Page 306 of 1897

BE04Q-06
BE-2
- BODY ELECTRICALTROUBLESHOOTING
1606 Author: Date:
2001 AVALON (RM808U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
POWER OUTLET
SymptomSuspect AreaSee page
Electric power source cannot be taken out of the power outlet11. PWR OUTLET No. 1, 2 Fuse
12.Wire Harness-
-
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
HEADLIGHT AND TAILLIGHT SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
FOG LIGHT SYSTEM:
SymptomSuspect AreaSee page
Fog light does not light with light control SW HEAD.
(Headlight is normal)
1. FOG Fuse
2. Fog Light Relay
3. Fog Light Switch
4. Wire Harness-
BE-26
BE-26
-
Fog light does not light with light control SW HEAD.
(Headlight does not light)1. Other Parts*1
2. Wire Harness
-
-
Only one light does not light.1. Bulb
2. Wire Harness-
-
*1: Inspect Headlight System.
TURN SIGNAL AND HAZARD WARNING SYSTEM:
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE-29
BE-29
-
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Switch
3. Wire Harness-
BE-29
-
Hazard warning light does not light up.
(Turn is normal.)1. HAZ Fuse
2. Wire Harness-
-
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE-29
-
*1Turn signal does not light up.
1. Ignition Switch
2. TURN Fuse
3. Turn Signal Switch
4. Wire HarnessBE-16
-
BE-29
-
*2Turn signal does not light up.
1. TURN Fuse
2. Turn Signal Switch
3. Wire Harness-
BE-29
-
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE-29
-
Only one bulb does not light up.1. Bulb
2. Wire Harness-
-
*1: Combination Meter, Wiper and Washer do not operate.
*
2: Combination Meter, Wiper and Washer are normal.
Page 310 of 1897

BE-6
- BODY ELECTRICALTROUBLESHOOTING
1610 Author: Date:
2001 AVALON (RM808U) Shift indicator lights do not light up.
1. Bulb
2. Park/Neutral Position Switch
3. Meter Circuit Plate
4. Wire Harness-
DI-199
BE-43
-
Only one shift indicator does not light up.1. Bulb
2. Meter Circuit Plate-
BE-43
Malfunction indicator light does not light up.
1. Bulb
2. ECM
3. Meter Circuit Plate
4. Wire Harness-
DI-1
BE-43
-
SLIP indicator light does not light up.
1. Bulb
2. ABS & TRAC ECU
3. Meter Circuit Plate
4. Wire Harness-
DI-250
BE-43
-
TRAC OFF indicator light does not light up.
1. Bulb
2. ABS & TRAC ECU
3. Meter Circuit Plate
4. Wire Harness-
DI-250
BE-43
-
Security indicator light does not light up.
1. LED
2. Theft Deterrent ECU
3. Meter Circuit Plate
4. Wire Harness-
DI-517
BE-43
-
Indicator lights do not light up. (Except Turn, Hi-beam and
security)1. GAUGE Fuse
2. Wire Harness-
-
DEFOGGER SYSTEM:
SymptomSuspect AreaSee page
All defogger systems do not operate.
1. SEAT HEATER Fuse
2. DEF Fuse
3. Defogger Relay
4. Defogger Switch
5. Wire Harness-
-
BE-67
DI-1
-
Rear window defogger does not operate.
1. Defogger Wire
2. Choke Coil
3. Wire HarnessBE-67
-
-
Mirror defogger does not operate.
1. MIR/HTR Fuse
2. Mirror Defogger
3. Wire Harness-
BE-67
-
POWER WINDOW CONTROL SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
POWER DOOR LOCK CONTROL SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
Page 311 of 1897

- BODY ELECTRICALTROUBLESHOOTING
BE-7
1611 Author: Date:
2001 AVALON (RM808U)
WIRELESS DOOR LOCK CONTROL SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
Some functions of wireless door lock control system do not operate.
HINT:
Troubleshooting of the wireless door lock control system is based on the premise that the door lock
control system is operating normally. Accordingly, before troubleshooting the wireless door lock control
system, first make certain that the door lock control system is operating normally.
If the trouble still reappears even though there are no abnormalities in any of the other circuits, then
check and replace the Wireless Door Lock Control Receiver as the last step.
SLIDING ROOF SYSTEM:
SymptomSuspect AreaSee page
Sliding roof system does not operate.
(Door Lock does not operate)1. SUN ROOF Fuse
2. GAUGE Fuse
3. Wire Harness-
-
-
Sliding roof system does not operate.
(Door Lock is normal)
1. Sliding Roof Control Switch
2. Sliding Roof Motor and Limit Switch
3. Sliding Roof Control Relay
4. Wire HarnessBE-103
BE-103
BE-103
-
Sliding roof system operates abnormally.
1. Sliding Roof Control Switch
2. Sliding Roof Motor and Limit Switch
3. Sliding Roof Control Relay
4. Wire HarnessBE-103
BE-103
BE-103
-
Sliding roof system stops operation half way.
(Stones of foreign material trapped in motor assembly)1. Sliding Roof Control Relay and Switch
2. Sliding Roof Motor and Limit Switch
3. Wire HarnessBE-103
BE-103
-
ºKey-of f Sliding Roofº operation does not operate.
1. DOOR Fuse
2. GAUGE Fuse
3. Ignition Switch
4. Body ECU
5. Wire Harness-
-
BE-16
BE-16
-
POWER SEAT CONTROL SYSTEM (w/o Driving position memory driver's seat):
SymptomSuspect AreaSee page
Power seat does not operate.
(Door lock system does not operate)1. DOOR Fuse
2. Wire Harness-
-
Power seat does not operate.
(Door lock system is normal)1. Power Seat Swtich (D,P)
2. Wire HarnessBE-105
-
ºSlide operationº does not operate.
1. Power Seat Switch (D, P)
2. Slide Motor (D, P)
3. Wire HarnessBE-16
BE-105
-
ºFront vertical Operationº does not operate.
1. Power Seat Switch (D, P)
2. Front Vertical Motor (D, P)
3. Wire HarnessBE-105
BE-105
-
ºRear verticalº does not operate.
1. Power Seat Switch
2. Rear Vertical Motor
3. Wire HarnessBE-105
BE-105
-
ºReclining Operationº does not operate.
1. Power Seat Switch (D, P)
2. Reclining Motor (D, P)
3. Wire HarnessBE-105
BE-105
-
(D): Driver's Seat
(P): Passenger's Seat
Page 314 of 1897
BE0I0-04
I12526
Turn Signal Light
Combination Switch
Turn Signal Switch
Turn Signal Light
Hazard Warning Switch
Flasher Relay
Engine Room Junction Block
HAZ Fuse
Driver Side Junction Block
TURN Fuse
BE-28
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
1632 Author: Date:
2001 AVALON (RM808U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION
Page 318 of 1897
BE0IA-03
I12530
Wiper Motor
Washer Tank
Washer Motor
Combination Switch
Wiper and Washer Switch
Ignition Switch Driver Side Junction Block
WIP Fuse
IG1 Relay
- BODY ELECTRICALWIPER AND WASHER SYSTEM
BE-37
1641 Author: Date:
2001 AVALON (RM808U)
WIPER AND WASHER SYSTEM
LOCATION
Page 319 of 1897
BE2MA-01
I20790
Key Plate Inserted
ON
OFFWithin. 5 sec.
1 Key Plate Not Inserted
23 910Within. 30 sec.
Once Nine times
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-91
1695 Author: Date:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT WIRELESS DOOR LOCK DIAGNOSIS MODE
(a) Start up diagnosis mode.
HINT:
Follow the method below.
(1) Insert the ignition key into the ignition key cylinder.
(2) Remove the ignition key from the ignition key cylin-
der.
(3) Insert the key into the ignition switch.
(4) Turn the ignition switch ON once within 5 sec.
(5) Repeat turning the ignition switch OFF " ON 9
times within 30 sec.
(6) Enter the diagnosis mode, and make sure that the
buzzer sounds.
(b) Finishing the Diagnosis Mode.
During the Diagnosis mode, turn the ignition switch OFF
" ON to go back to the normal mode.
At this time make sure that the buzzer sounds.
Page 320 of 1897

I20456
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or
rolling code.
0.13 sec.
0.5 sec.
0.13 sec. 0.25 sec. 0.5 sec.
0.5 sec. 0.5 sec.
OFF ON
OFF ON
OFF ON
OFF ON
While receiving
I06938
Dry cell battery (1.5 V x 2)
Push BE-92
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
1696 Author: Date:
2001 AVALON (RM808U)
(c) Diagnosis Mode Check.
HINT:
Check how the buzzer sounds when pressing each transmitter
switch.
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or rolling code.
HINT:
If (4) is detected in the Diagnosis Check, conduct the recogni-
tion code registration.
(5) No response from the buzzer.
HINT:
Conduct the following checks.
Check the wireless door lock transmitter.
Check the wireless door lock receiver.
2. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control receiver and transmitter re-
placementº.
(a) Using a screwdriver, remove the cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (-) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, face the key plate of
the transmitter to the vehicle, and check the transmitter
operation when pressing transmission switch on the side
of the transmitter body.
Standard:
Remote control of vehicle door lock can be operated.
LED lights up more than once.
HINT:
The minimum operation distance differs according to op-
erator, the way of holding, and location.
As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
Page 321 of 1897

I06939
(-) terminal
I02935(+) terminal
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-93
1697 Author: Date:
2001 AVALON (RM808U)
(e) Install the battery (lithium battery).
3. CHECK BATTERY CAPACITY
HINT:
Make sure to use the TOYOTA electrical tester.
With the battery unloaded, judge can not be made wheth-
er the battery is available or not on the test.
When the transmitter is faulty, the energy amount left in
the battery might not be checked correctly.
On the lithium battery used for the transmitter, the voltage
more than 2.5 V with the battery unloaded is shown on the
tester until the energy is completely consumed.
Accordingly when inspecting the energy amount left in the
battery, it is necessary to measure the voltage when the
battery is loaded. (1.2 kW).
(a) Remove the cover using a (-) driver.
(b) Remove the battery (lithium battery) from the transmitter.
(c) Connect the lead to the (-) terminal of the transmitter and
install the battery.
(d) Connect the (+) tester to the (+) battery (lithium battery),
and (-) tester to the lead respectively.
(e) Press one of the transmitting switches on the transmitter
for approx. 1 second.
(f) Press the transmitting switch on the transmitter again to
check the voltage.
Standard: 2.1 V or more