Page 330 of 1897
BE-100
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
1704 Author: Date:
2001 AVALON (RM808U)
MPX body performs operates LOCK-UNLOCK operation 5 times at a 1 sec.
interval to inform the operator that prohibition mode has been selected.
Press again either of switches on the transmitter.
MPX body ECU automatically performs LOCK-UNLOCK operation once or
twice at a 1 sec. interval to inform the operator that it has received the signal
from the transmitter.
LOCK-UNLOCK occurs once
LOCK-UNLOCK occurs twice Registration of recognition code is completed
Registration of recognition code has not been completed.
Recognition code received first time and second time did not match.
Proceed to continue registration
If even one of the following conditions is satisfied, registration of recognition
codes in completed.
40 secs. elapses since the MPX body ECU response.
The driver's door is closed.
The key plate is inserted in the ignition key cylinder.
4 types recognition codes are registration at one time.
Registration of recognition codes (add mode or rewrite mode) is completed.
Within
3 secs. Within
40 secs.
ON
LOCK
Approx.
1 sec.Approx.
1 sec.
When prohibition
mode is selected.
Press the lock and unlock switches on the transmitter simultaneously within 1.5 sec.
If they are not performed, the mode returns to the normal mode, then start with
ºStart registration of recognition codeº.
Proceed to finish registration
Within 40 secs.
Within 3 secs.
Page 334 of 1897
BO0Y7-03
H00792Protective Tape
BO-44
- BODYBODY OUTSIDE MOULDING
1829 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. HEAT MOULDING
Using a heat light, heat the moulding to 40 - 60 °C (104 - 140
°F).
NOTICE:
Do not heat moulding excessively.
2. REMOVE OUTSIDE MOULDING
(a) Tie both piano wire ends to wooden blocks or similar ob-
jects.
(b) Cut the adhesive tape by pulling the piano wire as shown.
NOTICE:
If reusing the moulding, take care not to damage the
moulding.
Do not damage the body.
(c) Remove the moulding.
Page 341 of 1897
H12124
2 Clips
H12161
Claw
Claw
H121623 Clips
H08965
H10479
Protective
Tape
- BODYBACK WINDOW GLASS
BO-71
1856 Author: Date:
2001 AVALON (RM808U)
(b) Remove the package tray trim as shown in the illustration.
5. REMOVE UPPER BLACK SILENCER
6. w/ Rear personal light:
REMOVE REAR PERSONAL LIGHT
(a) Using a screwdriver, remove the rear personal light, then
disconnect the connector.
HINT:
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
side.
7. REMOVE ROOF HEADLINING
Disengage the 3 clips and remove the rear side of roof headlin-
ing.
8. DISCONNECT DEFOGGER WIRE CONNECTOR
9. REMOVE BACK WINDOW MOULDING
(a) Using a knife, cut off the moulding as shown.
NOTICE:
Do not damage the body with the knife.
(b) Remove the remaining moulding.
10. REMOVE BACK WINDOW GLASS
(a) Insert a piano wire between body and glass and let it pass
through.
(b) Tie both wire ends to wooden blocks or similar objects.
HINT:
Apply protective tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating the glass, take care not to damage the
paint and exterior.
Page 346 of 1897
BO2OQ-01
N01363
SST
N01364
BO2556
BO-14
- BODYFRONT DOOR
1799 Author: Date:
2001 AVALON (RM808U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Using SST, loosen the body side hinge bolts to adjust.
SST 09812-00010
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
HINT:
Substitute the bolt with washer for the centering bolt.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Loosen the striker mounting screws.
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
(c) Using a plastic hammer, tap the striker to adjust it.
Page 347 of 1897
BO2OO-01
H12112
Rear Lower FrameDoor Lock Striker23 (230, 17)
Front Door Weatherstrip
Door Glass Run
Outside Rear View
Mirror
Door Glass
Lower Frame
Bracket Garnish
7.8 (80, 69 in.´lbf)25 (260, 19)
5.4 (55, 48 in.´lbf)
Outside Handle
Key Cylinder
5.4 (55, 48 in.´lbf)
Door
Hinge
7.8 (80, 69 in.´lbf)
Door Check
25 (260, 19)
Door Speaker BoardFront Lower
Frame
25 (260, 19)
Door Hinge
Front Door Outside Lower Moulding
Door Lock Protector
Service Hole Cover
5.4 (55, 48 in.´lbf)
Precoated part
Door LockInside Handle
4.9 (50, 43 in.´lbf)
Inside Handle
Bezel
Cover
Door TrimUpper Armrest
Base Panel
Power Window Switch
Front Door Armrest
Courtesy Light
Front Door
Belt Moulding Front Door
Inner Weatherstrip
x10
5.4 (55, 48 in.´lbf)
Window Regulator
Guide Assembly
5.4 (55, 48 in.´lbf)
x8
x4
Window Regulator Motor
No. 2 Service Hole Cover
Front Door Trim Pocket : Specified torqueN´m (kgf´cm, ft´lbf)
BO-8
- BODYFRONT DOOR
1793 Author: Date:
2001 AVALON (RM808U)
FRONT DOOR
COMPONENTS
Page 352 of 1897
H12110
- BODYFRONT DOOR
BO-13
1798 Author: Date:
2001 AVALON (RM808U)
19. REMOVE DOOR LOCK
(a) Disconnect the 2 control links from the outside handle and
door lock cylinder.
(b) Disconnect the connector.
(c) Remove the 3 torx screws, bolt and door lock.
Torque:
Bolt: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
Screw: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
HINT:
Remove the door lock through the service hole.
HINT:
At the time of reassembly, please refer to the following item.
Apply adhesive to 3 screws.
Part No. 08833-00070, THREE BOND 1324 or equiva-
lent
(d) Remove the 2 screws and door lock protector from the
door lock.
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the sliding and rotating parts of the door
lock.
20. REMOVE OUTSIDE HANDLE
(a) Remove the 2 bolts and outside handle with key cylinder.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Remove the bolt and key cylinder from the outside han-
dle.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
Page 357 of 1897
BO2QA-01
- BODYFRONT SEAT (Manual Adjuster Type)
BO-1 15
1900 Author: Date:
2001 AVALON (RM808U)
INSPECTION
INSPECT RECLINING LOCK POSITION AND SLIDING LOCK POSITION SLIPPING OFF
(a) When reclining the seat, inspect that the outer and inner recliners are released at the same time.
HINT:
When the reclining lock position slips off, disassemble the seat to adjust the position.
(b) When sliding the seat, inspect that the outer and inner tracks are locked at the same time.
HINT:
When sliding lock positions slip off, loosen the bolts to adjust the position.
Page 358 of 1897
BO2QC-01
BO-1 18
- BODYFRONT SEAT (Manual Adjuster Type)
1903 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
INSTALL FRONT SEAT
(a) Slide the front seat to the frontmost position.
NOTICE:
Make sure that the seat adjuster locks.
(b) Without holding the seat track handle, mount the seat to the vehicle.
HINT:
If holding the seat track handle, the adjusted frontmost positions will slip off.
(c) Connect the airbag connector.
(d) Tighten the bolts on the rear side temporarily, tighten them completely starting from the bolt on the inner
side.
Torque: 37 N´m (375 kgf´cm, 27 ft´lbf)
(e) Slide the seat to the rearmost position to install the bolts on the front side.
Torque: 37 N´m (375 kgf´cm, 27 ft´lbf)
