Page 1030 of 4323

DI±828
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1022 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure monitor valve sub±assy and/or
the tire pressure monitor ECU (see page DI±805).
HINT:
Set the tire pressure to the specified value.
1 Forcibly transmit transmitter ID of all wheels.
PREPARATION:
Remove the valve cores of the all wheels to rapidly reduce the pressure of all tires to 120 kPa (1.2 kgf/cm2,
17 psi respectively).
HINT:
The transmitter ID can be transmitted forcibly by rapidly reducing tire air pressure.
NEXT
2 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
OK Set tire pressure to normal value (Transmitter
stop condition is completely reset).
NG
3 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure back to the specified normal value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
Page 1031 of 4323
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±829
1023 Author: Date:
2005 SEQUOIA (RM1146U)
4 Forcibly transmit transmitter ID.
PREPARATION:
(a) Forcibly transmit the transmitter ID by performing the following:
(1) Set the tire pressure to the specified value.
(2) Rotate the tire 90 to 270 degrees.
(3) Rapidly reduce the pressure of all tires to 120 kPa (1.2 kgf/cm
2, 17 psi respectively).
(4) Perform the steps mentioned above to all tires including the spare tire.
NEXT
5 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
HINT:
A system error is probable if NG. If any DTC other than C2111/21, C2112/22, C2113/23, C2114/24 and
C2115/25, is output, perform troubleshooting according to that DTC.
OK Set tire pressure to normal value (Transmitter
stop condition is completely reset).
NG
6 Check DTC (See page DI±820).
CHECK:
Check if DTCs C2111/21, C2112/22, C2113/23, C2114/24 and C2115/25 are all output.
No Go to step 12.
Ye s
Page 1034 of 4323

F19140
Example:
Front
A
B
DI±832
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1026 Author: Date:
2005 SEQUOIA (RM1146U)
12 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
13 Identify transmitter corresponding to DTC (See page DI±881).
NEXT
14 Interchange tires.
PREPARATION:
Interchange tire ºAº with a defective tire pressure monitor valve
sub±assy with tire ºBº with a normal one.
HINT:
If tire ºAº (left front) is identified in step 13.
NEXT
15 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
Page 1041 of 4323
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±839
1033 Author: Date:
2005 SEQUOIA (RM1146U)
9 Replace tire pressure monitor ECU and check DTC.
PREPARATION:
(a) Replace the tire pressure monitor ECU (see page SA±20).
(b) Clear the DTCs.
CHECK:
Check for a DTC.
OK:
DTC is not output.
NG Replace tire pressure monitor valve sub±assy
(See page SA±16).
OK
End
10 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
11 Identify transmitter corresponding to DTC (See page DI±881).
NEXT
Page 1045 of 4323
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±843
1037 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure monitor valve sub±assy and/or
the tire pressure monitor ECU (see page DI±805).
HINT:
Set the tire pressure to the specified value.
1 Check tire pressure warning lamp.
PREPARATION:
Turn the ignition switch to the ON position.
CHECK:
Check the tire pressure warning lamp.
RESULT:
Does not blinkA
Comes on and goes off repeatedly at 0.5 second intervalsB
B Go to step 5.
A
2 Identify transmitter corresponding to DTC (See page DI±881).
NEXT
3 Clear DTC (See page DI±820).
NEXT
Page 1046 of 4323
DI±844
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1038 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
HINT:
If the result is OK, replace the tire pressure monitor valve sub±assy specified in STEP 2.
Before installing a new tire pressure monitor valve sub±assy, read and write down its transmitter ID.
Register the transmitter ID after replacement and then set the tire pressure to the specified value (see
page DI±805).
NG Go to step 9.
OK
Replace tire pressure monitor valve sub±
assy (See page SA±16).
HINT:
Replace the identified tire pressure monitor valve sub±assy.
5 Identify transmitter corresponding to recorded DTC (See page DI±881).
NEXT
6 Replace tire pressure monitor valve sub±assy (See page SA±16).
PREPARATION:
Replace the identified tire pressure monitor valve sub±assy with a new one.
HINT:
Before installing a new tire pressure monitor valve sub±assy, read and write down its transmitter ID.
NEXT
Page 1050 of 4323

DI±848
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1042 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure monitor valve sub±assy and/or
the tire pressure monitor ECU (see page DI±805).
HINT:
Set the tire pressure to the specified value.
1 Check tire pressure warning lamp.
PREPARATION:
Turn the ignition switch to the ON position.
CHECK:
Check the tire pressure warning lamp.
RESULT:
Does not blinkA
Comes on and goes off repeatedly at 0.5 second intervalsB
B Go to step 6.
A
2 Identify transmitter corresponding to DTC (See page DI±881).
NEXT
3 Adjust tire pressure to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
4 Clear DTC (See page DI±820).
NEXT
Page 1051 of 4323

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±849
1043 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
HINT:
If the result is OK, replace the tire pressure monitor valve sub±assy specified in STEP 2.
Register the transmitter ID after replacement and then set the tire pressure to the specified value.
NG Go to step 11.
OK
Replace tire pressure monitor valve sub±
assy (See page SA±13).
6 Identify transmitter corresponding to DTC (See page DI±881).
NEXT
7 Adjust tire pressure to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
8 Replace tire pressure monitor valve sub±assy (See page SA±16).
PREPARATION:
Replace the identified tire pressure monitor valve sub±assy with a new one.
HINT:
Before installing a new tire pressure monitor valve sub±assy onto the wheel, read and write down its trans-
mitter ID.
NEXT