2001 TOYOTA SEQUOIA ESP

DID9S±01
I24383
º1chº Switch
ºSEEK TRACKº
DOWN SwitchºSEEK TRACKº
UP SwitchºDISCº Switch º2chº Switchº3chº Switch
º4chº Switchº5chº Switch
º6chº Switch
DI±1974
± DIAGNOSTICSAUDIO SYSTEM
2168 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
1. DIAGNOSTIC CHECK
(a) Starting Diagnostic Mode (All elements come on during the SW check mode).
(1) Turn off the audio system and turn the ignition switch to the ACC position. While pressing the
preset switches º1º and º6º at the same time, press the ºDISCº 3 times.
(2) Reference:
When the system enters the Diagnosis Mode, a beep sound is emitted 3 times and all the
elements come on during the SW check mode.
It takes about 40 seconds to complete the check.
Turn all the elements in the LCD on.
When pressing the switch, confirm beep sound is emitted.
(b) Service Check Screen.
(1) Press the ºSEEK TRACKº switch to enter the ºService Check Screenº.
(2) In the service check mode, the system check and the diagnostic memory check are performed,
and the check results are displayed in ascending order of the component codes (physical ad-
dress.)
TermsMeaning
Component code
(Physical address)Three±digit code (In hexadecimal) given to each device comprising AVC±LAN.
Corresponding to its function, individual symbol is provided.
Logical addressTwo±digit code (In hexadecimal) given to each function and device unit in each
device comprising AVC±LAN.
Code No. (physical address) List
Code No.
(physical address)Equipment name
190Radio receiver assy (Audio head unit)
440Stereo component amplifier assy
1F6Multi±display controller (RSE ECU)
1F4Rear seat audio controller
(c) Finishing Diagnostic Mode.
Press the ºDISCº for 2 seconds or more, or turn the ignition switch off.

DI±1976
± DIAGNOSTICSAUDIO SYSTEM
2170 Author: Date:
2005 SEQUOIA (RM1146U)
(2) Check Result Display.
DisplayOriginal LanguageMeaningAction to be taken
goodGood (normal)No DTCs are detected in both ºSystem Check Modeº and
ºDiagnostic Memory Modeº.±
NCONNo connection
The system recognized the component when it was regis-
tered, but the component gives no response to the ºDiagnos-
tic Mode ON Requestº.
Check the power source cir-
cuit and the communication
circuit of the component indi-
cated by the component
code (physical address).
ECHNExchangeOne or more DTCs for ºExchangeº are detected in either
ºSystem Check Modeº or ºDiagnostic Memory Modeº.
Go to the detailed informa-
tion mode to check the
trouble area referring to the
DTC list.
CHECCheck
When no DTCs are detected for ºExchangeº, one or more
DTCs for ºCheckº are detected in either ºSystem Check
Modeº or ºDiagnostic Memory Modeº.Go to the detailed informa-
tion mode to check the
trouble area referring to the
DTC list.
OLDOld versionOld DTC application is identified and DTC is detected in ei-
ther ºSystem Check Modeº or ºDiagnostic Memory Modeº.±
NRESNo response
The device gives no response to any one of ºSystem Check
Mode ON Requestº, ºSystem Check Result Requestº and
ºDiagnostic Memory Requestº.
Check the power source cir-
cuit and the communication
circuit of the component indi-
cated by the component
code (physical address).
(3) To perform the Service Check again, press the preset switch º1º.
(e) Detailed Information Mode (when displaying the DTC for a trouble component)
(1) With ºCHECº or ºECHNº being displayed, press the preset switch º2º to go to the detailed informa-
tion mode.
(2) Press the ºSEEK TRACKº switch to display the ºSystem Check Result (SYS)º and ºDiagnostic
Memory Response (CODE)º.

I28310
Service Check Mode
Detailed Information ModeDISC/CH/PROG DOWN
Detailed information
of the first code
is displayed
Detailed information
of the second code
is displayed
Continue to display detailed information
when more than one DTC is detected.
The illustration shows the case that the component with code 190 has DTC º47º and ºdCº as a result of the
system check and the diagnosis memory response.
The detailed information mode shows the system check result first, then the diagnosis memory response result.
(*1): As for DTC that does not have any sub code, sub code is not displayed.P±±±indicates physical address
190±±±physical address
SYS±±±system check result
P±±±indicates physical address
360±±±sub code
6F±±±connection
check number 1±±±the first code
62±±±logical address
DC±±±DTC CODE±±±diagnosis memory
response result
2±±±the second code
01±±±logical address
05±±±the number of times of
occurrence
(in decimal) 47±±±DTC
Continue to display detailed information
when more than one DTC is detected.*

From *

To *
(*1)
: TUNE/TRACK UP
: TUNE/TRACK DOWN
DISC/CH/PROG UP
± DIAGNOSTICSAUDIO SYSTEM
DI±1977
2171 Author: Date:
2005 SEQUOIA (RM1146U)

DID9T±01
± DIAGNOSTICSAUDIO SYSTEM
DI±1979
2173 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
TermsMeaning
Physical addressThree±digit code (shown in hexadecimal) which is given to each component com-
prising the AVC±LAN.
Corresponding to the function, individual symbols are specified.
Logical addressTwo±digit code (shown in hexadecimal) which is given to each function comprising
the inner system of the AVC±LAN.
HINT:
Titles for each unit are stated in the following order: parts name (physical address) and [Name indicated on
the DTC display]
1. Radio receiver assy (physical address: 190) [AUDIO H/U]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
D6
*1Absence of Master
Component in which this code is recorded was
disconnected from system or master component
with ignition switch in ACC or ON.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
D8
*2
*5No Response to Connection
CheckComponent shown by sub code is or was discon-
nected from system after engine start.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±

DI±1980
± DIAGNOSTICSAUDIO SYSTEM
2174 Author: Date:
2005 SEQUOIA (RM1146U)D9
*1
Last Mode Error
Audio or visual component operated before en-
gine stop is or was disconnected with ignition
switch in ACC or ON.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
DA
*5No Response to ON/OFF
Instruction
No response is identified when changing mode
(audio and visual mode change).
Sound and picture does not change by button op-
eration.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±

DI±1986
± DIAGNOSTICSAUDIO SYSTEM
2180 Author: Date:
2005 SEQUOIA (RM1146U)
3. Multi±display controller sub±assy (Physical address: 1F6) [RSE ECU, MAIN]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
21ROM ErrorAbnormal condition of ROM is detected.Replace multi±display controller
sub±assy.±
22ROM ErrorAbnormal condition of RAM is detected.Replace multi±display controller
sub±assy.±
D1
*1
Registered component discon-
nected
AVC±LAN transmitting abnor-
malitiesComponent shown by sub±code is or was discon-
nected from system with ignition switch in ACC or
ON.
Communication with component shown by sub±
code is not ensured when engine is started.
1. Power source circuit (Multi±dis-
play controller sub±assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±2110
DI±2139
±
D7
*2No response to connection
checkComponent shown by sub±code is or was discon-
nected from system after engine started.
1. Power source circuit (Multi±dis-
play controller sub±assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±2110
DI±2139
±
D7
*2AVC±LAN Communication
Check Error
Component in which this code is recorded is or
was disconnected from system after engine start.
Or, when recording this code, multi±display con-
troller was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
4. Replace Multi±display controller
sub±assy.DI±1990
DI±2110
DI±2139
±
D6
*1Absence of Master
Component in which this code is recorded has
been disconnected from system with ignition in
ACC or ON. Or, when this code was recorded,
multi±display controller was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±
D7
*2Connection Check Error
Component in which this code is recorded has
been disconnected from system after engine start.
Or, when this code was recorded, multi±display
controller was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±
DC
*3Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DD
*4Master Reset (Momentary Inter-
ruption)Component that is to be master has been discon-
nected after engine start.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±

DI±1988
± DIAGNOSTICSAUDIO SYSTEM
2182 Author: Date:
2005 SEQUOIA (RM1146U)E0
*1
Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
E3
*1Registration Request Transmis-
sion

Registration Request command is output from
slave component.

Registration Request command is output from
sub±master component.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
±
D8
*2No Response To Connection
CheckComponent shown by sub±code is or had been
disconnected from system after engine start.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
D9
*1Last Mode Error
Component operated (sound and/or image was
provided) before engine stop is or was discon-
nected with ignition switch in ACC or ON.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DANo Response to ON/OFF
Instruction
No response is identified when changing mode
(audio and visual mode change).
Detected when sound and picture does not
change by button operation
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DB
*1Mode Status ErrorDual alarm is detected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DC
*4Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DE
*3Slave Reset (Momentary Inter-
ruption)After engine start, slave component has been dis-
connected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting the engine.

DIDAH±01
I28317
Switch Assy:
± DIAGNOSTICSREAR SEAT AUDIO SYSTEM
DI±2053
2247 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
1. DIAGNOSIS CHECK
HINT:
RSA system inspects the devices consisting of Sub AVC±LAN
on the rear seat audio controller assy.
(a) Starting Main AVC±LAN (See page DI±1974, DI±2191).
HINT:
As starting Main AVC±LAN to operate the diagnosis
mode, Sub AVC±LAN also automatically enters the diag-
nosis mode. Perform the diagnosis mode operation on
the rear seat audio controller assy.
Use a switch assy to operate diagnosis mode.
(b) Service Check Screen
Reference
In the service check mode, the system check and
the diagnosis memory check are performed, and
the check results are displayed in ascending order
of the device codes (physical address).
TermsMeaning
Component code
(Physical address)Three±digit code (In hexadecimal) given to each device
comprising AVC±LAN. Corresponding to its function, individ-
ual symbol is provided.
Logical addressTwo±digit code (In hexadecimal) given to each function and
device unit in each device comprising AVC±LAN.
(c) Finishing Diagnosis Mode (See page DI±1974,
DI±2191).
(d) Element Check Mode
After the diagnosis start±up, the system enters the ele-
ment check mode. Check that the all elements come on.