1P2+Front passenger airbag assembly (P squib (Dual stage ± 2nd
step))
A20±2P2±Front passenger airbag assembly (P squib (Dual stage ± 2nd
step))
A20±3P±Front passenger airbag assembly (P squib)
A20±4P+Front passenger airbag assembly (P squib)
A20±5D+Steering wheel pad (D squib)
A20±6D±Steering wheel pad (D squib)
A20±7D2±Steering wheel pad (D squib (Dual stage ± 2nd step))
A20±8D2+Steering wheel pad (D squib (Dual stage ± 2nd step))
A20±13PBEWIntegration control and panel (Seat belt warning light)
A20±14LACombination meter (SRS warning light)
A20±15TCDLC3

H22556
O6
O7
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1135
1329 Author: Date:
2005 SEQUOIA (RM1146U)
2. OCCUPANT CLASSIFICATION ECU
Terminal No. (Symbols)Wiring ColorTerminal DescriptionConditionSpecification
O6±1 (+B) ±
O6±3 (GND)W±R ± W±BBatteryIgnition switch ON10 to 14 V
O6±2 (DIA) ±
O6±3 (GND)G±R ± W±BDiagnosis (DLC3)Ignition switch ONPulse generation
O6±3 (GND) ±
Body groundW±B ± Body groundGroundAlwaysBelow 1 V
O6±4 (FSR±) ±
O6±3 (GND)B ± W±BAirbag sensor assy center
communication line (±)AlwaysBelow 1 V
O6±5 (BGND) ±
O6±3 (GND)L ± W±BPassenger side buckle
switch ground lineAlwaysBelow 1 V
O6±7 (IG) ± O6±3 (GND)B±O ± W±BPower source (IGN1 Fuse)Ignition switch ON10 to 14 V
O6±8 (FSR+) ±
O6±4 (FSR±)W ± BAirbag sensor assy center
communication lineIgnition switch ONPulse generation
O6±9 (BSW) ±
O6±5 (BGND)R ± LPassenger side buckle
switch lineAlwaysPulse generation
O7±1 (SGD1) ±
O6±3 (GND)O ± W±BOccupant classification
sensor front LH ground lineAlwaysBelow 1 V
O7±2 (SGD2) ±
O6±3 (GND)B±Y ± W±B
Occupant classification
sensor front RH ground
line
AlwaysBelow 1 V
O7±3 (SGD3) ±
O6±3 (GND)R±B ± W±BOccupant classification
sensor rear LH ground lineAlwaysBelow 1 V
O7±4 (SGD4) ±
O6±3 (GND)R±W ± W±BOccupant classification
sensor rear RH ground lineAlwaysBelow 1 V
O7±5 (SVC3) ±
O7±3 (SGD3)Y±B ± R±B
Occupant classification
sensor rear LH power sup-
ply lineIgnition switch ON, a load
is applied to occupant clas-
sification sensor rear LH
4.5 to 5.1 V
O7±6 (SVC4) ±
O7±4 (SGD4)Y ± R±W
Occupant classification
sensor rear RH power sup-
ply lineIgnition switch ON, a load
is applied to occupant clas-
sification sensor rear RH
4.5 to 5.1 V
O7±7 (SIG1) ±
O7±1 (SGD1)G ± OOccupant classification
sensor front LH signal lineIgnition switch ON, a load
is applied to occupant clas-
sification sensor front LH
0.2 to 4.9 V
O7±8 (SIG2) ±
O7±2 (SGD2)LG ± B±YOccupant classification
sensor front RH signal lineIgnition switch ON, a load
is applied to occupant clas-
sification sensor front RH
0.2 to 4.9 V
O7±9 (SIG3) ±
O7±3 (SGD3)G±B ± R±BOccupant classification
sensor rear LH signal lineIgnition switch ON, a load
is applied to occupant clas-
sification sensor rear LH
0.2 to 4.9 V
O7±10 (SIG4) ±
O7±4 (SGD4)L±W ± R±WOccupant classification
sensor rear RH signal lineIgnition switch ON, a load
is applied to occupant clas-
sification sensor rear RH
0.2 to 4.9 V