2001 TOYOTA SEQUOIA engine

A19690
C1
Camshaft Position Sensor
C2
Crankshaft Position SensorLECM
NE+
NE±
E2 27
2 12 1
25
24 Y
R GE6
G2+
G2±
32
E6
E6
E6
*1: ShieldedE6E1
EC (*1) (*1)
J42 J/C
A
AA
BR
BR
BR1 DI±212
± DIAGNOSTICSENGINE
406 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

A21026
Component Side
C2
Crankshaft Position Sensor
± DIAGNOSTICSENGINE
DI±213
407 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:

Read freeze frame data using the hand±held tester. Freeze frame records the engine conditions when
a malfunction is detected. When troubleshooting it is useful for determining whether the vehicle was
running or stopped. the engine was warmed up or not, the air±fuel ratio lean or rich, etc. at the time
of the malfunction.

READ VALUE ON HAND±HELD TESTER
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and push the hand±held tester tool main switch ON.
(c) When using hand±held tester, enter the following menu: ºDIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / ENGINE SPDº.

The engine speed can be confirmed in DATA LIST using the hand±held tester. If there are no NE sig-
nals from the crankshaft position sensor despite the engine revolving, the engine speed will be indi-
cated as zero. If voltage output of the crankshaft position sensor is insufficient, the engine speed will
be indicated as lower RPM (than the actual RPM).
1 Check resistance of crankshaft position sensor.
PREPARATION:
Disconnect the C2 crankshaft position sensor connector.
CHECK:
Measure the resistance between terminals 1 and 2.
OK:
Standard:
Tester ConnectionSpecified Condition
1 ± 2985 to 1,600 W at cold
1 ± 21,265 to 1,890 W at hot
NOTICE:
º Coldº and ºHotº shown above mean the temperature of
the coils themselves. ºColdº is form ±10°C (14°F) to 50°C
(122°F) and ºHotº is from 50°C (122°F) to 100°C (212°F).
NG Replace crankshaft position sensor.
OK

A21027
Wire Harness Side
Crankshaft Position Sensor C2
B17414
E6ECM Connector
NE± NE+
BR3795OK NGClearance
DI±214
± DIAGNOSTICSENGINE
408 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector between ECM and
crankshaft position sensor.
PREPARATION:
(a) Disconnect the C2 crankshaft position sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
Crankshaft position sensor (C2±1) ±
NE+ (E6±21)Below 1 W
Crankshaft position sensor (C2±2) ±
NE± (E6±20)Below 1 W
Crankshaft position sensor (C2±1) or
NE+ (E6±21) ± Body ground10 kW or higher
Crankshaft position sensor (C2±2) or
NE± (E6±20) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
3 Check sensor installation (crankshaft position sensor).
CHECK:
Check the crankshaft position sensor installation.
OK:
The crankshaft position sensor is installed properly.
NG Tighten sensor installation bolt.
OK

± DIAGNOSTICSENGINE
DI±215
409 Author: Date:
2005 SEQUOIA (RM1146U)
4 Inspect teeth of sensor plate.
PREPARATION:
Remove the crankshaft angle sensor plate (See page EM±99).
CHECK:
Check the teeth of sensor plate.
NG Replace sensor plate.
OK
Replace ECM (See page SF±80).

DI±216
± DIAGNOSTICSENGINE
410 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0340 Camshaft Position Sensor ºAº Circuit
(Bank 1 or Single Sensor)
DTC P0341
Camshaft Position Sensor ºAº Circuit Range/Per-
formance (Bank 1 or Single Sensor)
DTC P0345 Camshaft Position Sensor ºAº Circuit
(Bank 2)
DTC P0346 Camshaft Position Sensor ºAº Circuit
Range/Performance (Bank 2)
CIRCUIT DESCRIPTION
The camshaft position sensor consists of a magnet, an iron core and a pick±up coil. This sensor monitors
a timing rotor located on the camshaft and is used by the ECM to detect the camshaft angle. The camshaft
rotation synchronizes with the crankshaft rotation, and this sensor communicates the rotation of the cam-
shaft timing rotor as a pulse signal to the ECM. Based on the signal, the ECM controls fuel injection time
and ignition timing.
If there is no signal from the camshaft position sensor even though the engine is turning or the rotation of
the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction in the sensor
and sets a DTC.
DTC No.DTC Detection ConditionTrouble Area
P0340
No camshaft position sensor signal to ECM during cranking
(2 trip detection logic)
P0340
P0345No camshaft position sensor signal to ECM with engine
speed 600 rpm or more (1 trip detection logic)
Open or short in camshaft position sensor circuit

VVT sensor
P0341
P0346
While crankshaft rotates twice, camshaft position sensor
signal will be input to ECM 12 times or more (1 trip detec-
tion logic)

Hint:
Under normal condition, the camshaft position signal is
input into the ECM 3 times per 2 engine revolutions
VVT sensor

Camshaft

Jumping teeth of timing belt

ECM
DICEZ±02

A23538
20 msec./DIV (idling) 2 V/DIV
Ground VV1
VV2
NE VV1, VV2 and NE Signal Waveforms
Ground
Ground
± DIAGNOSTICSENGINE
DI±217
411 Author: Date:
2005 SEQUOIA (RM1146U)
Reference: Inspection using the oscilloscope.
The correct waveform is as shown.
Tester ConnectionSpecified Condition
G2+ (E5±27) ± G2± (E5±32)Ct fi hNE+ (E5±25) ± NE± (E5±24)Correct waveform is as shown
MONITOR DESCRIPTION
If there are no signals from the camshaft position sensor even though the engine is turning, or if the rotation
of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sen-
sor.
MONITOR STRATEGY
P0340VVT sensor (Bank 1) range check or rationality
RltdDTCP0341VVT sensor (Bank 1) range check or rationalityRelated DTCsP0345VVT sensor (Bank 2) range check or rationality
P0346VVT sensor (Bank 2) range check or rationality
Rid / tMain sensors/componentsVVT sensorRequired sensors/componentsRelated sensors/componentsCrankshaft position sensor, Engine speed sensor
Frequency of operationContinuous
Duration5 sec.
MIL operationP0340, P0345 case 1: 2 driving cycles
P0340, P0345 case 2, P0341, P0346: Immediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
P0340, P0345 Case 1:
StarterON
Minimum battery voltage while starter ON±11 V
P0340, P0345 Case 2:
Engine RPM600 rpm±
StarterOFF
Battery voltage8 V±
Ignition switchON
P0341, P0346:
StarterAfter OFF to ON timing
Engine revolution720CA

DI±218
± DIAGNOSTICSENGINE
412 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
P0340, P0345 Case 1:
VVT sensor signalNo signal
P0340, P0345 Case 2:
VVT sensor signalNo signal
P0341, P0346:
VVT sensor count12 or more / 720CA (= Engine 2 revolutions)
COMPONENT OPERATING RANGE
ParameterStandard Value
VVT sensor signal input during every 720CA3
WIRING DIAGRAM
Refer to DTC P0335 on page DI±210.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check resistance of camshaft position sensor (See page SF±76).
NG Repair or replace harness or connector.
OK

B17414
E6
ECM Connector
VV2+
VV1±
VV1+VV2±
A21029
Wire Harness Side
VVT Sensor V16
V17
BR3795OK NGClearance
± DIAGNOSTICSENGINE
DI±219
413 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector between ECM and VVT sen-
sor.
PREPARATION:
(a) Disconnect the VVT sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
VVT sensor (V16±1) ± VV1+ (E6±25)Below 1 W
VVT sensor (V16±2) ± VV1± (E6±24)Below 1 W
VVT sensor (V17±1) ± VV2+ (E6±18)Below 1 W
VVT sensor (V17±2) ± VV2± (E6±28)Below 1 W
VVT sensor (V16 ±1) or
VV1+ (E6±25) ± Body ground10 kW or higher
VVT sensor (V16±2) or
VV1± (E6±24) ± Body ground10 kW or higher
VVT sensor (V17 ±1) or
VV2+ (E6±18) ± Body ground10 kW or higher
VVT sensor (V17±2) or
VV2± (E6±28) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
3 Check sensor installation (VVT position sensor).
CHECK:
Check the VVT position sensor installation.
OK:
The VVT sensor is installed properly.
NG Tighten sensor installation bolt.
OK