Page 312 of 1897
BE-8
- BODY ELECTRICALTROUBLESHOOTING
1612 Author: Date:
2001 AVALON (RM808U)
POWER MIRROR CONTROL SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
ELECTRO CHROMIC MIRROR SYSTEM
SymptomSuspect AreaSee page
Electro Chromic Inner Mirror does not operate.
1. ECU-IG Fuse
2. Elector Chromic Inner Mirror
3. Wire Harness
BE-120
SEAT HEATER SYSTEM:
SymptomSuspect AreaSee page
Seat heaters do not operate.
(Driver's and Passenger's)1. SEAT HEATER Fuse
2. Ignition Main Relay
3. Wire Harness-
BE-122
-
Driver's seat heater does not operate.
1. Seat Heater Switch (Driver's)
2. Seat Heater
3. Wire HarnessBE-122
BE-122
-
Passenger's seat heater does not operate.
1. Seat Heater Switch (Passenger's)
2. Seat Heater
3. Wire HarnessBE-122
BE-122
-
Seat Heater temperature is too hot.1. Seat HeaterBE-122
GARAGE DOOR OPENER SYSTEM
SymptomSuspect AreaSee page
The equipment of which code has been registered does not oper-
ate.1. Garage Door Opener
2. Wire Harness
3. *BE-170
LED does not light up. (Even though either switch is pressed.)1. Garage Door Opener
2. Wire HarnessBE-170
LED does not light up. (Only one switch is pressed.)1. Garage Door OpenerBE-170
* As the GARAGE DOOR OPENER on the vehicle side seems to be normal, check the OPENER on the
equipment side, of which code has been registered.
Page 313 of 1897
BE0I1-04
I12796
Left TurnRight Turn
54
1 2 3
15 166
7 8
9 10
11 17
14 13 12
I12792
BE1843
3
2
1
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
BE-29
1633 Author: Date:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT TURN SIGNAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Left turn1 - 2Continuity
Neutral-No continuity
Right turn2 - 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HAZARD WARNING SWITCH CONTINUITY
ConditionTester connectionSpecified condition
OFF5 - 7Continuity
ON5 - 6,
1 - 2 - 3 - 4Continuity
Illumination circuit8 - 9Continuity
If continuity is not as specified, replace the switch.
3. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (-) lead to terminal 3.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, check that the bulbs flash.
HINT:
The turn signal lights should flash 60 or 120 times per min-
ute.
If one of the front or rear turn signal lights has an open cir-
cuit, the number of flashers will be more than 140 per min-
ute.
If operation is not as specified, replace the flasher.
Page 314 of 1897
BE0I0-04
I12526
Turn Signal Light
Combination Switch
Turn Signal Switch
Turn Signal Light
Hazard Warning Switch
Flasher Relay
Engine Room Junction Block
HAZ Fuse
Driver Side Junction Block
TURN Fuse
BE-28
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
1632 Author: Date:
2001 AVALON (RM808U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION
Page 320 of 1897
I20456
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or
rolling code.
0.13 sec.
0.5 sec.
0.13 sec. 0.25 sec. 0.5 sec.
0.5 sec. 0.5 sec.
OFF ON
OFF ON
OFF ON
OFF ON
While receiving
I06938
Dry cell battery (1.5 V x 2)
Push BE-92
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
1696 Author: Date:
2001 AVALON (RM808U)
(c) Diagnosis Mode Check.
HINT:
Check how the buzzer sounds when pressing each transmitter
switch.
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or rolling code.
HINT:
If (4) is detected in the Diagnosis Check, conduct the recogni-
tion code registration.
(5) No response from the buzzer.
HINT:
Conduct the following checks.
Check the wireless door lock transmitter.
Check the wireless door lock receiver.
2. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control receiver and transmitter re-
placementº.
(a) Using a screwdriver, remove the cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (-) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, face the key plate of
the transmitter to the vehicle, and check the transmitter
operation when pressing transmission switch on the side
of the transmitter body.
Standard:
Remote control of vehicle door lock can be operated.
LED lights up more than once.
HINT:
The minimum operation distance differs according to op-
erator, the way of holding, and location.
As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
Page 332 of 1897
BO0Y8-03
H12138
Adhesive Tape
Adhesive TapeAdhesive Tape
Adhesive Tape
- BODYBODY OUTSIDE MOULDING
BO-45
1830 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
1. CLEAN BODY MOUNTING SURFACE
(a) Using a heat light, heat the body mounting surface to 40
- 60 °C (104 - 140 °F).
NOTICE:
Do not heat the body excessively.
(b) Remove the adhesive tape from the body.
(c) Wipe off stains with cleaner.
2. CLEAN MOULDING
If reusing moulding:
(a) Using a heat light, heat the moulding to 20 - 30 °C (68 -
86 °F).
NOTICE:
Do not heat the moulding excessively.
(b) Remove the adhesive tape from the moulding.
(c) Wipe off stains with cleaner.
(d) Apply a new adhesive tape to the moulding as shown in
the illustration.
3. INSTALL MOULDING
(a) Using a heat light, heat the body and moulding.
Body: 40 - 60 °C (104 - 140 °F)
Moulding: 20 - 30 °C (68 - 86 °F)
NOTICE:
Do not heat the moulding excessively.
(b) Lift the moulding release sheet from the face of moulding.
NOTICE:
When the moulding release sheet is removed, make sure
that no dirt or dust can get onto the coated area.
Page 334 of 1897
BO0Y7-03
H00792Protective Tape
BO-44
- BODYBODY OUTSIDE MOULDING
1829 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. HEAT MOULDING
Using a heat light, heat the moulding to 40 - 60 °C (104 - 140
°F).
NOTICE:
Do not heat moulding excessively.
2. REMOVE OUTSIDE MOULDING
(a) Tie both piano wire ends to wooden blocks or similar ob-
jects.
(b) Cut the adhesive tape by pulling the piano wire as shown.
NOTICE:
If reusing the moulding, take care not to damage the
moulding.
Do not damage the body.
(c) Remove the moulding.
Page 335 of 1897
BO2PK-01
H12166
w/ Rear personal light:
Rear Personal Light
RH Roof Side
Inner Garnish
Back Window
Moulding
Back Window Glass
w/ Speaker:
High-mounted
Stop Light
LH Roof Side Inner Garnish
Package Tray Trim
Upper Back Silencer
Rear Seatback
Rear Seat
Outer Belt RH
Rear Seat Inner
with Center Belt Rear Seat Cushion Roof Headlining
Rear Door
Opening Trim No. 1 Stopper
No. 2 Stopper
No. 1 Stopper
No. 2 Stopper
: Specified torque
N´m (kgf´cm, ft´lbf)
Non-reusable partw/o Speaker:
High-mounted Stop Light
Rear Seat Inner Belt
41 (420, 30)
41 (420, 30)41 (420, 30)
18 (185, 13)
18 (185, 13)
Rear Seat Outer Belt LH
- BODYBACK WINDOW GLASS
BO-69
1854 Author: Date:
2001 AVALON (RM808U)
BACK WINDOW GLASS
COMPONENTS
Page 339 of 1897
H08966
BO-76
- BODYBACK WINDOW GLASS
1861 Author: Date:
2001 AVALON (RM808U)
HINT:
Confirm that the moulding is attached to the body panel as
shown in the illustration.
(b) Hold the back window glass in place securely with a pro-
tective tape or equivalent until the adhesive hardens.
NOTICE:
Take care not to drive the vehicle during the time described
in the table below.
TemperatureMinimum time prior to driving the vehicle
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5 °C (41 °F)24 hours
12. INSPECT FOR LEAK AND REPAIR
NOTICE:
Conduct a leak test after hardening time has elapsed.
13. CONNECT DEFOGGER WIRE CONNECTOR
14. INSTALL ROOF HEADLINING
15. w/ Rear personal light:
INSTALL REAR PERSONAL LIGHT
16. INSTALL UPPER BACK SILENCER
17. INSTALL PACKAGE TRAY TRIM
18. INSTALL HIGH-MOUNTED STOP LIGHT
19. INSTALL ROOF SIDE INNER GARNISH
20. INSTALL REAR SEAT (See page BO-123)
