2001 TOYOTA AVALON light

BE216-01
I21290
Calendar
LIGHT Button
MODE Button RESET/ADJ Button
I21291
I21283
I21284
BE-64
- BODY ELECTRICALCOMPASS
1668 Author
: Date
:
2001 AVALON (RM808U)
COMPASS
ADJUSTMENT
1. MULTI INFORMATION DISPLAY ILLUMINATION
Turn the ignition switch to the ON position and illuminate the all
parts of the display by pushing the ºLIGHTº button.
2. PERFORM CIRCLING CALIBRATION
(a) Push the ºMODEº button several times until ºCOM-
PASSºappears and blinks on the calendar display.
(b) Then push the ºRESET/ADJº button. ºCALIBRATEº ap-
pears and blinks together with the compass display.
(c) Drive the vehicle in a circle until the blinking stops.
(d) If there is not enough space to drive in a circle, drive
around the block until the blinking stops.
(e) When the compass and the calendar display return to
normal mode, calibration is complete

I12825
34 4017 18
BE0IG-03
I12826
34
17 18
40
ON
ON
W/ Mirror Heater:
W/O Mirror Heater:
I057411
2 34
4 321
I13308
3
6
I13307
5
10
- BODY ELECTRICALDEFOGGER SYSTEM
BE-67
1671 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
1. A/C control panel assembly:
INSPECT DEFOGGER SWITCH OPERATION
(a) Connect the positive (+) lead from the battery to terminal
17, 18 and negative (-) lead to terminal 40.
(b) Connect the positive (+) lead from the battery to terminal
24 through a 1.4 W test bulb.
(c) Turn the defogger switch ON and check that the test bulb
and indicator light turn ON, then turn OFF after about 15
minutes.
If operation is not as specified, proceed to the next inspection.
2. INSPECT DEFOGGER RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant3 - 4Continuity
Apply B+ between
terminals 3 and 4.1 - 2Continuity
If continuity is not as specified, replace the relay.
3. W/ Mirror defogger:
INSPECT MIRROR DEFOGGER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative (-) lead to terminal 6.
(b) Check that the mirror becomes warm.
HINT:
It will take a short time for the mirror to become warm.
If the mirror does not become warm, replace the mirror assem-
bly.
4. W/ Mirror defogger and driving position memory:
INSPECT MIRROR DEFOGGER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
5 and the negative (-) lead to terminal 10.
(b) Check that the mirror becomes warm.
HINT:
It will take a short time for the mirror to become warm.
If the mirror does not become warm, replace the mirror assem-
bly.

I12835
21
BE1ED-01
BE-120
- BODY ELECTRICALELECTRO CHROMIC MIRROR SYSTEM
1724 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
INSPECT ELECTRO CHROMIC INNER MIRROR OPERA-
TION
(a) Connect the positive (+) lead the battery to terminal 1 and
the negative (-) lead to terminal2.
(b) Shine an electric light on the mirror, and check that there
is battery positive voltage and mirror surface becomes
ºbrightº to ºdarkº.
If operation is not as specified, replace the inner mirror.

BE0B2-14
START
Insert the key in the key cylinder.
Under registration
Registration completion
Remove the key.
Will you register the
next key?
NoSecurity indicator blinks until the first
key is inserted. The indicator lights up
after the key registration.
Security Indicator ON
Security Indicator
OFF
END Ye s
Security Indicator ON
(After the last key (sub-key)
has been registered, the indi-
cator goes off.)
BE-172
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
1776 Author
: Date
:
2001 AVALON (RM808U)
ENGINE IMMOBILISER SYSTEM
REGISTRATION PROCEDURE
1. KEY REGISTRATION IN AUTOMATIC REGISTRATION MODE
(a) Registration of a new transponder key.
HINT:

This must be done when you have installed a new ECM.

The new ECM is in the automatic key code registration mode. The already fixed number of key codes
for this ECM can be registered.
On this type of vehicle, up to 4 key codes can be registered.

In the automatic registration mode, the last key registered becomes sub-key.

1.8 Sec.
0.2 Sec.
0.25 Sec. 0.5 Sec.0.25 Sec.
1 Sec. Blinks Code 2-1 Code2-2
0.25 Sec.
0.25 Sec.0.5 Sec. 1 Sec.
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE-173
1777 Author
: Date
:
2001 AVALON (RM808U)
HINT:

When a key is not inserted in the key cylinder in the automatic registration mode, the security indicator
always lights on.

When the immobiliser system operations normally and the key is pull out, the security indicator blinks.

When key code registration could not be performed in the automatic registration mode, code 2-1 is
output from the security indicator and when inserting the already registered key, code 2-2 is output.
(b) Automatic registration mode completion
If completing the mode forcibly when more than 1 key code have been registered in the automatic reg-
istration mode, perform the following procedures.
After 1 more key code have been registered with master key, perform step (1) or (2) without pulling
the key out or inserting the already registered key.
(1) Depress and release brake pedal 5 times or more within 15 secs.
(2) With the hand-held tester, require automatic registration mode completion.

BE052-07
I12791
A
- BODY ELECTRICALFOG LIGHT SYSTEM
BE-27
1631 Author
: Date
:
2001 AVALON (RM808U)
ADJUSTMENT
ADJUST FOG LIGHT AIM
A-bolt: Vertical Direction

BE0HZ-04
I12795
OFFON
54
1 2 3
15 166
7 8
9 10
11 17
14 13 12
I05027
1 2
3 55
2 13
BE-26
- BODY ELECTRICALFOG LIGHT SYSTEM
1630 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT FOG LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF-No continuity
ON10 - 11Continuity
If continuity is not as specified, replace the switch.
2. INSPECT FOG LIGHT RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 - 2Continuity
Apply B+ between
terminals 1 and 2.3 - 5No continuity
If continuity is not as specified, replace the relay.

BE050-07
I12525
Fog Light
Combination Switch

Fog Light Switch
Driver Side Junction Block

Fog Light Relay

FOG Fuse
- BODY ELECTRICALFOG LIGHT SYSTEM
BE-25
1629 Author
: Date
:
2001 AVALON (RM808U)
FOG LIGHT SYSTEM
LOCATION